Marantz RX9001 manual Firmware Update, Operating A/V components with the Extender

Page 16

RX9001 User Guide

Operating A/V components with the Extender

The A/V components do not respond to commands from the Extender

•Check if the Busy LED blinks green when you send a command with the Control Panel. If the Busy LED does not blink, the Extender is not receiving commands from a Control Panel.

•Make sure that the Control Panel is configured correctly in Wizz.it Ex;

•Make sure that the Extender is configured correctly in the Configuration Tool and connected properly to the A/V components;

•Make sure that the switches on the Extender are set correctly.

There are duplicate Extender IDs

Using the Extender ID switch, assign a unique ID to each Extender in the same Wireless Network. Make sure the Control Panel is configured accordingly in Wizz.it Ex.

You can use up to 16 different Extenders in the same Wireless Network.

Resetting the Extender

This is only necessary when the Extender shows unusual behavior.

To perform a reset, unplug the power adapter from the Extender. Wait a few seconds, and plug it in again.

Firmware Update

When an update of the Extender firmware is available, this will be announced on the Marantz website: http://www.marantz.com (in the Home Entertainment section of your region).

Note You can always see the current version of the firmware in the Configuration Tool.

1Download the new version of the firmware on the PC and save it in the desired location.

2Unplug the Extender. You can now update it in one of the ways described below.

Updating the Extender with the Configuration Cable

1Connect the Extender to the PC with the configuration cable (this is the crossed Ethernet cable enclosed).

2Make sure that the PC is switched to DHCP while the Extender is in configuration (normally, this should already be the case).

3Set the Configuration switch to 2 for configuration:

Configuration switch: 2

The Extender will restart. After start-up, the Power and Ethernet LEDs are green and the Busy LED is red/green blinking.

4Open the browser.

5Type the IP address of the Extender in the address bar of the browser: 192.168.8.80. (This is also printed on the back of the Extender.)

You may have to refresh the browser before the Configuration Tool appears.

13

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model RX9001 User Guide Serial Extender Avertissements RX9001 UserRX9001 UserGuideGuide Contents RX9001X9001 User GuideUser GuideBefore You Start Unpacking the Extender Serial ExtenderInstalling the Extender Mounting the Extender in a RackAdjusting the Power Level of the IR Outputs Connecting the Extender to External EquipmentAttaching the Extender to Infrared Controlled A/V equipment Using the Sensor Inputs Wizz.it ExConnecting to Relay-controlled Equipment Connecting to Serial EquipmentOpen Wizz.it Ex Open the configuration file Connecting to a Lutron RadioRa Lighting SystemOpen the Lutron Lighting System Properties Connecting the Extender to the Network Using the ExtenderSet the Configuration switch to 1 for use Inserting a Multimedia Server in the NetworkConfiguration with a direct connection to the PC Configuring the ExtenderSet the Configuration switch to 2 for configuration Set the Configuration switch to 3 for configuration Configuration through a routerTools menu, select Extender Discovery Troubleshooting SupportWhat Do the LEDs Indicate? There is an IP conflictResetting the Extender Firmware UpdateOperating A/V components with the Extender Updating the Extender through a Router Serial Extender User Guide SpecificationsRemarks RX9001 User Guide RX9001 User Guide FCC Compliancy Czech Likvidace starého výrobkuDanish Bortskaffelse af dit gamle produkt Dutch Verwijdering van uw oude productFinnish Vanhan tuotteen hävittäminen French Mise au rebut des produits en fin de vieGerman Entsorgung Ihres alten Geräts Hungarian Az elhasznált termék hulladékkezeléseIii Marantz America, Inc Corporate Drive Mahwah, NJ07430 Is a registered trademark
Top Page Image Contents