Mitsubishi Electronics EX320U-ST user manual How to Use Network Function, Glossary

Page 39


	INF2?	Inquiry about the model name	"EX320U-ST" is returned.	ENGLISH

	INF0?	Inquiry about other information	No other information is available. No parameter is returned.
	INF0?	Inquiry about other information

	CLSS?	Inquiry about the class information	"1" is returned.

•The PJLink "INPT?" will be replied only when the source is displayed on screen. When there is no signal, only "Unavailable Time!" will be answered.

•The above-mentioned control may not be performed correctly or the monitoring data may not be obtained correctly in the following conditions:

•During standby

•During input source switching

•During command processing

•During AUTO execution

•Before the splash screen disappears after the power is turned on.

•Use 1 computer to control/monitor 1 projector.

•For how to control/monitor using PJLink™, see the operation manual of the PJLink™ application you use.

•When you monitor the projector's operating state using this function by issuing inquiry commands successively, issue an inquiry command after receiving the response to the previous inquiry command from the projector.

How to Use Network Function

•When connecting a computer and projector with LAN, configure the both IP Addresses in the same network group.

•Configure the IP CONFIG correctly. If the settings are not correct, the communication may be unavailable. For the detail, consult the network administrator.

When the Control By in the SYSTEM SETUP: Advanced > LAN Control Settings menu is selected RS-232C, the LAN Control Settings function is not available.

Glossary

For more detail of the glossary below, refer to the technical book that is commercially available.

Term	Description
DHCP	Abbreviation for Dynamic Host Confi guration Protocol. This protocol
	automatically assigns IP Address to networked devices.
IP Address	Numerical address to identify networked computers.
Subnet Mask	A numeric value to defi ne the number of bits used for a network
	address of a divided network (or subnet) in an IP Address.
Default Gateway	A server (or router) to communicate across networks (subnets) that
	are divided by Subnet Mask.

MAC Address	Abbreviation for Media Access Control Address. MAC Address is a
	unique ID number assigned to each network adapter. And this is
	based on which data are sent and received between network adapt-
	ers.

EN-39

Image 39

Contents EX320U-ST Shock EN-3 Contents Important safeguards Compliance Notice of Industry Canada Projector exterior view Kensington LockFront/upper side Projector Controls and functionsMagnifying and searching for details on page 25 for Remote controlUsing the remote control for the first time Choosing a location Positioning your projectorObtaining a preferred projected image size When fine streaks are seen on projected imagesEN-13 169 Layout of the projectorFront projection StandardTo connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer ConnectionConnecting Video source devices Connecting a monitorTo connect the projector to a monitor To connect the projector to a Component Video source device Connecting an Hdmi deviceConnecting a Component Video source device To connect the projector to an Hdmi deviceTo connect the projector to an S-Video source device Connecting an S-Video source deviceTo connect the projector to a composite Video source device Connecting a composite Video source deviceStarting up the projector OperationBasic menu Using the menusEntering the password recall procedure Utilizing the password functionSetting a password If you forget the passwordSwitching input signal Disabling the password functionChanging Color Space Fine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Magnifying and searching for detailsAbout the aspect ratio Selecting the aspect ratioOptimizing the image Selecting a picture modePicture modes for different types of signals Setting the User 1/User 2 modeFine-tuning the image quality in user modes Using Wall Screen 3D Color ManagementImmediately Setting the presentation timer To cancel the timer, perform the following stepsHow to use the Timer On key? Freezing the image Adjusting the soundHiding the image Locking control keysStandby Audio Out Direct power offPersonalizing the projector menu display Shutting down the projectorL R Watching 3D ContentMode Resolution H x Horizontal Frequency Vertical Frequency If you are in a non-DHCP environment Configuring the LAN Control SettingsSupervising and controlling by computer If you are in a Dhcp environmentPress / to reveal About PJLink Controlling the projector using PJLink applicationPJLink supported commands Utilizing the password functionGlossary How to Use Network FunctionMenu system Menu operationSystem Setup Blank Timer Description Description of each menuSetting Brightness Contrast Color Menu position Lamp modeReset lamp timer Menu display timeSetting Change passwordPower on lock Closed Caption EnableCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp mode as LowSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampSpare lamp for EX320U-ST VLT-EX320LP Replacing the lampResetting the lamp timer EN-51 Please contact your dealer for assistance IndicatorsDown without the normal cooling down process Projector needs 90 seconds to cool downTroubleshooting Projector specifications SpecificationsTiming chart DimensionsSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Mitsubishi Electric Corporation