Mitsubishi Electronics EX320U-ST user manual Specifications, Projector specifications

Page 54

Specifications

Projector specifications

All specifications are subject to change without notice.

General

Product name	DLP™ Projector
Model name	EX320U-ST

Optical

Resolution	1024 x 768 XGA

Display system	1-CHIP DMD

Lens F/Number	F = 2.6, f = 6.9 mm

Lamp	230 W lamp

Electrical

Power supply	AC100–240V, 50/60 Hz (Automatic)

Power consumption	3.3 A, 330 W (Max), < 1 W (Standby) When setting is:
	Standby Monitor Out: Off
	Standby Audio Out:Off
	LAN Control Settings: Off
Mechanical

Dimensions	282 mm (W) x 92 mm (H) x 229 mm (D) (Not including protrusion)

Weight	2.9 Kg (6 lbs)

Input terminal

Computer input

RGB input	D-Sub 15-pin (female) x 2

Video signal input

S-VIDEO	Mini DIN 4-pin port x 1
VIDEO	RCA jack x 1

SD/HDTV signal input	Analog – D-Sub <–> Component RCA jack x 3
	(through RGB input)
	Digital – HDMI

Audio signal input	PC audio jack x 1 (Share the terminal with computer and video inputs)
Output terminal

RGB output	D-Sub 15-pin (female) x 1
Audio signal output	PC audio jack x 1 (Share the terminal with computer and video inputs)

Speaker output	2W x 1

Control terminal

Serial control	D-Sub 9-pin (Male) x 1

LAN control	RJ-45 x 1
Environmental requirements

Operating temperature	5°C–35°C (without condensation)

Operating relative humidity	30%–90% (without condensation)

EN-54

Image 54

Contents EX320U-ST Shock EN-3 Contents Important safeguards Compliance Notice of Industry Canada Projector exterior view Kensington LockFront/upper side Controls and functions ProjectorRemote control Magnifying and searching for details on page 25 forUsing the remote control for the first time Positioning your projector Choosing a locationWhen fine streaks are seen on projected images Obtaining a preferred projected image sizeEN-13 Standard Layout of the projectorFront projection 169Connection Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computerConnecting Video source devices Connecting a monitorTo connect the projector to a monitor To connect the projector to an Hdmi device Connecting an Hdmi deviceConnecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video source device To connect the projector to an S-Video source deviceConnecting a composite Video source device To connect the projector to a composite Video source deviceOperation Starting up the projectorUsing the menus Basic menuIf you forget the password Utilizing the password functionSetting a password Entering the password recall procedureSwitching input signal Disabling the password functionChanging Color Space Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityMagnifying and searching for details Correcting keystoneSelecting the aspect ratio About the aspect ratioSetting the User 1/User 2 mode Selecting a picture modePicture modes for different types of signals Optimizing the imageFine-tuning the image quality in user modes Using Wall Screen 3D Color ManagementImmediately Setting the presentation timer To cancel the timer, perform the following stepsHow to use the Timer On key? Locking control keys Adjusting the soundHiding the image Freezing the imageShutting down the projector Direct power offPersonalizing the projector menu display Standby Audio OutWatching 3D Content L RMode Resolution H x Horizontal Frequency Vertical Frequency If you are in a Dhcp environment Configuring the LAN Control SettingsSupervising and controlling by computer If you are in a non-DHCP environmentPress / to reveal Controlling the projector using PJLink application About PJLinkUtilizing the password function PJLink supported commandsHow to Use Network Function GlossaryMenu operation Menu systemSystem Setup Blank Timer Description of each menu DescriptionSetting Brightness Contrast Color Menu display time Lamp modeReset lamp timer Menu positionClosed Caption Enable Change passwordPower on lock SettingMaintenance Care of the projectorLamp information Setting Lamp mode as LowSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Spare lamp for EX320U-ST VLT-EX320LPResetting the lamp timer EN-51 Projector needs 90 seconds to cool down IndicatorsDown without the normal cooling down process Please contact your dealer for assistanceTroubleshooting Specifications Projector specificationsDimensions Timing chartSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Mitsubishi Electric Corporation