Optoma Technology EP7155 manual Environmental Considerations, Power Safety, Replacing the Lamp

Page 4
Environmental Considerations

Usage Notice

Environmental Considerations

A. Temperatures:

Operating: 5 ~ 40 °C

 

Non-operation: -10°C ~ 60°C

B. Humidity:

Operating: 5% to 85%

 

Non-Operation: 5% to 95%

Power Safety

Only use the supplied power cord.

Do not place anything on the power cord. Place the power cord where it will not be in the way of foot traffic.

Remove the batteries from the remote control when storing or not in use for a prolonged period.

Replacing the Lamp

Replacing the lamp can be hazardous if done incorrectly. Refer to “Replacing the Projection Lamp” on page 41 for clear and safe instructions for this procedure. Before replacing the lamp:

Unplug the power cord.

Allow the lamp to cool for about one hour.

Important Recycle Instructions:

Lamp(s) inside this product contain mercury. This product may contain other electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. For

lamp specific disposal information check WWW.LAMPRECYCLE.ORG.

This symbol found on your product or on its packaging, indicates that this product should not be treated as household waste when you wish to dispose of it. Instead, it should be handed over to an applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences to the environment and human health, which could otherwise be caused by inappropriate disposal of this product. The recycling of materials will help to conserve natural resources. This symbol is only valid in the European Union. If you wish to discard this product, please contact your local authorities or dealer and ask

for the correct method of disposal.

Cleaning the Projector

Unplug the power cord before cleaning. Refer to “Cleaning the Projector” on page 45. Allow the lamp to cool for about one hour.

Regulatory Warnings

Before installing and using the projector, read the regulatory notices in the “Regulatory Compliance” sec- tion on page 58.

4

Image 4
Contents Table of Contents Table of ContentsSetup and Operation Menu SettingSpecifications Table of ContentsRegulatory Compliance Precautions Remote ControlGeneral Safety Information Usage NoticePower Safety Cleaning the ProjectorEnvironmental Considerations Replacing the LampMain Features About this manualIntroduction Packing ChecklistAvoid using the projector in dusty environments Front-right View Views of ProjectorTop view-On-screen Display OSD buttons and LEDs Rear view Bottom view Remote Control Transmits signals to projectorLights when the remote control is used Up arrow when connected through USB to a PCIntroduction Remote Control Operating Range Projector and Remote Control Buttons1. Only use AAA batteries Alkaline battery is preferred Inserting the Remote Control Batteries2. Dispose of used batteries according to local ordinance regulations Setup and Operation Connecting Input DevicesStarting and Shutting down the Projector Setting an Access Password Security Lock 3. Press to select Security 6. To change a password, enter the previ- ous password when prompted Adjusting the Projector Level The projector table or stand should be level and sturdyPosition the projector so that it is perpendicular to the screen Ensure the cables are in a safe location. You could trip over themAdjusting the Zoom, Focus and Keystone Adjusting the Volume4. Use the Image-zoom 7. Use the Keystone but- ton to correct image distortionNavigating the OSD OSD Menu ControlsSetting the OSD Language 4. Press Enter to select your language and then click Exit 5. Press Menu to close the OSDMenu Setting OSD Menu OverviewOSD Sub-Menu Overview Image Menu Color Setting Advanced Image Menu Functions Available for Input Sources Brilliant ColorSaturation DegammaDisplay Menu WXGA XGA Signal Display Menu Functions Available for Connected SourceSetup Menu The Setup menu functions are available to all video sources繁體中文 Language简体中文 Capture Security Timer MonthSet the number of months the projector can be used Set the number of days for the projector to be activeOptions Menu Press Enter to open the OPTIONS/Lamp Setting menuPage Lamp Setting Appendices Replacing the Projection Lamp1. Loosen the two cap- tive screws on the lamp compartment cover A. Remove the lamp compartment cover B2. Remove the two screws from the lamp module A Appendices3. Lift the module handle up B 4. Pull firmly on the module handle to re- move the lamp module 5. Reverse steps 1 to 5 to replace the new lamp moduleResetting the Lamp Cleaning the Projector Using the Kensington Lock1. Wipe off dust with a clean dampened cloth 2. Lightly wipe the lens in a circular motionCommon problems and solutions Tips for TroubleshootingLED Error Messages ERROR CODE MESSAGEPOWER LED/FLASHES LAMP LED/FLASHESImage Problems Lamp ProblemsProblem No image appears on the screen Problem The image is blurredRemote Control Problems Audio ProblemsProblem The projector does not respond to the remote control Problem There is no soundHaving the Projector Serviced Service services@optoma.comService services@optoma.com.tw Service service@tsc-europe.comService info@optoma.no Service info@optoma.deScandinavia Latin AmericaSpecifications Projection Distance V.S. Projection SizeShaded rows are equivalent measurement in feet and inches Max. Screen Size WideTiming Mode Table SIGNALRESOLUTION WXGARATE HZ Macbookcompatibility Mac book ProG5 compatibility Power MacG4 compatibility 33.8 HDTV28.1 60.0Projector Dimensions 220 mm8.6 inches71 mm 2.7 inches 178 mm 7 inchesSafety Certifications Regulatory ComplianceFCC Warning CanadaCopyright Disclaimer
Related manuals
Manual 2 pages 3.1 Kb