Optoma Technology EP7155 manual Cleaning the Projector, Using the Kensington Lock, Appendices

Page 45
Cleaning the Projector

Appendices

Cleaning the Projector

Cleaning the projector to remove dust and grime will help ensure trouble-free operation.

Warning:

1.Be sure to turn off and unplug the projector at least an hour before cleaning. Failure to do so could result in a severe burn.

2.Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings on the projector.

3.If a little water gets into the projector interior while cleaning, leave unplugged in a well-ventilated room for several hours before using.

4.If a lot of water gets into the projector interior when cleaning, have the projector serviced.

Cleaning the Lens

You can purchase optic lens cleaner from most camera stores. Refer to the following to clean the pro- jector lens.

1.Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to the lens.)

2.Lightly wipe the lens in a circular motion.

Caution:

1.Do not use abrasive cleaners or solvents.

2.To prevent discoloration or fading, avoid getting cleaner on the projector case.

Cleaning the Case

Refer to the following to clean the projector case.

1.Wipe off dust with a clean dampened cloth.

2.Moisten the cloth with warm water and mild detergent (such as used to wash dishes), and then wipe the case.

3.Rinse all detergent from the cloth and wipe the projector again.

Caution:

To prevent discoloration or fading of the case, do not use abrasive alcohol-based cleaners.

Using the Kensington® Lock

If you are concerned about security, attach the projector to a permanent object with the Kensington slot and a security cable.

45

Image 45
Contents Table of Contents Table of ContentsSetup and Operation Menu SettingTable of Contents SpecificationsRegulatory Compliance Remote Control PrecautionsGeneral Safety Information Usage NoticeCleaning the Projector Power SafetyEnvironmental Considerations Replacing the LampAbout this manual Main FeaturesPacking Checklist IntroductionAvoid using the projector in dusty environments Views of Projector Front-right ViewTop view-On-screen Display OSD buttons and LEDs Rear view Bottom view Transmits signals to projector Remote ControlLights when the remote control is used Up arrow when connected through USB to a PCIntroduction Projector and Remote Control Buttons Remote Control Operating RangeInserting the Remote Control Batteries 1. Only use AAA batteries Alkaline battery is preferred2. Dispose of used batteries according to local ordinance regulations Connecting Input Devices Setup and OperationStarting and Shutting down the Projector Setting an Access Password Security Lock 3. Press to select Security 6. To change a password, enter the previ- ous password when prompted The projector table or stand should be level and sturdy Adjusting the Projector LevelPosition the projector so that it is perpendicular to the screen Ensure the cables are in a safe location. You could trip over themAdjusting the Volume Adjusting the Zoom, Focus and Keystone4. Use the Image-zoom 7. Use the Keystone but- ton to correct image distortionOSD Menu Controls Navigating the OSDSetting the OSD Language 5. Press Menu to close the OSD 4. Press Enter to select your language and then click ExitOSD Menu Overview Menu SettingOSD Sub-Menu Overview Image Menu Color Setting Advanced Brilliant Color Image Menu Functions Available for Input SourcesSaturation DegammaDisplay Menu WXGA XGA Display Menu Functions Available for Connected Source SignalThe Setup menu functions are available to all video sources Setup MenuLanguage 繁體中文简体中文 Capture Month Security TimerSet the number of months the projector can be used Set the number of days for the projector to be activePress Enter to open the OPTIONS/Lamp Setting menu Options MenuPage Lamp Setting Replacing the Projection Lamp Appendices1. Loosen the two cap- tive screws on the lamp compartment cover A. Remove the lamp compartment cover BAppendices 2. Remove the two screws from the lamp module A3. Lift the module handle up B 5. Reverse steps 1 to 5 to replace the new lamp module 4. Pull firmly on the module handle to re- move the lamp moduleResetting the Lamp Using the Kensington Lock Cleaning the Projector1. Wipe off dust with a clean dampened cloth 2. Lightly wipe the lens in a circular motionTips for Troubleshooting Common problems and solutionsERROR CODE MESSAGE LED Error MessagesPOWER LED/FLASHES LAMP LED/FLASHESLamp Problems Image ProblemsProblem No image appears on the screen Problem The image is blurredAudio Problems Remote Control ProblemsProblem The projector does not respond to the remote control Problem There is no soundService services@optoma.com Having the Projector ServicedService services@optoma.com.tw Service service@tsc-europe.comService info@optoma.de Service info@optoma.noScandinavia Latin AmericaProjection Distance V.S. Projection Size SpecificationsShaded rows are equivalent measurement in feet and inches Max. Screen Size WideSIGNAL Timing Mode TableRESOLUTION WXGAMacbook RATE HZcompatibility Mac book ProPower Mac G5 compatibilityG4 compatibility HDTV 33.828.1 60.0220 mm8.6 inches Projector Dimensions71 mm 2.7 inches 178 mm 7 inchesRegulatory Compliance Safety CertificationsFCC Warning CanadaDisclaimer Copyright
Related manuals
Manual 2 pages 3.1 Kb