JVC DT-V17L2D manual Available signals, Attaching the power cord holder, Video signals

7Available signals

The following signals are available for this monitor.

Video signals

		Signal format		Input terminal
No.	Signal name	shown in the		COMPONENT	E. AUDIO HD/	DVI-D (HDCP)
		status display	VIDEO	(Analog	SD SDI	(Digital component/
		(☞ page 7)		component)	(IN 1, IN 2)*1	digital RGB)
1	NTSC	NTSC	√	—	—	—
2	PAL	PAL	√	—	—	—
3	B/W50	B/W50	√	—	—	—
4	B/W60	B/W60	√	—	—	—
5	480/59.94i	480/60i	—	√	√	—
6	576/50i	576/50i	—	√	√	—
7	480/59.94p	480/60p	—	√	—	√
8	576/50p	576/50p	—	√	—	√
9	640∗480/59.94p	640∗480/60p	—	—	—	√
10	720/60p	720/60p	—	√	√	√
11	720/59.94p	720/60p	—	√	√	√
12	720/50p	720/50p	—	√	√	√
13	720/30p	720/30p	—	√	√	—
14	720/29.97p	720/30p	—	√	√	—
15	720/25p	720/25p	—	√	√	—
16	720/24p	720/24p	—	√	√	—
17	720/23.98p	720/24p	—	√	√	—
18	1080/60i	1080/60i	—	√	√	√
19	1080/59.94i	1080/60i	—	√	√	√
20	1035/60i	1035/60i	—	√*2	√	√*2
21	1035/59.94i	1035/60i	—	√*3	√	√*3
22	1080/50i	1080/50i	—	√	√	√
23	1080/60p	1080/60p	—	—	—	√
24	1080/59.94p	1080/60p	—	—	—	√
25	1080/50p	1080/50p	—	—	—	√
26	1080/30p	1080/30p	—	√	√	√
27	1080/29.97p	1080/30p	—	√	√	√
28	1080/25p	1080/25p	—	√	√	√
29	1080/24p	1080/24p	—	√	√	√
30	1080/23.98p	1080/24p	—	√	√	√
31	1080/30psF	1080/60i	—	√*2	√*2	—
32	1080/25psF	1080/50i	—	√*4	√*4	—

Computer signals (preset)

DVI-D (HDCP) terminals

No.	Signal name	Resolution		Frequency		Scan system
		Horizontal	Vertical	Horizontal (kHz)	Vertical (Hz)
1	VGA60	640	480	31.5	59.9	Non-interlace
2	WVGA60	852	480	31.5	59.9	Non-interlace
3	SVGA60	800	600	37.9	60.3	Non-interlace
4	XGA60	1024	768	48.4	60.0	Non-interlace
5	WXGA (1280)	1280	768	47.8	60.0	Non-interlace
6	WXGA+60	1440	900	55.9	60.0	Non-interlace
7	SXGA60*5	1280	1024	64.0	60.0	Non-interlace
8	UXGA60*5	1600	1200	75.0	60.0	Non-interlace
9	WUXGA60*5	1920	1200	74.0	60.0	Non-interlace
10	720/60p	1280	720	45.0	59.9/60.0	Non-interlace
11	1080/60p*5	1920	1080	67.5/67.4	59.9/60.0	Non-interlace

*5 When signals of No. 7 – 9 and 11 come in, thin lines will become obscured because their signal resolution is higher than the screen resolution (1440 x 900).

•Non-preset signals may not be displayed normally even if its frequency is within the acceptable range (☞ “Horizontal/vertical frequency (computer signal)” on page 17).

•When a preset signal comes in, the signal format is shown on the status display. For other signals, the resolution is shown.

Specification of the DVI-D (HDCP) terminal

Connect it to the DVI-D output terminal on a personal computer.

Pin No.	Input signal	Pin No.	Input signal	Pin No.	Input signal
1	T.M.D.S Data 2–	9	T.M.D.S Data 1–	17	T.M.D.S Data 0–
2	T.M.D.S Data 2+	10	T.M.D.S Data 1+	18	T.M.D.S Data 0+
3	T.M.D.S Data 2 shield	11	T.M.D.S Data 1 shield	19	T.M.D.S Data 0 shield
4	NC	12	NC	20	NC
5	NC	13	NC	21	NC
6	DDC Clock	14	+5 V Power	22	T.M.D.S Clock shield
7	DDC Data	15	GND	23	T.M.D.S Clock+
8	NC	16	Hot Plug Detect	24	T.M.D.S Clock–

Note for connections

•Before making any connections, turn off all the equipment.

•Use a cord whose plugs correctly match the terminals on this monitor and the equipment.

•Plugs should be firmly inserted; poor connections could cause noise.

•When unplugging a cord, be sure to grasp its plug and pull it out.

•DO NOT connect the power cord until all connections are completed.

•Refer also to the user manual of each piece of equipment.

33	1080/29.97psF	1080/60i	—	√*3	√*3	—
34	1080/24psF	1080/24psf	—	√	√	—
35	1080/23.98psF	1080/24psf	—	√	√	—

√: Acceptable

—: Not acceptable

*1 Compatible with EMBEDDED AUDIO signals *2 The signal is recognized as 1080/60i.

*3 The signal is recognized as 1080/59.94i. *4 The signal is recognized as 1080/50i.

Attaching the power cord holder

•The provided power cord holder prevents accidental disconnection of the AC power cord from the AC IN terminal.

•The power cord holder consists of two parts, a case and a cover.

12 Cover 3

Case AC IN terminal

CAUTION

•Use only the provided screws.

•Make sure the plug will not be pulled out after the cover is attached to the case.

•To detach the cover, release the tab.

• Analog component signals are compatible with Y on sync signals.

Tab

ENGLISH9