Marantz PD4240D manual Important Information, Precautions, Risk of Electric Shock Do not Open

Page 3

Important Information

Precautions

Please read this manual carefully before using your plasma monitor and keep the manual handy for future reference.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside of this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS UNIT’S POLARIZED PLUG WITHAN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS, UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Warnings and Safety Precaution

This plasma monitor is designed and manufactured to provide long, trouble-free service. No maintenance other than cleaning is required.

Please see the section “Plasma monitor cleaning procedure” on the next page.

The plasma display panel consists of fine picture elements (cells) with more than 99.99 percent active cells. There may be some cells that do not produce light or remain lit.

For operating safety and to avoid damage to the unit, read carefully and observe the following instructions. To avoid shock and fire hazards:

1.Provide adequate space for ventilation to avoid internal heat build-up. Do not cover rear vents or install the unit in a closed cabinet or shelves.

If you install the unit in an enclosure, make sure there is adequate space at the top of the unit to allow hot air to rise and escape. If the monitor becomes too hot, the overheat protector will be activated and the monitor will be turned off. If this happens, turn off the power to the monitor and unplug the power cord. If the room where the monitor is installed is particularly hot, move the monitor to a cooler location, and wait for 60 minutes to cool the monitor. If the problem persists, contact your Marantz dealer for service.

2.Do not use this unit’s polarized plug with extension cords or outlets unless the prongs can be completely inserted.

3.Do not expose the unit to water or moisture.

4.Avoid damage to the power cord, and do not attempt to modify the power cord.

5.Unplug the power cord during electrical storms or if the unit will not be used over a long period.

6.Do not open the cabinet which has potentially dangerous high voltage components inside. If the unit is damaged in this way the warranty will be void. Moreover, there is a serious risk of electric shock.

7.Do not attempt to service or repair the unit. The manufacturer is not liable for any bodily harm or damage caused if unqualified persons attempt service or open the back cover. Refer all service to authorized Marantz Service Centers.

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Model PD4240D User Guide Introduction to the Plasma Monitor Features you’ll enjoy includeContents of the Package IntroductionPrecautions Important InformationRisk of Electric Shock Do not Open Plasma monitor cleaning procedure To avoid damage and prolong operating lifeRecommendations to avoid or minimize phosphor burn-in Risque D’ELECTROCUTION Recommandations importantesPrécautions Mises en garde et précautions de sécuritéMéthode de nettoyage du moniteur à plasma Contents Ventilation Requirements for enclosure mounting How to Attach Options to the Plasma MonitorFront View Turns the monitor’s power on and offReceives the signals from the remote control Part Names and FunctionConnect DVD’s, High Definition or Laser Discs, etc. here Connect the included power cord hereSyncronization signal Rear View/ Terminal BoardRemote Control Clears the number set by the ID Select button Battery Installation and ReplacementTransmits the remote control signals Not functional for the models covered in this manualApprox 7m/23ft Using the wired remote control modeHandling the remote control Operating RangeInstallation Digital signal outputPersonal computer with a Connections with Equipment that have a Digital Interface Connecting Your Document CameraConnecting Your VCR or Laser Disc Player Connecting Your DVD PlayerPin No Signal Analog Pin Assignments and Signal Levels for 15 pin RGB AnalogCable Management Creating a video wallBasic Operations To check the remaining time To set the off timerTo cancel the off timer After the power is turned off with the off timerWide Operations When viewing videos or digital video discs Picture Size setting Wide Screen Operation with Computer SignalsWhen Picture Size is set to OFF  Supported resolutionMenu Operations  Advanced menu modeMenu Tree ResetOnly when Auto Picture is OFF RGB/PC only Adjusting the picture Picture Settings MenuSetting the color temperature Adjusting the color to the desired levelReducing noise in the picture  LOW Tone settings Making the Low Tone adjustments Adjusting the white balance  Gamma settings Audio settings menu Audio Settings MenuAdjusting the colors  Color Tune settingsExample Setting Audio INPUT1 to Video Image Adjust Settings MenuSetting the allocation of the audio connectors Adjusting the Position, Size, Fine Picture, Picture AdjSetting the on-screen menu Option1 Settings Menu OSM Orbiter settings Setting the BNC connectorsChecking the signal being transmitted to RGB1 terminal Setting a computer image to the correct RGB select screen RGB Select modes Setting high definition images to the suitable screen sizeSetting the Input Skip  Input Skip settingsOption2 Settings Menu Resetting to the default valuesSetting the power management for computer images Reducing burn-in of the screen POWER/STANDBY indicatorSetting the picture to suit the movie PLE settingsOrbiter settings Orbiter Function settingsInverse Settings Setting the time To select on for the Working TimeScreen Wiper Gray Level settings Setting the screen size for S1/S2 video inputSoft Focus settings Setting the gray level for the sides of the screenPLUG/PLAY settings Setting the picture size for RGB input signalsSetting the signal and black level for DVI signal S1/S2 settingsPresent Time Option3 Settings MenuUsing the timer Present Time settingsSpecial characters in the Program Timer screen Setting the power on modeTo reset the program To reset the dataIR Remote settings Enabling/disabling remote control wireless transmissionPWR. on Mode settings Control Lock settingsID number setting Loop Out settingScreens Video Wall settingDivider settings Video Wall Position settingsAuto ID settings DISP. Mode settingsImage Adjust settings PLE Link On Delay Power on delayOn Delay settings PLE Link settingsRepeat Timer settings Advanced OSM Settings MenuSetting the menu mode Repeat TimerSetting the video signal format Language Settings MenuColor System Settings Menu Setting the language for the menusCommunication Parameters External ControlApplication ConnectionsSymptom Checks Remedy TroubleshootingPage Page Model PD4240D Information Important Safety Instructions PD4240D Précautions Importantes DE Sécurité PD4240D DVI cable not supplied Band Avertissement DOC avis de conformationRemarque Specifications RGBDVD/HD/DTV Full DVI Table of Signals SupportedSupported resolution Computer input signals supported by this systemDeclaration of Conformity Japan Is a registered trademark
Top Page Image Contents