JVC DLA-HX2E, DLA-HX2U Adjusting the Sound Volume, Power Off, Press Volume · 50, Turn off Blink

Page 27

Basic Operations

5. Adjusting the Sound Volume

To increase the volume : press [VOLUME] ª (0 50)

 

 To lower the volume

: press [VOLUME] · (50 0)

VOL.

VOLUME

 

STAND BY

LAMP TEMP OPERATE

PC VIDEO

V-KEYSTONE H-KEYSTONE

VOL.

MENUEXIT

ENTER

6-1

5

Projector:

Remote

Control panel

control unit

Audio-Vol

12

When “Menu display” (page 39) is set to “15sec”, after pressing the [VOLUME] button, the sound vol- ume display will appear on the screen for about 15 seconds.

(Press [EXIT] button to immedi- ately remove the “Audio-Vol” dis- play.)

Audio-Vol 12

OPERATE

PC VIDEO

W

V-KEYSTONE H-KEYSTONE SCREEN DIGITAL ZOOM

 

S

 

FREEZE

VOLUME FOCUS

QUICK ALIGN.

MENU

EXIT

ENTER

 

6-1

5

Screen display

Note

When the sound volume is displayed on the screen, pressing the [PRESET] button will reset the set value to “0”.

6.Power Off

1 Press the [OPERATE] button on the projector (or the [OP-

ERATE] button on the remote control unit ) for 1 second or more

The [OPERATE] indicator will disappear, the [STAND BY] in- dicator starts to blink, and the projector goes into the cool- down mode. The [STAND BY] indicator will continue blinking for approximately 90 seconds as the temperature of the light source lamp cools (Cool Down Mode).

PRESET

HIDE

OPERATE

OPERATE

Projector:

Remote

Control panel

control unit

Turn off Blink

STAND BY

LAMP TEMP OPERATE

Projector: Indicator

Note

The [OPERATE] button will not work for approximately 1 minute from when the light-source lamp is turned on. Wait approxi- mately 1 minute before pressing.

2Plug out the power cord from wall outlet

Caution

Please do not pull out the plug from the power source when the [STAND BY] indicator is blinking. It will shorten the life of the lamp and cause a malfunction.

27

Image 27
Contents Model No. DLA-HX2U Serial No For customer UseMachine Noise Information Germany only FCC Information U.S.A. onlyFor United For European Kingdom Safety PrecautionDo not allow any unqualified person to install the unit Power supply voltage AC 120Do not cut off the main plug from this equipment How To Replace The FuseAbout burning-in of the D-ILA device Using the projectorHow to use the Screen Trigger terminal cable Using the screen mode switch functionAccessories ContentsFront Side/ Top Surface/ Left Side Controls and FeaturesRear Side/ Right Side/ Bottom Surface Controls and FeaturesConnector Panel Control Panel on the Projector Indicator Display on the Control PanelTemp Indicator Stand by IndicatorOperate Indicator Lamp IndicatorFocus button Not functional on this unit Remote Control UnitVolume button Video button PC buttonDigital Zoom ª / · buttons Remote Control’s signal transmitter Operate buttonVolume ª / · button Screen „ / Í buttonLoad the batteries Loading Batteries into the Remote ControlPrecautions for using batteries Open the back coverPrecautions for Installation Installing the ProjectorMounting the Projector Installing the Projector against the ScreenInstalling the Projector Precaution for ceiling-mount Screen installation Projection Distance and Screen Size43 Screen When the remote control unit fails to work properly Effective Range and Distance of the Remote Control Unit Using as a wireless remote control unit  Using as a wired Remote Control Computer signals Connecting to Various DevicesSignals that can be input into the Projector  Video signals Allowable input signals Connecting to Various DevicesConnection Connecting to Devices Connecting to Video Devices Right side of projector Connecting to Computers RS-232C connection cable sold separately Cross cable  Control from external deviceCross cable Connection for controlling more than one projector When using the projector, remove the Lens Cap Connecting the Power Cord suppliedBasic Operations Basic Operation ProceduresPower On Insert the power cord into the wall outletBasic Operations  Display using the direct buttonsAdjusting the Zoom Ring the screen size Adjusting the Focus Ring FocusPlug out the power cord from wall outlet Adjusting the Sound VolumePower Off Press Volume · 50Enlarging the Image Frequently used Convenient FunctionsDisplaying a Still Picture Turning Off Image and SoundRemoving the Trapezoidal Distortion of the Image  Vert.keystone Display Horiz.Keystone Display Using the Quick Alignment function Press the Quick ALIGN. Quick Alignment buttonQuick Alignment function Submenu Adjustments and Settings Using MenusMenu Structure Main menuMain menu Submenu Adjustments and Settings Using MenusMain Set up menu When PC input is selected Main Set up menu When video input is selectedMenu Operation Buttons MenuButton Procedure for Menu Operation Image adj. menu Adjustment and Setting Using MenusMenu Configuration Set up menuResize menu Position menuAspect ratio menu Decoder menuLanguage menu Capture startOptions menu Color profile menuInformation menu Setting Aspect ratio and Resize Setting the Aspect ratioProject the image onto the screen Optimum image Setting Aspect ratio and ResizePress the Menu button to end when adjustment is com- pleted Select Zoom with the cursor buttons  / Resize menu appears on the screen Setting the ResizeSet the Resize when Hdcp image is input from PC3 terminal Select Resize with the cursor buttons  /  and press EnterSet Resize to Zoom for optimum projected image Press the Enter or the right cursor button  Editing and Projecting LogoProject the images to be included in your logo Select Logo with the cursor buttons  / Editing and projecting logo Light source lamp and its lamp time Procedure for lamp replacementAbout lamp replacement Replacing the LampClose the handle, and tighten the screw Replacing the LampRemove the lamp unit Insert the new lamp unit until it is fullyPress for Resetting the lamp timeInsert the power cord into the wall outlet To ensure the lamp time has been resetReinstalling the filter Cleaning and Replacing the FilterPull out the power cord from the wall outlet Clean the filterPlied TroubleshootingSymptom Probable cause Corrective action TroubleshootingMessage Cause Contents What to do when these messages are displayedWhat to do when these messages are displayed  Action to be taken upon warning indications  About warning indicatorsIndicator Please follow the procedures belowPB, PR Specifications Bottom SpecificationsDimensions unit mm  Top  Front PC 3 terminal Pin number Signal namePin arrangement  Y/C terminal  RS-232C IN/OUT terminal  PC 1 terminalCommunication Specifications Command Format RS-232C external control External control command table Memo SW-VP