Marantz PD5001 manual Wide Operations, When viewing videos or digital video discs

Page 15

WIDE Operations

Wide Screen Operation (manual)

With this function, you can select one of seven screen sizes.

When viewing videos or digital video discs

1.Press the WIDE button on the remote control.

2.Within 3 seconds ...

Press the WIDE button again.

The screen size switches as follows:

→ NORMAL → ANAMORPHIC → STADIUM → ZOOM → 2.35:1 → 14:9 → UNDERSCAN

When a 720P or 1080I signal is input:

ANAMORPHIC ↔ 2.35:1

When displaying enhanced split screen:

NORMAL ↔ ANAMORPHIC

NORMAL size screen (4:3)

The normal size screen is displayed.

*The picture has the same size as video pictures with a 4 : 3 aspect ratio.

ANAMORPHIC size screen

The image is expanded in the horizontal direction.

*Images compressed in the horizontal direction (“squeezed images”) are expanded in the horizontal direction and displayed on the entire screen with correct linearity. (Normal images are expanded in the horizontal direction.)

STADIUM size screen

The picture is expanded in the horizontal and vertical directions at different ratios.

*Use this for watching normal video programs (4:3) with a wide screen.

ZOOM size screen

The picture is expanded in the horizontal and vertical direction, maintaining the original proportions.

* Use this for theater size (wide) movies, etc.

2.35:1 size screen



Original image Information is lost on both sides.

The squeezed film image is expanded to fulfill the entire screen at a ratio of 2.35:1. Black bands do not appear at the top and bottom but information is lost on the left and right margins.

•This feature is available when the input signal is video, component (480I, 480P, 576I, 576P, 720P, 1080I) or RGB

(525P or 625P signal from a scan converter).

*If black bands appear on the top and bottom in the full size screen, select the 2.35:1 size screen to fill the screen and avoid image retention.

14:9 size screen

The image is displayed at a 14:9 aspect ratio.

*This feature is available when the input signal is video, component (480I, 480P, 576I, 576P) or RGB (525P or 625P signal from a scan converter).

UNDERSCAN size screen

Set “UNDERSCAN” to “ON” in the “IMAGE ADJUST”. Typical televisions crop the image (i.e., overscan). In order to restore the entire image, select UNDERSCAN.

Overscan

Underscan

*Picture noise or black border may appear near the edge of screen depending on the connected component.

*The continuous display in this screen size over a prolonged period of time may result in image retention.

*When Macrovision signal is input, the brightness may change.

Note:

Do not allow 4:3 content to be displayed for extended periods of time without using gray bars. This can cause image retention.

16

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model PD5001 User Guide Additional Safety Information Important Safety InstructionsInformations de Sécurité Supplémentaires AvertissmentImportant Information PrecautionsRecommandations importantes PrécautionAvertissements et précautions de sécurité Operating Environment PD5001 Remarque AvertissementContents Ventilation Requirements for enclosure mounting InstallationOperating Range Using the remote controlBattery Installation and Replacement Cable ManagementFront View Turns the monitor’s power on and offReceives the signals from the remote control Part Names and FunctionPD5001 Rear View/ Terminal BoardRemote Control Basic Operations Wide Operations When viewing videos or digital video discsNormal size screen 43 or Sxga Wide Screen Operation with Computer SignalsWhen wide signals are input  Supported resolutionOperations in the Side-by-side mode Split Screen OperationsShowing a couple of pictures on the screen at the same time Zooming in on a specific input Operations in the Picture-in-picture modeSelecting the input signals to be displayed Adjusting the OSM controlsMenu Operations  Advanced menu modeMain menu Sub menu Sub menu 3 Sub menu Menu TreeReset  Restoring the factory default settingsReducing noise in the picture Picture Settings MenuStoring picture settings Adjusting the picture Adjusting the white balance Setting the color temperatureAdjusting the color to the desired level Setting the picture to suit the movieChanging the Gamma Curve Making the Low Tone adjustmentsAdjusting the pedestal level black level Adjusting the colorsAudio Settings Menu Image Adjust Settings MenuSetting the allocation of the audio and DVD/ HD connectors SET UP Settings Menu Setting the black level for Hdmi signal Setting the video signal formatSetting the background color when no signal is being input Setting the position of the menu Etting the screen size for S1/S2 video inputTurning on/off the menu display Setting the power management for computer images Function Settings MenuResetting to the default values Setting the menu modeDisplaying still images in the sub screen ON/STANDBY indicatorSetting the Input Skip Displaying the entire image during Digital Zoom operationsReducing image retention  When set to Auto Peak Bright settings  Orbiter settings OSM Orbiter settings Setting Closed Caption INVERSE/WHITE Settings  Soft Focus settingsSignal Information Menu Setting the power on modeReducing the brightness of Closed Caption Pin Assignments External Control1/8 Stereo Mini cable must be purchased separately Connection Example Connecting an STBConnection with STB Connection ExampleSymptom Checks Remedy TroubleshootingSpecifications PD5001 Computer input signals supported by this system Supported resolution PD5001KHz 169 CVT standard compliantIs a registered trademark
Top Page Image Contents