InFocus SP8600 manual Declaration of Conformity, Trademarks, FCC Warning, Canada, Agency Approvals

Page 2

Declaration of Conformity

Manufacturer: InFocus Corporation, 13190 SW 68th Parkway, Portland, Oregon 97223-8368 USA

We declare under our sole responsibility that this projector conforms to the following directives and norms:

EMC Directive 2004/108/EC EuP Directive 2005/32/EC EMC: EN 55022

EN 55024 EN 61000-3-2 EN 61000-3-3

Low Voltage Directive 2006/95/EC Safety: IEC 60950-1:2005, MOD

Trademarks

Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc. IBM is a trademark or registered trademark of International Business Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or registered trademarks of Adobe Systems Incorporated. DLP® and the DLP logo are registered trademarks of Texas Instruments and BrilliantColor™ is a trademark of Texas Instruments. InFocus, In Focus, and INFOCUS (stylized) are either registered trademarks or trademarks of InFocus Corporation in the United States and other countries.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interferences, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

--Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by InFocus Corporation may void authority to operate the equipment.

Canada

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Agency Approvals

UL, cUL

Other specific Country Approvals may apply. Please see product certification label. This document applies to regulatory model H8300.

Input ratings: AC 100-240V, 4.3-1.6A,50-60Hz

InFocus reserves the right to alter product offerings and specifications at any time without notice.

1

Image 2
Contents Page FCC Warning Declaration of ConformityTrademarks CanadaTable of Contents Important Operating Considerations for Safety When the power cord or plug is damaged or frayed Introduction Optional AccessoriesProduct specifications Online registrationConnector panel 12V External Trigger outputsPositioning the projector Horizontal Offset +/-15%Ceiling Mount Range of distance to the screen for a given screen sizeCable management HDMI 1.3 connection Connecting powerConnecting a computer source VGA connectionDisplaying an image No start up screen? Get help on pageAdjusting the image Composite video connection Connecting a video deviceVideo device connections S-video connectionWhat is Aspect Ratio? Shutting down the projector Troubleshooting your setupTable 1 Status indicator light behavior and meaning Screen Save TimePlug power cord into the projector, then press Problem No start up screen Only start up screen appearsSolution power buttonrange” ProblemNo computer image, just the words “Signal out of Only my laptop’s background appears, not thePanel Display Settings tab Set your computer’s display resolution to the nativeresolution of the projector Start Settings Control Move projector, adjust zoom and lens shiftImage not square Adjust Keystone in the Basic Picture menuAdjust Sharpness in the Basic Picture menu Square imageAdjust color, tint, brightness, contrast in the Basic Turn off Ceiling Mount in Setup menuTurn off Rear Project in Setup menu Image upside downEmbedded video plays correctly The video embedded in my PowerPointTurn off the internal LCD display on your laptop presentation does not play on the screenwon’t turn on, Lamp light is turned on “Replace lamp” message appears at startup, lampLamp must be replaced see page Replace lamp Lamp doorUsing the remote control Troubleshooting the remoteOptimizing computer images Using the keypad buttonsPresentation features Optimizing video images Customizing the projectorUsing the menus Basic Picture menu Advanced Picture menu Setup menu Menu Transparency Allows you to change how much of the projected image Status and Service menu HelpWARNINGS MaintenanceCleaning the lens unplug projector Replacing the projection lampTurn off and Using the security lock HDMI AppendixSplitScreen Compatibility RS-232 Port Settings RS-232 CommandsCommunication Configuration Command FormatLimitations Write Command ExamplesError Conditions Signal 1 TimerResolution Blank Screen Style1 Lamp won’t strike Lamp Total On Time Projector Info menu 1 DisplaySave User Presets Reset Lamp Hours1 Reset CommandSystem State INDEX Numerics