Optoma Technology EP7155 manual Top view-On-screen Display OSD buttons and LEDs, Introduction

Page 8
Top view—On-screen Display (OSD) buttons and LEDs

Introduction

Top view—On-screen Display (OSD) buttons and LEDs

ITEM

LABEL

 

DESCRIPTION

 

SEE PAGE:

 

 

 

 

 

 

1.

Power

Turns the projector On or Off

 

16

 

 

 

 

 

 

2.

◄/Source

Select the input device

 

 

(Left arrow)

Navigates and changes settings in the OSD

 

 

 

 

 

 

3.

Power LED

Green

Unit is powered on and working correctly

 

 

 

Flashing

Unit is on stand-by/cooling down

 

 

 

Green

 

 

 

 

 

Off

Unit is powered off

 

 

 

 

 

 

4.

Lamp LED

On

Lamp not ready—do not press the power button

 

 

 

Off

Lamp is in normal state

 

5.

Temp LED

On

System over temperature

 

 

 

Off

Normal state

 

6.

AV-Mute

Display blank and audio mute

 

 

 

 

 

7.

Enter

Enter key for the OSD menu

 

 

 

 

 

8.

▲/Keystone+

Corrects image-trapezoid (wider bottom) effect

 

21

 

(Up arrow)

Navigates and changes settings in the OSD

 

 

 

 

 

 

 

9.

►/Re-Sync

Re-Sync VGA source, adjusts phase, tracking, size, position

 

 

(Right arrow)

Navigates and changes settings in the OSD

 

 

 

 

 

10.

▼/Keystone -

Corrects image-trapezoid (wider top) effect

 

21

 

(Down arrow)

Navigates and changes settings in the OSD

 

 

11.

Menu

To switch OSD menu On or Off

 

 

 

 

 

 

 

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Table of Contents Table of ContentsSetup and Operation Menu SettingRegulatory Compliance Table of ContentsSpecifications Precautions Remote ControlGeneral Safety Information Usage NoticePower Safety Cleaning the ProjectorEnvironmental Considerations Replacing the LampMain Features About this manualAvoid using the projector in dusty environments Packing ChecklistIntroduction Front-right View Views of ProjectorTop view-On-screen Display OSD buttons and LEDs Rear view Bottom view Remote Control Transmits signals to projectorLights when the remote control is used Up arrow when connected through USB to a PCIntroduction Remote Control Operating Range Projector and Remote Control Buttons2. Dispose of used batteries according to local ordinance regulations Inserting the Remote Control Batteries1. Only use AAA batteries Alkaline battery is preferred Setup and Operation Connecting Input DevicesStarting and Shutting down the Projector Setting an Access Password Security Lock 3. Press to select Security 6. To change a password, enter the previ- ous password when prompted Adjusting the Projector Level The projector table or stand should be level and sturdyPosition the projector so that it is perpendicular to the screen Ensure the cables are in a safe location. You could trip over themAdjusting the Zoom, Focus and Keystone Adjusting the Volume4. Use the Image-zoom 7. Use the Keystone but- ton to correct image distortionNavigating the OSD OSD Menu ControlsSetting the OSD Language 4. Press Enter to select your language and then click Exit 5. Press Menu to close the OSDMenu Setting OSD Menu OverviewOSD Sub-Menu Overview Image Menu Color Setting Advanced Image Menu Functions Available for Input Sources Brilliant ColorSaturation DegammaDisplay Menu WXGA XGA Signal Display Menu Functions Available for Connected SourceSetup Menu The Setup menu functions are available to all video sources简体中文 Language繁體中文 Capture Security Timer MonthSet the number of months the projector can be used Set the number of days for the projector to be activeOptions Menu Press Enter to open the OPTIONS/Lamp Setting menuPage Lamp Setting Appendices Replacing the Projection Lamp1. Loosen the two cap- tive screws on the lamp compartment cover A. Remove the lamp compartment cover B3. Lift the module handle up B Appendices2. Remove the two screws from the lamp module A 4. Pull firmly on the module handle to re- move the lamp module 5. Reverse steps 1 to 5 to replace the new lamp moduleResetting the Lamp Cleaning the Projector Using the Kensington Lock1. Wipe off dust with a clean dampened cloth 2. Lightly wipe the lens in a circular motionCommon problems and solutions Tips for TroubleshootingLED Error Messages ERROR CODE MESSAGEPOWER LED/FLASHES LAMP LED/FLASHESImage Problems Lamp ProblemsProblem No image appears on the screen Problem The image is blurredRemote Control Problems Audio ProblemsProblem The projector does not respond to the remote control Problem There is no soundHaving the Projector Serviced Service services@optoma.comService services@optoma.com.tw Service service@tsc-europe.comService info@optoma.no Service info@optoma.deScandinavia Latin AmericaSpecifications Projection Distance V.S. Projection SizeShaded rows are equivalent measurement in feet and inches Max. Screen Size WideTiming Mode Table SIGNALRESOLUTION WXGARATE HZ Macbookcompatibility Mac book ProG4 compatibility Power MacG5 compatibility 33.8 HDTV28.1 60.0Projector Dimensions 220 mm8.6 inches71 mm 2.7 inches 178 mm 7 inchesSafety Certifications Regulatory ComplianceFCC Warning CanadaCopyright Disclaimer
Related manuals
Manual 2 pages 3.1 Kb
Top Page Image Contents