Optoma Technology EP7155 Usage Notice, Precautions, Remote Control, General Safety Information

Page 3
Usage Notice

Usage Notice

Congratulations and thank you for choosing an Optoma DLP projector.

Important:

It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years of safe use of the projector. Keep this manual for future reference.

Precautions

Warning symbols are used on the unit and in this manual to alert you of hazardous situations. The following styles are used in this manual to alert you to important information.

Note:

Provides additional information on the topic at hand.

Important:

Provides additional information that should not be overlooked.

Caution:

Alerts you to situations that may damage the unit.

Warning:

Alerts you to situations that may damage the unit, create a hazardous environment, or cause per- sonal injury.

Throughout this manual, component parts and items in the OSD menus are denoted in bold font as in this example:

“Push the Menu button on the remote control to open the Main menu.”

Remote Control

Some remote controls have a laser for pointing out items on a screen.

DANGER: Do not point the laser in the eyes. Doing so can damage the eyes permanently.

General Safety Information

Do not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in the unit. For servicing, contact qualified service personnel.

Follow all warnings and cautions in this manual and on the unit case.

The projection lamp is extremely bright by design. To avoid damage to eyes, do not look into the lens when the lamp is on.

Do not place the unit on an unstable surface, cart, or stand.

Avoid using the system near water, in direct sunlight, or near a heating device. Do not place heavy objects such as books or bags on the unit.

Remove the lens cap to avoid high temperature damage and bad odor when the projector is switched on.

3

Image 3
Contents Menu Setting Table of ContentsTable of Contents Setup and OperationTable of Contents SpecificationsRegulatory Compliance Usage Notice PrecautionsRemote Control General Safety InformationReplacing the Lamp Power SafetyCleaning the Projector Environmental ConsiderationsAbout this manual Main FeaturesPacking Checklist IntroductionAvoid using the projector in dusty environments Views of Projector Front-right ViewTop view-On-screen Display OSD buttons and LEDs Rear view Bottom view Up arrow when connected through USB to a PC Remote ControlTransmits signals to projector Lights when the remote control is usedIntroduction Projector and Remote Control Buttons Remote Control Operating RangeInserting the Remote Control Batteries 1. Only use AAA batteries Alkaline battery is preferred2. Dispose of used batteries according to local ordinance regulations Connecting Input Devices Setup and OperationStarting and Shutting down the Projector Setting an Access Password Security Lock 3. Press to select Security 6. To change a password, enter the previ- ous password when prompted Ensure the cables are in a safe location. You could trip over them Adjusting the Projector LevelThe projector table or stand should be level and sturdy Position the projector so that it is perpendicular to the screen7. Use the Keystone but- ton to correct image distortion Adjusting the Zoom, Focus and KeystoneAdjusting the Volume 4. Use the Image-zoomOSD Menu Controls Navigating the OSDSetting the OSD Language 5. Press Menu to close the OSD 4. Press Enter to select your language and then click ExitOSD Menu Overview Menu SettingOSD Sub-Menu Overview Image Menu Color Setting Advanced Degamma Image Menu Functions Available for Input SourcesBrilliant Color SaturationDisplay Menu WXGA XGA Display Menu Functions Available for Connected Source SignalThe Setup menu functions are available to all video sources Setup MenuLanguage 繁體中文简体中文 Capture Set the number of days for the projector to be active Security TimerMonth Set the number of months the projector can be usedPress Enter to open the OPTIONS/Lamp Setting menu Options MenuPage Lamp Setting cover A. Remove the lamp compartment cover B AppendicesReplacing the Projection Lamp 1. Loosen the two cap- tive screws on the lamp compartmentAppendices 2. Remove the two screws from the lamp module A3. Lift the module handle up B 5. Reverse steps 1 to 5 to replace the new lamp module 4. Pull firmly on the module handle to re- move the lamp moduleResetting the Lamp 2. Lightly wipe the lens in a circular motion Cleaning the ProjectorUsing the Kensington Lock 1. Wipe off dust with a clean dampened clothTips for Troubleshooting Common problems and solutionsLAMP LED/FLASHES LED Error MessagesERROR CODE MESSAGE POWER LED/FLASHESProblem The image is blurred Image ProblemsLamp Problems Problem No image appears on the screenProblem There is no sound Remote Control ProblemsAudio Problems Problem The projector does not respond to the remote controlService service@tsc-europe.com Having the Projector ServicedService services@optoma.com Service services@optoma.com.twLatin America Service info@optoma.noService info@optoma.de ScandinaviaMax. Screen Size Wide SpecificationsProjection Distance V.S. Projection Size Shaded rows are equivalent measurement in feet and inchesWXGA Timing Mode TableSIGNAL RESOLUTIONMac book Pro RATE HZMacbook compatibilityPower Mac G5 compatibilityG4 compatibility 60.0 33.8HDTV 28.1178 mm 7 inches Projector Dimensions220 mm8.6 inches 71 mm 2.7 inchesCanada Safety CertificationsRegulatory Compliance FCC WarningDisclaimer Copyright
Related manuals
Manual 2 pages 3.1 Kb