Mitsubishi Electronics HD4000 user manual Projecting images, EN-21

Page 21

C. Projecting images

Preparation:

•Remove the lens cap.

•Turn on the power of the connected computer.

FOCUS ring

ZOOM ring

POWER button

 

 

POWER STATUS

 

 

COMPUTER button

ON ( I ) button HDMI button

COMPUTER button

ENGLISH

1.Confirm the POWER indicator lights-up red.

•If the projector was turned off before the lamp had cooled down sufficiently, the fan may start rotating and the POWER button may not work after the power cord is plugged. (The STATUS indicator blinks green.) After the fan stops rotating, press the power button to turn back on the POWER indicator.

2.Press the POWER button on the projector or ON ( I ) button on the remote control.

•It may take about one minute for the lamp to light up.

•The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.

•Do not cover the lens with the lens cap while the lamp is on. Do not strip off the aluminium sheet inside the lens cap.

•After the POWER button is pressed, the image may flicker before the lamp becomes stable. This is not a prod- uct malfunction.

•LAMP MODE can't switch for 1 minute after the power ON.

•The projector starts warming up when the POWER button is pressed. During the warm-up process, images may appear dark and no commands are accepted.

•By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when the STATUS indicator blinks red. (See page 37.)

3.Select an input source.

•Press the COMPUTER button on the projector or the COMPUTER or HDMI button on the remote control that is corresponding to the terminal in use.

•The input source is switched between COMPUTER and HDMI every time you press the COMPUTER button on the projector.

•Though it may take some time before an image is displayed on the screen depending on the type of the input signal, such symptom is not a malfunction.

•Images may not be projected in the correct position, depending on the type of the input signal. In such a case, press the AUTO POSITION button. (See page 22.)

•The projector automatically selects the appropriate signal format. The selected signal format is displayed on the screen.

•The COMPUTER and HDMI buttons don't function while the menu is being displayed.

• When COMPUTER is chosen as the source, images supplied from the computer may flicker. Press the or button on the remote control to reduce flicker, if it occurs.

4.Adjust the position of the projector to keep an appropriate projection distance with which images are projected in their specified sizes.

5.Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page 10.)

• When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See page 10.)

6.Adjust the size of the projected image by turning the ZOOM ring.

7.Adjust the focus by turning the FOCUS ring.

Repeat steps 4 to 7, if necessary.

EN-21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents
HD4000 When using the projector in Europe EN-2Risk of Electric Shock Do not Open Contents EN-4 Important safeguardsEN-5 Inserting the batteries into the remote control Checking accessoriesPreparing your projector CablesOverview Control area Terminal panelEN-7 Using the picture quality adjusting buttons Remote controlPreparing your projector Bottom sideOperational range of the remote control Using the remote controlReception angle EN-9Setting up the screen Setting up your projectorBasic setup Adjusting the projection angleTo cancel the menu With the Installation menu See page 24 for menu settingTrigger terminal EN-11When the aspect ratio of the screen is Setting up your projectorScreen size and projection distance EN-12Viewing video images Connecting the projector to video equipmentBasic home theater system connection EN-13Connecting to a DVD player or Hdtv decoder Connecting to a video player, etcWhen a TV tuner or VCR is connected Viewing video imagesEN-15 Connection for video equipment having a Hdmi terminalConnection for video equipment having a DVI-D terminal EN-16 Plugging in the power cordEN-17 Projecting imagesTo stop projecting When projected images are distorted to a trapezoidEN-18 Following casesHow to change the settings Setting the aspect ratioWith the remote control With the Feature menuPlugging the power cord Connecting the projector to a computerViewing computer images EN-20EN-21 Projecting imagesExample of the setting procedure for external output When connecting to a notebook computerViewing computer images Auto Position buttonEN-23 Menu operationAvailable settings in the menus How to set the menusMenu operation EN-24Installation menu Feature menuEN-25 EN-26 AV memoryTo adjust the brightness Contrast and Brightness Adjusting projected imagesTo adjust the color Color and Tint To sharpen or soften the projected image SharpnessTo adjust the tone of white Color Temp Adjusting projected imagesAbout color temperature To adjust the ratio of change in brightness Gamma ModeEN-29 To adjust the vertical positionPassword function Advanced featuresTo enable the password function To cancel the password functionInstallation Using filterCleaning Cleaning the filterInterval of lamp replacement Replacing the lampEN-32 Cleaning of the lens Cleaning of the projector and the ventilation slotsReset of the lamp operation time To replace the lampNo image appears on the screen Problem TroubleshootingSolution EN-34Problem Solution No image appears on the screen Problem SolutionEN-35 Images are not displayed correctlyImages are not displayed correctly Problem Solution TroubleshootingOthers Problem Solution EN-36Normal condition IndicatorsAbnormal condition EN-37Dimension Drawings unit mm SpecificationsEN-38 Replacement part Option / Not included in the box ConnectorsEN-39 VLT-HC900LPMitsubishi Projector Contact Information