Mitsubishi Electronics HD4000 Setting up your projector, Setting up the screen, Basic setup

Page 10

Setting up your projector

Setting up the screen

Install the screen perpendicularly to the projector. If the screen can not be installed in such a way, adjust the projection angle of the projector. (See below.)

•Install the screen and projector so that the projector’s lens is placed at the same height and horizontal position of the screen center.

•Do not install the screen where it is exposed to direct sunlight or lighting. Light directly reflecting on the screen makes the projected images washed-out and hard to view.

SCREEN SIZE

You can keep the image display area within the screen by setting SCREEN SIZE in the INSTALLATION menu according to the size of the actual screen.

When setting SCREEN SIZE to CINEMA SCOPE(2.35:1):

•CinemaScope size movies are projected in the full screen.

•Set ASPECT in the FEATURE menu to 16:9 when displaying Vista-size images. In this case, they are squeezed horizontally.

•When ASPECT in the FEATURE menu is set to AUTO and 480p, 720p, or 1080i signal is input, the part for displaying subtitles is not projected.

Basic setup

Determine the distance from the screen to the projector according to the size of the images to be projected. (See page 12.)

W

AB

A=B

VERTICAL LOCATION

You can adjust the vertical position of the displayed image using VERTICAL LOCATION in the INSTALLATION menu.

(Example) To move the displayed image up:

Maximum panel size (WXGA 15:9)

Empty area

Empty area

Set SCREEN SIZE in the

Set VERTICAL LOCATION in the

INSTALLATION menu to 720p(16:9)

INSTALLATION menu to +6.

•When you increase the value of VERTICAL LOCATION too much, the displayed image may be out of the screen partially.

•Do not place this projector on a carpet or blanket because the exhaust vent and the intake vent on the bottom surface are blocked and the projector would heat, causing a breakdown or fire.

•Depending on the installation conditions, warm air that is emitted from the exhaust vents may flow into the intake vent, causing the projector to display “TEMPERATURE!!” and then stop projecting images.

Adjusting the projection angle

This projector is provided with three feet for adjusting the projection angle on the bottom surface. Adjust the projection angle depending on the position of the projector.

Adjustment of the projection angle

For the best projection, project images on a flat screen installed at 90 degrees to the floor. If necessary, tilt the projector using the two adjustment feet on the bottom of the projector.

1.Tilt up the projector to the appropriate angle.

2.Press the foot adjustment buttons next to the

Screen

Adjustment feet (rear)

adjustment feet (rear), and the adjustment feet will come out.

3.Release the buttons to lock the adjustment feet (rear) to that position.

4.Rotate the adjustment feet (rear) for fine adjustment.

After using the projector:

5.Put the adjustment feet (rear) back into the projector by pressing the foot adjustment

buttons.

•If necessary, rotate the adjustment feet (front) for fine adjustment.

When projected images are distorted to a trapezoid:

When the screen and the projector are not placed perpendicularly to each other, projected images become trapezoidal. If you cannot make the projector and the screen perpendicular to each other by mechanical adjustments, adjust keystone. (See page 18.)

•When the keystone adjustment is applied, the correct aspect ratio may not be obtained.

•When the keystone adjustment is applied, the resolution lowers. In addition, vertical stripes ap- pear and straight lines bend in images with com- plicated patterns. To prevent such symptoms, keep the screen and the projector perpendicular to each other as much as possible.

•Though the projected image may be distorted momentarily when you change the setting value of the keystone adjustment, such symptom is not a malfunction.

•Though the projected image may be distorted depending on the setting value of the keystone adjustment and the type of the input signal, such symptom is not a malfunction. In such a case, adjust the setting value within the range where the projected image is not distorted.

•The setting value displayed at the time of the keystone adjustment may vary depending on the type of the input signal.

•The keystone mode does not function when the REAL mode is applied.

•Displayed image may be distorted during key- stone adjustment.

EN-10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents HD4000 EN-2 When using the projector in EuropeRisk of Electric Shock Do not Open Contents Important safeguards EN-4EN-5 Preparing your projector Checking accessoriesInserting the batteries into the remote control CablesControl area Terminal panel OverviewEN-7 Preparing your projector Remote controlUsing the picture quality adjusting buttons Bottom sideReception angle Using the remote controlOperational range of the remote control EN-9Basic setup Setting up your projectorSetting up the screen Adjusting the projection angleTrigger terminal With the Installation menu See page 24 for menu settingTo cancel the menu EN-11Screen size and projection distance Setting up your projectorWhen the aspect ratio of the screen is EN-12Basic home theater system connection Connecting the projector to video equipmentViewing video images EN-13When a TV tuner or VCR is connected Connecting to a video player, etcConnecting to a DVD player or Hdtv decoder Viewing video imagesConnection for video equipment having a Hdmi terminal EN-15Connection for video equipment having a DVI-D terminal Plugging in the power cord EN-16Projecting images EN-17EN-18 When projected images are distorted to a trapezoidTo stop projecting Following casesWith the remote control Setting the aspect ratioHow to change the settings With the Feature menuViewing computer images Connecting the projector to a computerPlugging the power cord EN-20Projecting images EN-21Viewing computer images When connecting to a notebook computerExample of the setting procedure for external output Auto Position buttonMenu operation EN-23Menu operation How to set the menusAvailable settings in the menus EN-24Feature menu Installation menuEN-25 AV memory EN-26To adjust the color Color and Tint Adjusting projected imagesTo adjust the brightness Contrast and Brightness To sharpen or soften the projected image SharpnessAbout color temperature Adjusting projected imagesTo adjust the tone of white Color Temp To adjust the ratio of change in brightness Gamma ModeTo adjust the vertical position EN-29To enable the password function Advanced featuresPassword function To cancel the password functionCleaning Using filterInstallation Cleaning the filterReplacing the lamp Interval of lamp replacementEN-32 Reset of the lamp operation time Cleaning of the projector and the ventilation slotsCleaning of the lens To replace the lampSolution TroubleshootingNo image appears on the screen Problem EN-34EN-35 No image appears on the screen Problem SolutionProblem Solution Images are not displayed correctlyOthers Problem Solution TroubleshootingImages are not displayed correctly Problem Solution EN-36Abnormal condition IndicatorsNormal condition EN-37Specifications Dimension Drawings unit mmEN-38 EN-39 ConnectorsReplacement part Option / Not included in the box VLT-HC900LPMitsubishi Projector Contact Information

HD4000 specifications

Mitsubishi Electronics has long been a pioneer in the field of electronics, and their HD4000 model stands as a testament to their commitment to innovation and quality. Designed for both commercial and residential applications, the HD4000 integrates advanced technologies to deliver exceptional performance and versatility.

One of the standout features of the Mitsubishi HD4000 is its high-definition capabilities. With native support for 4K resolution, this model ensures crystal-clear images with stunning detail. The enhanced picture quality is complemented by advanced image processing technologies, including HDR (High Dynamic Range) support, which allows for a broader range of colors and contrasts. This results in a more lifelike viewing experience, making any visual content come alive.

In terms of connectivity, the HD4000 is equipped with multiple input options, including HDMI, USB, and VGA ports. This versatility enables seamless integration with various devices such as PCs, gaming consoles, and multimedia players. The built-in Wi-Fi capability further enhances its functionality, allowing users to stream content directly from the internet without the need for additional cables.

Mitsubishi has also prioritized energy efficiency in the HD4000. With its eco-friendly design and energy-saving features, this model not only reduces electricity consumption but also contributes to a lesser environmental impact. The automatic brightness adjustment feature is particularly noteworthy, as it optimizes the display according to ambient light conditions, ensuring optimal visibility while conserving energy.

The build quality of the HD4000 is robust, designed for longevity and reliability. The sleek design makes it suitable for various settings – from modern offices to home entertainment centers. The intuitive user interface simplifies navigation through the extensive features, making it accessible for users of all technical levels.

Additionally, the HD4000 comes equipped with advanced audio technologies that enhance the auditory experience. With integrated surround sound systems and support for various audio formats, users can expect rich and immersive sound quality that complements the stunning visuals.

Overall, the Mitsubishi Electronics HD4000 combines cutting-edge technology, energy efficiency, and superior build quality, making it an excellent choice for those seeking high-performance display solutions. Whether for professional use or home entertainment, the HD4000 promises to deliver an impressive viewing experience that meets the demands of modern users.
Top Page Image Contents