InFocus LP810 manual Turning on / OFF Projector, Turning on Projector, Turning OFF Projector

Page 19

BEFORE OPERATION

TURNING ON / OFF PROJECTOR

TURNING ON PROJECTOR

1

Complete peripheral connections (with Computer, VCR, etc.)

before turning on projector. (Refer to "CONNECTING TO

 

PROJECTOR" on pages 11~13 for connecting that equipment.)

2

Connect a projector's AC Power Cord into an AC outlet. LAMP

Indicator lights RED, and READY Indicator lights GREEN.

 

NOTE : When “On start” function is ON, this projector is turned

 

on automatically by connecting AC Power Cord to an

 

AC outlet. (Refer to pages 35, 36.)

3

Press POWER ON-OFF button on Top Control or on Remote

Control Unit to ON. LAMP Indicator dims, and Cooling Fans

start to operate. Preparation Display appears on a screen and count-down starts. Signal from PC or Video source appears after 30 seconds.

Current Input position and Lamp mode status are also displayed on screen for 5 seconds. (Refer to "LAMP MODE" on page 36.)

Input position and

Lamp mode status

Input 1

30

E

Preparation Display disappears after 30 seconds.

TURNING OFF PROJECTOR

1

Press POWER ON-OFF button on Top Control or on Remote

Control Unit, and a message "Power off?" appears on a screen.

2

Press POWER ON-OFF button again to turn off projector. LAMP

Indicator lights bright and READY Indicator turns off. After

 

projector is turned off, Cooling Fans operate (for 90 seconds).

 

During this "Cooling Down" period, this appliance cannot be

 

turned on.

3

When projector has cooled down, READY Indicator lights

GREEN again and you can turn projector on. After cooling down

completely, disconnect AC Power Cord.

TO MAINTAIN LIFE OF LAMP, ONCE YOU TURN PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE TURNING IT OFF.

Power off?

Message disappears after 4 seconds.

When “Power Management” function is ON, projector detects signal interruption and turns off Projection Lamp automatically. Refer to “Power Management” on page 35.

When WARNING TEMP. Indicator flashes red, projector is automatically turned off. Wait at least 5 minutes before turning on projector again.

When WARNING TEMP. Indicator continues to flash, follow procedures below:

1.Press POWER ON-OFF button to turn a projector off and disconnect AC Power Cord from an AC outlet.

2.Check Air Filters for dust accumulation.

3.Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 38.)

4.Turn a projector on again.

If WARNING TEMP. Indicator should still continue to flash, contact sales dealer where you purchased this projector or service center.

19

Image 19
Contents LP810 To the Owner Voor de klanten in Nederland Safety InstructionsFederal Communication Commission Notice CompliancesTable of Contents Component Video Features and DesignComputers Color SystemsName of Each Part of Projector Preparation200 240 V AC SETTING-UP ProjectorConnecting AC Power Cord For U.S.A. and Canada For Continental EuropeRoom Light Preparation Positioning ProjectorMoving Projector Preparation Adjustable FeetBNC Input Jacks Connecting ProjectorUSB Connector Series B Terminals of ProjectorTerminals A Projector Connecting to ComputerConnecting to Video Equipment Before Operation Operation of Remote ControlLaser Pointer Function Focus Button Volume ButtonWired Remote Jack Zoom ButtonPoint Volume + / Buttons TOP Controls and IndicatorsOperating ON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Guide Window Before Operation Menu BARSound Menu Turning on Projector Turning on / OFF ProjectorTurning OFF Projector Keystone Adjustment Adjusting ScreenBasic Operation Sound Adjustment Input Menu Computer InputSelecting Input Source Selecting Computer SystemAuto PC AdjustmentAuto PC Adjustment Computer Input Automatic MULTI-SCAN SystemComputer Input Manual PC Adjustment Full screen Computer InputDisplay area Display area H1024 x 48.363 60.004 Computer Input Compatible Computer SpecificationsResolution 640 x 31.469 59.940Image 1~4 Picture Image AdjustmentsImage Level Select Direct Image Level Select MenuImage Adjust Menu Computer Input Image Level AdjustmentScreen Menu Picture Screen AdjustmentSource Select Menu Video Video InputVideo Pb/Cb,Pr/CrPAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-N Component Video Signal FormatSelecting Video System Video InputImage button Standard Cinema CinemaVideo Input Image Level Adjustment Closes Image Menu Reset Reset all adjustment to previous figure QuitSetting Menu SettingSetting Menu To change code of Projector To change code of Remote Control UnitWireless Mouse mode Projector modeOperating Wireless Mouse SETTING/APPENDIXOperating Wireless Mouse InstallationAIR Filter Care and Cleaning MaintenanceCleaning Projection Lens Lamp Replace Counter Appendix Lamp ReplacementTroubleshooting Function does not Remote Control UnitWireless Mouse Does not workTechnical Specifications USB Connector Series B Appendix Configurations of TerminalsWarranty Limitation and Exclusion Limitation of Liability 11/2002 610 304 0035 1AA6P1P3748-- PK3F

LP810 specifications

The InFocus LP810 is a high-performance projector designed to meet the demands of professional presentations, educational settings, and corporate use. Renowned for its exceptional image quality and advanced features, the LP810 makes it an ideal choice for those who value clarity and detail in visual presentations.

One of the standout features of the InFocus LP810 is its impressive brightness, rated at 3500 ANSI lumens. This ensures that it performs well in various lighting conditions, providing vivid and bright images that capture the audience's attention, even in well-lit rooms. Coupled with a high contrast ratio of 2000:1, the projector delivers deep blacks and vibrant colors, making it perfect for displaying everything from detailed presentations to dynamic videos.

The LP810 employs DLP technology, which is known for its reliability and longevity. DLP projectors are less susceptible to color decay, ensuring that the images remain consistent over time. The InFocus LP810 also features a native XGA resolution of 1024 x 768 pixels, allowing for sharp image quality that enhances the clarity of text and graphics. Moreover, it supports various resolutions up to 1080p, making it versatile for different content formats.

Connectivity is a vital aspect of any projectors, and the InFocus LP810 does not disappoint. It offers multiple input options, including HDMI, VGA, and composite, accommodating various devices such as laptops, Blu-ray players, and gaming consoles. Additionally, the projector supports an RS-232 port for advanced integration into control systems, making it suitable for installation in larger venues.

Portability is another characteristic of the LP810, with a compact design that weighs approximately 5.5 pounds. This lightweight design facilitates easy transportation, making it a great choice for professionals who need to present in different locations. The projector also includes onboard controls, allowing users to make quick adjustments without needing a remote.

In terms of usability, the LP810 features an intuitive menu system that simplifies navigation, alongside an automatic keystone correction that ensures the image remains properly aligned, regardless of the projector's positioning. The inclusion of an Eco mode extends the life of the lamp while also reducing energy consumption, which is an added benefit for environmentally conscious users.

In summary, the InFocus LP810 is a versatile and powerful projector that combines advanced technology with user-friendly features. Its high brightness, exceptional image quality, and extensive connectivity options make it an excellent choice for any professional or educational setting. Whether you're delivering a crucial business presentation or engaging a classroom full of students, the LP810 ensures that your visuals stand out.