InFocus TD32, TD40 NTSC manual Important Safety Information

Page 8

Important Safety Information

Do not overload the wall outlet or extension cords. Overloading can result in fire or electric shock.

Do not insert anything through the openings in the unit, where they can touch dangerous voltage points or damage parts. Never spill liquid of any kind on the Monitor.

Bend antenna cable between inside and outside building to prevent rain from flowing in.

-This may cause water damaged inside the Monitor and could give an electric shock.

Ground outdoor antennas. If an outside antenna or cable system is connected to the Monitor, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA No.70-1984, provides information about proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

Do not place an outside antenna in the vicinity of overhead power lines or other electric light or power circuits.

- This may cause an electric shock.

There should be enough distance between an outside antenna and power lines to keep the former from touching the latter even when the antenna falls.

- This may cause an electric shock.

Do not attempt to service the Monitor yourself. Refer all servicing to qualified service personnel. Unplug the unit from the wall outlet and refer servicing to qualified service personnel under the following conditions:

when the power-supply cord or plug is damaged

if liquid has been spilled on the unit or if objects have fallen into the unit

if the Monitor has been exposed to rain or water

if the Monitor does not operate normally by following the operating instructions

if the Monitor has been dropped or the cabinet has been damaged

when the Monitor exhibits a distinct change in performance

OWNER'S MANUAL 7

Image 8
Contents USER’S Guide Contents Setting the Picture FCC Notice Page Important Safety Information Follow all operating and use instructionsImportant Safety Information Important Safety Information Only use the specified batteries Accessories Viewing the Control PanelOSD Key Position OSD Key FunctionViewing the Connecting Panel Back Panel and JacksBack panel of the monitor RS-232C To control from PC For PC, Set top boxRS-232C Configurations Connects a control signal from a PCConnects a sound signal from PC or DVI Connects a sound signal from componentViewing the Remote Control Key DescriptionPIP Picture In Picture Keys Move key Move the position of PIP window OFF Small Large TwinReception Range of Remote Control Loading the BatteriesLoad two AAA batteries, taking Care that the + and ends face Correct directionInstallation Table Stand Installation OptionalSpeaker Installation Optional Speaker AccessoriesConnecting the TV Cable Connecting the TV CableConnecting the VCR Connecting the VCRWatching VCR With S-VideoConnecting the DVD Connecting the DVDHow to use Component Input portsConnecting the Set Top Box How to connectWith Component With RGBD-Sub or DVIConnecting the PC D-Sub & DVI Connecting a PC to the MonitorPin Configuration 15Pin Signal Cable based on protruded pinDisplayable Monitor Specification Vertical Frequency HzVolume Control Basic OperationTurning the Monitor On/Off Select SourceOSD Menu Structure Example of OSD MenuMain Menu Sub MenuSetting the Channel Then the tuning bar will appear and scanning will startChannel Type Auto ScanDigest Adjust the fine tune with VOL+ or VOL- buttonFine Tune Set the favorite channel Skip and Fav menu appearAdd the current channel into the scanned channel list Remove the current channel from the scanned channel listSetting the Picture ModeAdjust User Mode Contrast BrightnessColor TintTemperature Cool 1Normal Warm 1Video NR Screen FormatExpands Wide mode screen vertically Screen Format Description WidePanorama ZoomSetting the Picture PC GeometryMismatchMatch Balance Setting the SoundSound Mode User Adjust Spatial EffectAVCAuto Volume Control MTS Multichannel Television SoundSetting the Others TranslucentPIP Picture In Picture Size in PIP Picture In PictureSource in PIP Picture Swap in PIP Picture In PictureAdvanced Position in PIPChange the position of the PIP window Sub Menu, there are four positionsSet ID in Advanced Blue Back in AdvancedLanguage in Advanced Front Key Lock in AdvancedChip TV Parental Guidelines Select TV Blocking with CH+/CH- button on TV Blocking in V-ChipMovie Blocking in V-Chip Enter to Change Password in V-ChipChip Blocking in V-Chip Setting the Time Time SetOn Time On TimeCursor moves into Parts On VolumeOn Channel Off Time SleepTroubleshooting Problem Quick Action for Possible SolutionWarranty Card Limited WarrantyLimited Warranty Period To Be Eligible For Limited Warranty Coverage