Mitsubishi Electronics EX320U-ST user manual Press / to reveal

Page 36

Controlling the projector remotely through a web browser (e-Control™)

Once you have the correct IP address for the projector and the projector is on or in standby state, you can use any computer that is on the same local area network to control the projector.

When using this function, Adobe Flash Player has to be installed in your computer. Please download Adobe Flash Player from the website of Adobe Systems Incorporated.

1.Enter the IP address of the projector in the address bar of your browser and press enter. (for example, http:// 192.168.0.146)

When using an "Opera" browser, add "/index.html" after the IP address. (for example; http://192.168.0.146/index.html)

2.The remote network operation page is displayed. This page allows you to operate the projector as if you were using the remote control or control panel on the projector.

i

iii

i	Press / to reveal
	more buttons.

i.These buttons function the same as the ones on the OSD menus or remote control. See "2. PICTURE menu" on page 43 and "Remote control" on page 9 for details.

ii. To switch input source, click on your desired source.

When you use the projector control panel or remote control to change the OSD menu settings, it may take a while for the web browser to synchronize these changes with the projector.

3.The Tools page allows you to manage the projector, configure the LAN control settings and secure access of remote network operation on this projector.

i

ii

iv

iiiv

vi

i.When using the Crestron Control System, please refer to the user manual of Crestron Control system for setup information.

ii.You can name the projector, keep track of its location and the person in charge of it. This column allows a maximum of 32 single-byte characters.

iii.You can adjust the LAN Control Settings.

EN-36

Image 36

Contents EX320U-ST Shock EN-3 Contents Important safeguards Compliance Notice of Industry Canada Projector exterior view Kensington LockFront/upper side Controls and functions ProjectorRemote control Magnifying and searching for details on page 25 forUsing the remote control for the first time Positioning your projector Choosing a locationWhen fine streaks are seen on projected images Obtaining a preferred projected image sizeEN-13 Layout of the projector Front projectionStandard 169Connecting a computer or monitor Connecting a computerConnection To connect the projector to a notebook or desktop computerConnecting Video source devices Connecting a monitorTo connect the projector to a monitor Connecting an Hdmi device Connecting a Component Video source deviceTo connect the projector to an Hdmi device To connect the projector to a Component Video source deviceConnecting an S-Video source device To connect the projector to an S-Video source deviceConnecting a composite Video source device To connect the projector to a composite Video source deviceOperation Starting up the projectorUsing the menus Basic menuUtilizing the password function Setting a passwordIf you forget the password Entering the password recall procedureSwitching input signal Disabling the password functionChanging Color Space Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityMagnifying and searching for details Correcting keystoneSelecting the aspect ratio About the aspect ratioSelecting a picture mode Picture modes for different types of signalsSetting the User 1/User 2 mode Optimizing the imageFine-tuning the image quality in user modes Using Wall Screen 3D Color ManagementImmediately Setting the presentation timer To cancel the timer, perform the following stepsHow to use the Timer On key? Adjusting the sound Hiding the imageLocking control keys Freezing the imageDirect power off Personalizing the projector menu displayShutting down the projector Standby Audio OutWatching 3D Content L RMode Resolution H x Horizontal Frequency Vertical Frequency Configuring the LAN Control Settings Supervising and controlling by computerIf you are in a Dhcp environment If you are in a non-DHCP environmentPress / to reveal Controlling the projector using PJLink application About PJLinkUtilizing the password function PJLink supported commandsHow to Use Network Function GlossaryMenu operation Menu systemSystem Setup Blank Timer Description of each menu DescriptionSetting Brightness Contrast Color Lamp mode Reset lamp timerMenu display time Menu positionChange password Power on lockClosed Caption Enable SettingMaintenance Care of the projectorSetting Lamp mode as Low Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Spare lamp for EX320U-ST VLT-EX320LPResetting the lamp timer EN-51 Indicators Down without the normal cooling down processProjector needs 90 seconds to cool down Please contact your dealer for assistanceTroubleshooting Specifications Projector specificationsDimensions Timing chartSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Mitsubishi Electric Corporation