Mitsubishi Electronics LVP-X120A user manual Picture adjustment, Adjustment from personal computer

Page 20
Picture adjustment

Picture adjustment

Adjustment from personal computer

Although this projector sets proper signal settings set automatically for the image signal from personal computers. But at times, there can be some diferences in timings. In this case, press AUTO POSITION button. If the images are still not pro- jected correctly, use MENU display to adjust the projected images from personal computers. Afteradjustments are made, the new settings can be saved in user function.

Adjusting the images from personal computers in MENU display

Adjust as below for the following symptoms.

Image moves to right or left :

Adjust HORIZ. POSITION in SIGNAL menu. Press the % button to move the image to left. Press the $ button to move the image to right.

Image moves to up or down :

Adjust VERT. POSITION in SIGNAL menu. Press the % button to move the image to upward. Press the $ button to move the image to down.

Image flickers / Image is out of focus : Adjust FINE SYNC. in SIGNAL menu.

Wide stripes appear :

Adjust CLAMP POSITION or CLAMP WIDTH of each menu in SIGNAL - USER menu.

Noise etc. appears on right or left side of image: Adjust HORIZ. PIXELS of the menu in SIGNAL - USER menu.

Noise etc. appears on top or bottom part of image : Adjust VERT. LINES of the menu in SIGNAL - USER menu.

Top part of image curves :

Change the setting of HOLD in SIGNAL menu or

PLL in SIGNAL - USER menu.

HOLD ... Select ON, and adjust BEGIN or END for image which top part is the least curved.

PLL ....... Select FAST, NORMAL, or SLOW for

image which top part is the least curved. Select AUTO for normal setting.

Image does not move naturally :

Adjust VERT. SYNC. of the menu in SIGNAL - USER menu. Select AUTO for normal setting.

Do not change each menu setting in SIGNAL - USER menu for normal setting.

Memorizing the setting

1.Select MEMORIZE in SIGNAL menu, and press the ENTER button.

2.Press the $ or % button to select the memory which you wish to record (USER 1 or USER 2).

3.Press ENTER button.

Initializing the setting which has been changed Select RESET in SIGNAL menu, and press ENTER button.

When initializing, selection buttons will not work for about 2 - 18 seconds.

Seeing images in recorded setting.

Select AUTO in SIGNAL menu, and press the$ or

%button to select the memory (USER1 or USER2).

Resetting the recorded setting

1.Select DELETE in SIGNAL menu, and press ENTER button.

2.Press the$ or % button to select the memory which you wish to reset (USER 1 or USER 2).

3.Press ENTER button

The recorded setting will be reset.

The simple way of adjustment

1.Select HORIZ. POSITION in SIGNAL menu.

2.Press the$ or % button to adjust the horizontal start position (the left end).

3.Select TRACKING in SIGNAL menu.

4.Press the$ or % button to adjust the horizontal end position (the right end).

5.Repeat steps 1 to 4 for fine adjustment.

6.Select VERT. POSITION in SIGNAL menu.

7.Press the$ or % button to adjust the vertical start position (the top end).

20

Image 20
Contents X120 LCD Projector User ManualMODEL LVP-X120A ENGLISH FRANÇAIS ESPAÑOL APPENDIXDO NOT REMOVE COVER OR BACK NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNELRISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCKContents Trademark, Registered trademarkImportant safeguards Unplug immediately if there is something wrong with your projector Never remove the cabinetDo not modify this equipment If you break or drop the cabinetremote control sensor Front / Rear powerindicators Overview of the projectoradjustment foot up and down filter cover adjustment foot right and leftFront lamp lid MAIN powerOverview of the remote control About laser beampower input source auto position +, - volumeBattery installation Operation areaPreparing the projector for operation screenOrientation of the projector Front projectionAdjusting the angle of projection Getting ready for projectionground terminalBasic connections Projector + AV equipmentCables and adapters Projector + DVD playerProjector + IBM PC or IBM PC compatibles When outputting to both a PC monitor and the projectordesktop computer notebook computerBasic connections continue Projector + MacintoshPower Book desktopTo operate projector power ON LAMPTEMP CARDTo operate projector power ON continue Turning off the projectorThe volume from the speaker AUTO POSITION buttonMenu operation Basic operationSetting range is different according to the type of the signalMenu setting continue 3 INSTALLATION1 PICTURE 2 PRESENTATION5 SIGNAL Picture adjustment Adjustment from personal computerAdjusting the images from personal computers in MENU display Memorizing the settingSpecification of RGB signals in each computer mode of the projector Advanced feature for presentation ExpandStill Setting the Expand modePC-CARD Using the PC-CARDSetting up the PC-CARD During PC-CARD playback, the sound is switched offPC-CARD Continue Advanced feature with PC Installation of softwarePCV PC Card Viewer EnvironmentCommand reference For Windows Advanced feature with PC ContinueStarting up PCV For Windows Recording the image For Windows Editing the presentation For Windows Delete the imageSequencing A. Exchange images Preview an imageCommand reference Starting up PCV For MacintoshRecording the image For Macintosh Editing the presentation For Macintosh Mouse remote control ConnectionOperation Projector + IBM PC or IBM PC compatiblesReplacement of a light source lamp The life of the lamp How to reset the operation time meterMaintenance Cleaning the air-filterCleaning the projector and the ventilation slots Cleaning the lensTroubleshooting PROBLEMSPOSSIBLE SOLUTIONS CAUSEENTER IndicatorsSOURCE MENU Accessories SpecificationsReplacement parts list APPENDIX Control this projector by using a personal computer Connection Projector + IBM PC or IBM PC compatibles3 Control sequence 2 Control command diagram1 Interface 5 Remote commands Control this projector by using a personal computer Continue4 Operation commands 6 Warning commands 7 Reading command diagram8 Picture adjustment commands MITSUBISHI ELECTRONICS AMERICA, INC 5665 Plaza Drive Cypress, CA871D269B1 Printed in Japan