Microsoft mainboard, K7S5A manual Advanced Setup

Page 28

Advanced Setup Page

Use this page to set more advanced information about your system. Take some care with this page. Making changes can affect the operation of your computer.

AMIBIOS SETUP – ADVANCED SETUP

(C) 2000 American Megatrends, Inc. All Rights Reserved

Quick Boot

Enabled

1st Boot Device

IDE-0

2nd Boot Device

Floppy

3rd Boot Device

CDROM

Try Other Boot Devices

Yes

S.M.A.R.T. for Hard Disks

Disabled

BootUp Num-Lock

On

Floppy Drive Swap

Disabled

Floppy Drive Seek

Disabled

Password Check

Setup

Boot To OS/2 > 64MB

No

L1 Cache

Enabled

L2 Cache

Enabled

System BIOS Cacheable

Enabled

Timing Setting Mode

Normal

SDR/DDR CAS Latency

SPD

Auto Detect DIMM/PCI Clk

Disabled

Clk Gen Spread Spectrum

Disabled

ESC

: Quit

− ↓←→ : Select Item

F1

: Help

PU/PD/+/ -

: Modify

F5

: Old Values

(Shift)F2

: Color

F6

: Load BIOS Defaults

 

F7

: Load Setup Defaults

 

Quick Boot

If you enable this item, the system starts up more quickly be elimination some of the power on test routines.

1st Boot Device/ 2nd Boot Device/ 3rd Boot Device

Use these items to determine the device order the computer uses to look for an operating system to load at start-up time.

Try Other Boot Device

If you enable this item, the system will also search for other boot devices if it fails to find an operating system from the first two locations.

S.M.A.R.T. for Hard Disks

Enable this item if any IDE hard disks support the S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) feature.

BootUp Num-Lock

This item determines if the Num Lock key is active or inactive at system start- up time.

Floppy Drive Swap

If you have two diskette drives installed and you enable this item, drive A be- comes drive B and drive B becomes drive A.

24

Image 28
Contents Preface CopyrightDeclaration of Conformity Table of Contents Using the Mainboard Software Introducing the Mainboard Introduction ChecklistStandard Items Features SchemeChoosing a Computer Case ROMMainboard Components Installing the Mainboard Safety Precautions Quick GuideChecking Jumper Settings Installing the Mainboard in a CaseSetting Jumpers Checking Jumper Settings Jumper SettingsSPK1 Speaker Connector Connecting Case ComponentsJP2 Onboard LAN LED Connections FPI Connector Installing Hardware Installing the ProcessorBefore installing the Processor CPU Installation ProcedureInstalling Memory Modules Follow these instructions to install the CPUInstallation Procedure DDR Sdram ModuleInstalling a Hard Disk Drive/CD-ROM Installing a Hard Disk DriveAbout IDE Devices About UltraDMAInstalling a Floppy Diskette Drive Installing a CD-ROM/DVD DriveInstalling Add-on Cards Follow these instructions to install an add-on cardConnecting Optional Devices FPAUD1O Front panel MIC/Speaker Out header USB1 Extended USB headerWOL1 Wake On LAN Connecting I/O DevicesIR1 Infrared port External Connector Color Coding LPT1This concludes . The next chapter covers the Bios Using Bios About the Setup Utility Standard ConfigurationRunning the Setup Utility Using BiosBios Navigation Keys Amibios Simple Setup Utility VersionStandard Cmos Features Date & TimePri Master/Pri Slave/Sec Master/Sec Slave Floppy Drive A/Floppy Drive BAdvanced Setup Password Check Boot to OS/2 64MBSystem Bios Cacheable Timing Setting ModePower Management Setup PCI / Plug and Play Setup Load Best Performance Settings Load Optimal SettingsFeatures Setup Parallel Port Mode Onboard Parallel PortParallel Port IRQ Parallel Port DMACPU PnP Setup CPU Brand/Type/ Core Voltage/Ratio /FrequencyCPU Speed Dram FrequencyHardware Monitor System / CPU TemperatureVoltage Measurements & FAN Speeds Change or Remove the Password Change PasswordExit Using the Mainboard Software About the Software CD-ROM Auto-installing under WindowsApplication Tab Setup TabRead Me Tab Running Setup Manual Installation Utility Software Reference AMI Flash Memory UtilityWinFlash Utility MediaRing Talk Telephony SoftwareRecovery Genius CD GhostLanguage Genius PageABC