Microsoft manual 32 PXP43 Motherboard User’s Guide, Power Management Setup

Page 36

32PXP43 Motherboard User’s Guide

Power Management Setup

This page sets up some parameters for system power management operation.

CMOS Setup Utility - Copyright (C) 1985-2008, American Megatrends, Inc.

Power Management Setup

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Help Item

 

 

ACPI Suspend Type

 

S3 (STR)

 

 

 

 

 

 

 

 

Soft-off by PWR-BTTN

 

Instant Off

 

 

 

 

Select the ACPI

 

 

PWRON After PWR-Fail

 

Power Off

 

 

Resume by Ring

 

Disabled

 

 

state used for

 

 

Resume By PCI/PCI-E/Lan PME

 

Disabled

 

 

System Suspend.

 

 

Resume by USB (S3)

 

Disabled

 

 

 

 

 

Resume By PS2 KB (S3)

 

Disabled

 

 

 

 

 

Resume By PS2 MS (S3)

 

Disabled

 

 

 

 

 

Resume on RTC Alarm

 

Disabled

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

mn< >

:Move Enter : Select

+/-/: Value

F10: Save

ESC: Exit

 

 

 

F1: General Help

F9: Load Default settings

 

 

ACPI Suspend Type (S3)

Use this item to define how your system suspends. In the default, S3, the suspend mode is a suspend to RAM, i.e, the system shuts down with the exception of a refresh current to the system memory.

Soft-off by PWR-BTTN (Instant off)

Under ACPI (Advanced Configuration and Power management Interface) you can create a software power down. In a software power down, the system can be resumed by Wake Up Alarms. This item lets you install a software power down that is con- trolled by the power button on your system. If the item is set to Instant-Off, then the power button causes a software power down. If the item is set to Delay 4 Sec, then you have to hold the power button down for four seconds to cause a software power down.

PWRON After PWR-Fail (Power Off)

This item enables your computer to power off, automatically restart or return to its previous status after abnormal power lost.

Resume By Ring (Disabled)

The system can be turned off with a software command. If you enable this item, the system can automatically resume if there is an incoming call on the Modem. You must use an ATX power supply in order to use this feature.

Resume By PCI/PCI-E/Lan PME (Disabled)

The system can be turned off with a software command. If you enable this item, the system can automatically resume if there is an incoming call on the PCI Modem or PCI LAN card. You must use an ATX power supply in order to use this feature. Use this item to do wake-up action if inserting the PCI card.

Resume By USB (S3) (Disabled)

This item allows you to enable/disable the USB device wakeup function from S3 mode.

Using BIOS

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Preface PXP43 Motherboard User’s GuideIi PXP43 Motherboard User’s Guide Table of Contents Software Setup Introduction Feature ProcessorOnboard LAN Atheros AR8121 PCI-E Gbit LAN Motherboard Components Introducing the Motherboard Table of Motherboard ComponentsSafety Precautions Installing the Motherboard in a CaseChoosing a Computer Case Checking Jumper Settings Setting JumpersChecking Jumper Settings Jumper SettingsInstalling Hardware Installing the ProcessorCPU Installation Procedure 10 PXP43 Motherboard User’s GuideInstalling Memory Modules DDR2 Sdram memory module table12 PXP43 Motherboard User’s Guide Table a DDR2 memory module QVL Qualified Vendor ListInstalling Add-on Cards Expansion Slots14 PXP43 Motherboard User’s Guide Connecting Optional Devices Faudio Front Panel Audio headerSpdifo Spdif out header SATA1~6 Serial ATA connectors Cdin Analog Audio Input connector16 PXP43 Motherboard User’s Guide FUSB1~4 Front Panel USB headersInstalling a Hard Disk Drive/CD-ROM/SATA Hard Drive About Sata ConnectorsInstalling Serial ATA Hard Drives About IDE Devices18 PXP43 Motherboard User’s Guide Connecting I/O Devices Connecting Case Components Connecting 24-pin power cableConnecting 4-pin power cable 20 PXP43 Motherboard User’s GuideCPUFAN1/SYSFAN1 Cooling FAN Power Connector Casefan Case cooling FAN Power ConnectorAtxpower ATX 24-pin Power Connector ATX12V ATX 12V Power Connector22 PXP43 Motherboard User’s Guide Front Panel HeaderAbout the Setup Utility Standard ConfigurationEntering the Setup Utility Bios Navigation Keys 24 PXP43 Motherboard User’s GuideUsing Bios Updating the BiosStandard Cmos Setup 26 PXP43 Motherboard User’s GuideDate & Time SATA1~6/PATA MASTER/SLAVEIDE BusMaster Enabled Type AutoAdvanced Setup Thermal Management EnabledIntel Virtualization Technol Enabled 28 PXP43 Motherboard User’s GuideBoot Up Numlock Status on Apic Mode Enabled1st/2nd/3rd Boot Device CD/DVD/Hard Drive/Remvable Dev Boot Other Device YesAdvanced Chipset Setup Hpet EnabledIntel Robson Enabled 30 PXP43 Motherboard User’s GuideIntegrated Peripherals Power Management Setup 32 PXP43 Motherboard User’s GuidePCI / PnP Setup Resume By PS2 KB S3 DisabledResume By PS2 MS S3 Disabled Resume on RTC Alarm Disabled34 PXP43 Motherboard User’s Guide PC Health StatusSmart Fan Function System Component Characteristics CPU Frequency Setting 333MHzFrequency/Voltage Control Manufacturer IntelOver-clocking Function. Disabled Auto Detect DIMM/PCI Clk Enabled36 PXP43 Motherboard User’s Guide CPU Voltage NormalSupervisor Password Supervisor Password Not InstalledChange Supervisor Password Press Enter User Password Save & Exit Setup38 PXP43 Motherboard User’s Guide Exit Without SavingSoftware Setup Software SetupFor Windows Vista 64bir Driver For Windows Vista Driver For Windows XP 64bir Driver Software Setup
Top Page Image Contents