PLUS Vision U7-137SF, U7-132HSF, U7-132SF user manual Precautions, DOC Compliance Notice

Page 2

IMPORTANT SAFETY INFORMATION

Precautions

Please read this manual carefully before using your PLUS Data Projector and keep the manual handy for future reference.

These operating instructions apply to both models U7-132SF, U7-132hSF and U7-137SF.

The two models have the same display resolution and projection distance, but their CompactFlash (CF) card, wireless LAN card and wired LAN functions differ.

For details, refer to the table below.

These instructions describe the U7-137SF (full-function model).

Model Name

CF card/Wireless LAN card function

Wired LAN function

USB memory function

U7-137SF

￿

￿

￿

U7-132SF

—

—

—

U7-132hSF

—

—

—

Explanations that do not apply to both models are marked

U7-137SF only .

 

CAUTION

TO PREVENT SHOCK, DO NOT OPEN THE CABINET. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PLUS SERVICE PERSONNEL.

This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside of this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

The above cautions are given on the bottom of the product.

WARNING

TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. DO NOT USE THIS UNIT’S GROUNDED PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALL THREE PRONGS CAN BE FULLY INSERTED. DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COM- PONENTS INSIDE. ALL SERVICING MUST BE DONE BY QUALIFIED PLUS SERVICE PERSONNEL.

WARNING

This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

RF Interference

WARNING

The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by PLUS Vision Corp. in this manual. Failure to comply with this government regulation could void your right to operate this equipment.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer- ence when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

You are cautioned that changes or modifications not expressly approved by the party responsible for compli- ance could void your authority to operate the equipment.

DOC Compliance Notice

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regula- tions.

Hg: Lamp in This Product Contains Mercury. Dispose of Lamp According to Local, State or Federal Law.

E-2

Page 1 Page 3
Image 2
Page 1 Page 3
Contents U7-137SF U7 132SF/U7 132hSF Precautions DOC Compliance NoticeCleaning InstallationPower Supply Lamp ReplacementMajor Features Table of Contents Menu Operations Adjustments and SettingsTable of Contents MiscellaneousAudio cable Mini plug, 2 m / 6.6 feet Checking the Supplied AccessoriesPower cable 1.8 m / 5.9 feet Cable pocket Checking the Supplied AccessoriesUSB cable type A, 2 m / 6.6 feet Terminal cover cordNames of the Main Unit Parts Built-in Security SlotStatus indicator E-22 Names of the Remote Control Parts Precautions Handling of the Remote ControlInserting the Batteries Preparing the Remote ControlRemote Control Range Procedure Up to Projecting to the Screen Placement Guide Screen Size and Projection DistanceDVI-D cable Available as an option. Order code Personal Computers with a DVI ConnectorConnections with Personal Computer RGB signal cable Supplied item Personal Computers with a Mini D-Sub 15-Pin ConnectorConnecting Personal Computers and Video Equipment To Output the External Output Signal of a Notebook Computer Manufacturer Model KeyVideo Equipment with S-VIDEO Connectors Connections with Composite SignalsVideo Equipment with Video Connectors Video cable Suppled item Video cable Supplied itemConnections with Component Signals Audio conversion Connections with Audio ConnectorsAudio cable Supplied item AdapterConnections with the RGB OUT Connector Button on main unit Switch on the projector powerOperating This completes the selection of the display language Power Cable Connections and Switching the Power On/OffPress the Enter button to set CursorUnplug the power cable FinishingAdjust the projection image to the screen Adjustment of the Projection ScreenAdjustment of the Projection Screen Zoom ringRaising the projection image Making Adjustments with the AdjustersFocus ring Lowering the projection imageInput Selection Automatic Adjustment of Analog RGBGeneral Operation Press the Cancel button to immediately close the display Cancelling Video and Audio TemporarilyAdjustment of the Volume Freezing a Moving PicturePress the Zoom button to enlarge the image Enlargement of the Image and Video MovementImage can also be moved in the following circumstances Using the Presentation Timer Using the Laser Pointer OperationJOG buttons Connecting the computer and projectorClick button on back Click buttonRS-232C connections Connecting via a LAN U7-137SF onlyControlling the Projector from a Computer CN-2 D-Sub 9-pin sideProtecting the Projector with the Security Lock Canceling the password Input the password using the number buttons 1 toCanceling the password/Changing the password Changing the passwordPress the Select or button to adjust Using the Quick MenuContent of Adjustments and Settings VolumeMenu Operation Method Names and Functions of Buttons Used for Menu OperationsMenu Screen Names and Functions Menu Operation MethodPerforming Menu Operations Menu Display Press the Menu button to display the menuMaking Adjustments/Settings Sub menuSelecting Another Menu Name with Remote Control Operation RGB Menu name Item Name Sub Menu Setup TerminalBrightness / Contrast / Color / Tint / Sharpness Picture Adj. Picture AdjustmentImage Picture Adj. / Fine Picture / H Position / V PositionPosition ResetFine Picture ImageQuick Color Adj Select the preset color modeColor GammaWhite Selection contents at the time of YPbPr inputColor Temp Color SpaceWhite Balance View Personal Computer SignalVideo Signals AspectKeystone Save Vertical Flip / Horizontal FlipKeystone ViewAuto Source SetupAuto Power Off Menu PositionStatus Indicator Lamp ModeSetup Input FormatPresentation Timer To start the timerOn Screen OptionLanguage BackgroundSecurity Lock Network PasswordStartup Screen OptionInfo Factory DefaultLamp Timer Reset StatusInfo Resolution / FrequencyLamp Timer Thermal Protector When an Indicator is Lit or BlinkingIndicator status What you should do Troubleshooting Check the following matters before requesting servicingCleaning the Inside of the Projector CleaningCleaning a Soiled Projector Main Unit Dirty LensReplacing the Lamp Cartridge Remove the lamp cartridge Unplug the power cord Remove the lamp coverReplacing the Lamp Cartridge Mount the lamp cover Reset the Lamp TimerMount the new lamp cartridge Electrical SpecificationsOptical MechanicalTable of Supported Frequencies SignalResolution Frequency Video Digital AnalogCabinet Dimensions 2005
Top Page Image Contents