Mitsubishi Electronics EX53U, EX53E user manual Caution To Reduce The Risk Of Electric, Shock

Page 2
CAUTION : TO REDUCE THE RISK OF ELECTRIC

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC

SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsu- lated "dangerous voltage" within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUT- LET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

NOTE:

SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.

WARNING

Use the attached specified power supply cord. If you use another power supply cord, it may cause interference with radio and television reception.

Use the attached RGB cable with this equipment so as to keep inter- ference within the limit of an FCC Class B device. (only for EX53U) This apparatus must be grounded.

DO NOT LOOK DIRECTLY INTO THE LENS WHEN THE PROJECTOR IS IN THE POWER ON MODE.

When using the projector in Europe (only for EX53E):

COMPLIANCE NOTICE

This Projector complies with the requirements of the EC Directive 99/5/EC "R&TTE Directive".

The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on small-scale enterprises, inside as well as outside of the buildings. All places of operation are characterized by their connection to the public low voltage power supply system.

CAUTION

Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75.

The attached power cords are to be used exclusively for this product. Never use them for other products.

WARNING

Use the attached RGB cable with this equipment so as to keep inter- ference within the limits of an EN55022 Class B device.

Please follow WARNING instructions.

Note: This symbol mark is for EU countries only.

This symbol mark is according to the directive 2002/96/EC Article 10 Information for users and Annex IV.

Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and components which can be recycled and reused.

This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from your household waste.

Please, dispose of this equipment at your local community waste collection/recycling centre.

In the European Union there are separate collection systems for used electrical and electronic product.

Please, help us to conserve the environment we live in!

EN-2

Image 2
Contents This User Manual is important to you Please read it before using your projectorMODEL ENGLISHDO NOT REMOVE COVER OR BACK NO USER-SERVICEABLE PARTS INSIDE When using the projector in Europe only for EX53E COMPLIANCE NOTICECAUTION TO REDUCE THE RISK OF ELECTRIC REFER SERVICING TO QUALIFIED SERVICE PERSONNELTrademark, Registered trademark ContentsDeclaration of Conformity Safety instructions for wirelessImportant safeguards Do not unplug the power cord during operation Do not keep using the damaged projectorDo not look into the lens when the projector is operating Do not look into the air outlet grilles when projector is operatingModel Name EX53E Regulatory statement R&TTEModel Name EX53U Terminal board OverviewControl panel Kensington LockBottom side Remote controlOverview continued Operation range of the remote control Remote controlBattery installation Reception angle verticalFront projection InstallationLayout of the projector Front projection, ceiling mountingBasic connections Projector + AV deviceBasic connections continued Projector + DVD player or HDTV decoderFor analog connection Projector + ComputerFor computer with Mini D-SUB or DVI-D For digital connectionUsing the adjustment feet rear Adjustment of the projection angleUsing the adjustment feet front After using the projectorBasic operation Power-onWhen fine streaks are seen on projected images 4 FOCUS 6 ZOOMSetting the aspect ratio Power-offVolume from the speaker How to change the settingsWhen connecting to a laptop computer Wall ScreenSafety instructions for wireless Security measures Security precautions for wirelessAbout wireless LAN network After-sales Service Software license agreement for wirelessInstalling software Precaution for Windows VistaB. Plugging the power code Projecting images wirelesslyA. Connecting the antenna C. Turning the power on and adjusting the focusG. Projecting images Projecting images wirelessly continuedF. Installing the connection software Running the connection softwareIf the wireless connection fails Pausing the projection How to use the connection softwarePausing or resuming the projection Displaying the administration screenDisplaying the version information of the software How to use the connection software continuedDisplaying the information about the projector Downloading the connection software How to use the administration screenConfiguring the projector Selecting the image to be projectedFor the setting items, ask your network administrator How to use the administration screen continuedChanging the network settings 1. Click Network SetupRestoring the default settings Changing the settings for the projectionChanging the password Glossary3. Click the OK button Uninstalling the connection software2. Click the Yes button EN-29How to use wired LAN connection For Ethernet connectionEN-31 Menu operationMenus are not displayed when no signal is supplied to the projector Menu Options Menu operation continuedBasic operation 1. IMAGE menu2. INSTALLATION menu EN-333. FEATURE menu 4. SINGAL menu SIGNAL USER menu5. WIRELESS menu 6. INFORMATION menuTo adjust the brightness CONTRAST and BRIGHT- NESS Image adjustmentAdjusting projected images To adjust the color COLOR and TINTHow to adjust the image supplied from the computer using the menu Image adjustment continuedSimple method to adjust the image position To adjust the horizontal positionPassword function Advanced featuresProcedure To enable the password functionMagnify Advanced features continuedTo cancel the password function To use the MAGNIFY modeLamp replacement When the projector is mounted to the ceilingReset of the lamp operation time Lamp replacement continuedInterval of lamp replacement Problem TroubleshootingNo image appears on the screen SolutionTroubleshooting continued Images are not displayed correctlyThe projector cannot be connected wirelessly OthersCleaning of the lens MaintenanceCleaning of the projector and the ventilation slots To protect the surface of the projector from fading or deterioratingAbnormal condition IndicatorsNormal condition Specifications EN-47Dimensional drawings unit mm Specifications continuedConnectors Replacement partSpecification of RGB signals in each computer mode of the projector 3 Supports a DVI-D terminal1 Zusho Baba, Nagaokakyo-City, Kyoto Japan MITSUBISHI ELECTRIC CORPORATIONMitsubishi Projector Warranty, Sales Support and Service Information
Related manuals
Manual 2 pages 4.76 Kb