Mitsumi electronic XD206U user manual Installation, Layout of the projector, Front projection

Page 9

Installation

Layout of the projector

Image size varies depending on the distance between the screen and the projector.

Front projection

 

 

 

 

W

 

 

 

 

 

 

 

 

 

 

 

A

B

 

 

 

 

 

 

 

 

 

 

 

A=B

 

 

 

 

 

 

Hd

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

L : Between the screen and the front edge of the projector

 

 

 

 

 

 

 

 

Hd : Height of the projected image

 

 

 

 

 

 

Screen

 

 

 

 

Distance from the screen : L

 

 

Hd

Diagonal size

Width : W

 

Height : H

 

Shortest (Wide)

Longest (Tele)

 

 

 

 

 

inch

cm

inch

cm

inch

cm

inch

m

inch

m

inch

cm

40

102

32

81

24

61

54

1.4

63

1.6

3.5

8.8

60

152

48

122

36

91

82

2.1

95

2.4

5.2

13.3

80

203

64

163

48

122

109

2.8

127

3.2

7.0

17.7

100

254

80

203

60

152

137

3.5

160

4.1

8.7

22.1

150

381

120

305

90

229

206

5.2

240

6.1

13.0

33.1

200

508

160

406

120

305

275

7.0

320

8.1

17.4

44.2

250

635

200

508

150

381

344

8.7

400

10.2

21.7

55.2

300

762

240

610

180

457

413

10.5

-

-

26.1

66.3

The above figures are approximate and may be slightly different from the actual measurements.

ENGLISH

Front projection, ceiling mounting

For ceiling mounting, you need the ceiling mount kit designed for this projector. Ask a specialist for installation.

For details, consult your dealer.

The warranty on this projector does not cover any damage caused by use of any non-recommended ceiling mount kit or installation of the ceiling mount kit in an improper location.

When using the projector mounted on the ceiling, set IMAGE REVERSE in the INSTALLATION menu to MIRROR INVERT. See page 16.

When the projector is mounted on the ceiling, images may appear darker than those projected in the case of tabletop mounting. This isn’t a product malfunction.

Rear projection

Ask a specialist for installation. For details, consult your dealer.

Caution:

Placing the projector directly on a carpet impairs ventilation by the fans, causing damage or failure. Put a hard board under the pro- jector to facilitate ventilation.

Place the projector at least 50 cm (or 20 inch) away from the wall to prevent the air inlet grille and the air outlet grilles that emit hot air from being blocked.

Do not use the projector in the following locations and manners, which may cause fire or electric shock.

In a dusty or humid place.

In a sideways or upside-down position.

Near a heater.

In an oily, smoky, or damp place such as a kitchen.

In direct sunlight.

Where the temperature rises high, such as in a closed car.

Where the temperature is lower than +41ºF (or +5ºC) or higher than +95ºF (or +35ºC ).

If you move the zoom, the screen will be out of focus. If this is the case, adjust the focus again.

Important:

Do not apply force to the lens, because the lens may be damaged.

For rear projection, set IMAGE REVERSE in the INSTALLATION menu to MIRROR. See page 16.

EN-9

Image 9
Contents XD206U Shock When using the projector in EuropeContents Important safeguards Do not look into the lens when the projector is operat- ing Do not keep using the damaged projectorDo not unplug the power cord during operation Place of installationControl panel Terminal board OverviewLamp cover Adjustment feet front Bottom side Remote controlRemote control Battery installationOperation range of the remote control Layout of the projector InstallationFront projection Front projection, ceiling mountingBasic connections Projector + AV deviceProjector + DVD player or Hdtv decoder Projector + Computer For computer with Mini D-SUBFor Macintosh After using the projector Adjustment of the projection anglePreparation Preparation for projectionBasic operation Power-onVolume from the speaker Power-offAnamorphic mode Instant Shut DownBasic operation Menu operationMenu operation Signal Image adjustment Image adjustmentColor temperature Simple adjustment method Adjustment of the image from the computerWhen the image flickers or the image is out of focus To move the image horizontallyStill Advanced featureTo resume the motion in the image Page-up and page-downPassword function To cancel the password functionTo enable the password function Lamp replacement Reset of the lamp operation timeInterval of lamp replacement Images aren’t projected on the screen TroubleshootingImages aren’t projected correctly TroubleshootingCleaning of the projector and the ventilation slots MaintenanceCleaning of the lens OthersIndicators Normal conditionAbnormal condition Kensington Lock SpecificationsDimensional drawings unit mm ConnectorsReplacement part What’s included in the boxEN-29 Mitsubishi Projector Contact Information