Connector Panel

JVC DLA-HX2E, DLA-HX2U manual Connector Panel

Controls and Features

1 [PC2] Input Terminal

2 [PC1] Input Terminal

3 [PC3] Input Terminal

R PR/CR

G Y

B PB/CB H/CS

PC2

DVI

PC3

PC1

SCREEN	REMOTE	RS-232C OUT	RS-232C IN	Y/C	VIDEO
TRIGGER AUDIO IN		CONTROL		VIDEO IN

4 [SCREEN
4 [SCREEN	6 [REMOTE]		8 [Y/C] Input
TRIGGER]	Terminal		Terminal
Terminal
Terminal
5 [AUDIO IN]		7 [CONTROL RS232C		9 [VIDEO] Input
	Terminal	IN/OUT] Terminal		Terminal

1[PC2] Input terminal (BNC x 5)

This is an input terminal for component signals (Y, CB, CR) or DTV-format (Y, PB, PR) signals. Devices which have com- ponent signal output terminals can be connected. This ter- minal can also be used as multipurpose video input termi- nals that allow input of the following signals: analog RGB signals, vertical sync (V) signals, and horizontal sync (H) signals/ composite signals (Cs). Devices which have ana- log RGB signals output terminals can be connected.

(☞ page 21, 22)

To use this terminal, the “PC2(BNC)” item in the “Options” menu must be set correctly according to the input signals. (☞ page 39)

•Input of external sync signals is automatically detected. Detection of H/V signals or Cs signals causes automatic switching to external sync. The priority order is H/V>Cs.

•When computer signals are input, the uppermost edge of the image may appear to bow if the sync signal input is a composite sync (Cs) or G on sync signal. In this case, please use separate sync signals for vertical sync (V) and horizontal sync (H).

•Input signals of 720p (50Hz) are not supported.

2[PC1] Input terminal (D-sub 3 rows 15 pin)

This is an input terminal dedicated to computer signals (RGB Video signals and sync signals).

Connect the display output terminal of the computer to this terminal. When a Macintosh computer is to be connected, please use the conversion adapter (sold separately) for Mac. (☞ page 22)

3[PC3] Input terminal (DVI-D 24 Pin Single)

HDCP compatible video signals (480p, 576p, 720p 50/59/ 60 Hz, 1080i 50/59/60 Hz) and input terminal for personal computer (PC) signal. Connect the display output terminal of the computer to this terminal. (☞ page 22)

•The menu screen for HDCP compatible signal input is the same as when PC input is selected.

4[SCREEN TRIGGER] Terminal

The signal output for controlling roll-up screen that sup- ports [SCREEN TRIGGER]. Outputs DC 12 V / max. 100 mA when power is on.

(Tip = DC +12 V, Sleeve = Gnd)

Before using the supplied cable, read ‘How to use the [SCREEN TRIGGER] terminal cable’ on page 5.

5[AUDIO IN] (audio) Terminal (mini jack)

This is the audio input terminal for devices connected to [PC1], [PC2], [PC3], [VIDEO] or [Y/C]. Connect the audio output terminal of the device to this terminal.

(☞ page 21, 22)

•When [PC1], [PC2], [PC3], [VIDEO] or [Y/C] input is be- ing selected, the inputted audio signals will be reproduced by the projector speaker.

(Audio output for this projector is monaural.)

6[REMOTE] Terminal (stereo mini jack)

When the remote control is unable to work due to rear pro- jection etc., the [REMOTE] terminal can be used to connect an external sensor to the projector. The external sensor is not generally sold. Please check with your authorized dealer.

7[CONTROL RS232C IN/OUT] Terminal (D-sub 9 Pin)

This is the RS-232C interface-specific terminal. The pro- jector can be controlled by a computer connected exter- nally. More than one projector can be controlled using both the [RS-232C IN] and [RS-232C OUT] terminals.

(☞ page 23)

• For details, please check with your dealer.

8[Y/C] Input Terminal (Mini DIN 4 Pin)

This is the input terminal for Y/C (S-Video) signals. Con- nect this terminal to the S-video output terminal of a video deck, etc. (☞ page 21)

9[VIDEO] Input Terminal (RCA pin jack)

This is an input terminal for composite video signals. Con- nect this terminal to the composite video output terminal of a VCR, etc. (☞ page 21)