Mitsubishi Electronics HC3100 Adjusting projected images, EN-30, To adjust the vertical position

Page 30

Adjusting projected images (continued)

This projector automatically and properly projects video signals supplied from the computer. However, some video signals may not be projected, depending on the type of the computer. In such a case, press the AUTO POSITION button. (See page 22.) When the signal is still not projected properly, adjust the projected image using the SIGNAL menu.

How to adjust the image supplied from the computer using the menu:

Carry out the following procedures according to the symptoms.

Wide strips appear. ……………………………………… Adjust TRACKING in the SIGNAL menu.

The projected image flickers.

The projected image is blurred. ………………………… Adjust FINE SYNC. in the SIGNAL menu.

The projected image is displaced horizontally. ……… Adjust HORIZ.POSITION in the SIGNAL menu. Every time the

button is pressed, the image moves to the right. Every time the button is pressed, the image moves to the left.

The projected image is displaced vertically. ………… Adjust VERT.POSITION in the SIGNAL menu. Every time the

 

 

button is pressed, the image moves down. Every time the

 

 

button is pressed, the image moves up.

The top part of the image flags. ………………………

Change the setting of HOLD in the SIGNAL menu. Select ON ,

 

 

press the ENTER button, and adjust BEGIN or END to minimize

 

 

the flagging.

A solid black or solid white appears in the image.

Adjust CLAMP POSITION or CLAMP WIDTH in the SIGNAL -

 

 

USER menu.

The motion doesn’t run smoothly.………………………

Adjust VERT. SYNC. in the SIGNAL - USER menu. Select

 

 

AUTO for normal use.

Noise appears on the right or left half of the image.

… Adjust SHUTTER (LS) or SHUTTER (RS) in the SIGNAL - USER menu.

Noise appears on the top or bottom part of the image. Adjust SHUTTER (U) or SHUTTER (L) in the SIGNAL - USER menu.

1.Display the SIGNALmenu.

2.Press the or button to select an item to adjust.

3.Adjust the selected item by pressing the or button.

To cancel the menu:

4. Press the MENU button.

Do not change the settings of the SIGNAL menu in normal use.

Simple method to adjust the image position

To adjust the horizontal position:

1.Align the left edge of the image with the left side of the screen by adjusting HORIZ.POSITION. Then, align the right edge of the image with the right side of the screen by adjusting TRACKING.

2.Repeat step 1 above to complete the adjustment of the horizontal position.

To adjust the vertical position:

3. Align the upper edge of the image with the upper side of the screen by adjusting VERT.POSITION.

LPF

You can select whether or not to enable the LPF. This item is set to OFF normally.

Vertical or horizontal streak noise may appear on the projected image, depending on the type of the DVD player you use. In such a case, you can reduce such streak noise by enabling the LPF. However, projected images become

softened slightly.

1.Display the SIGNAL menu.

2.Press the or button to select USER.

3.Press the ENTER button.

4.Press the or button to select LPF.

5.Press the or button to choose ON or OFF.

To cancel the menu:

6. Press the MENU button.

?

LPFOFF

EN-30

Image 30
Contents HC3100 When using the projector in Europe EN-2Risk of Electric Shock Do not Open Contents Important safeguards EN-4EN-5 Checking accessories Inserting the batteries into the remote controlPreparing your projector Overview Control area Terminal panelEN-7 Preparing your projector Remote controlUsing the picture quality adjusting buttons Bottom sideReception angle Using the remote controlOperational range of the remote control EN-9Basic setup Setting up your projectorSetting up the screen Adjusting the projection angleTrigger terminal With the Installation menu See page 24 for menu settingTo cancel the menu EN-11Screen size and projection distance Setting up your projectorWhen the aspect ratio of the screen is EN-12Basic home theater system connection Connecting the projector to video equipmentViewing video images EN-13When a TV tuner or VCR is connected Connecting to a video player, etcConnecting to a DVD player or Hdtv decoder Viewing video imagesEN-15 Connection for video equipment having an Hdmi terminalConnection for video equipment having a DVI-D terminal Plugging in the power cord EN-16Projecting images EN-17EN-18 When projected images are distorted to a trapezoidTo stop projecting Following casesWith the remote control Setting the aspect ratioHow to change the settings With the Feature menuViewing computer images Connecting the projector to a computerPlugging the power cord EN-20Projecting images EN-21Viewing computer images When connecting to a notebook computerExample of the setting procedure for external output Auto Position buttonMenu operation EN-23Menu operation How to set the menusAvailable settings in the menus EN-24Installation menu EN-25Feature menu EN-26AV memory EN-27To adjust the color Color and Tint Adjusting projected imagesTo adjust the brightness Contrast and Brightness To sharpen or soften the projected image SharpnessTo adjust the ratio of change in brightness Gamma Mode To adjust the tone of white Color TempAbout color temperature EN-29Adjusting projected images To adjust the vertical positionEN-30 To enable the password function Advanced featuresPassword function To cancel the password functionCleaning Using filterInstallation Cleaning the filterInterval of lamp replacement Replacing the lampEN-33 Replacing the lamp Cleaning of the projector and the ventilation slotsCleaning of the lens To replace the lampTroubleshooting No image appears on the screen ProblemSolutionEN-35 Images are not displayed correctly Problem Solution TroubleshootingNo image appears on the screen Problem Solution EN-36Others Problem Solution EN-37Abnormal condition IndicatorsNormal condition EN-38Dimension drawings unit mm SpecificationsEN-39 Specifications ConnectorsReplacement part Option/not included in the box EN-40Mitsubishi Projector Contact Information