Daily Operations / Connections (cont.)
8
7Rear panel
Carry handle
Use this handle when carrying the monitor.
CAUTION
Do not connect the power cord until all other connections are completed.
Security slot
Install a security wire to this slot.
1REMOTE terminal
Terminal for controlling the monitor by an external control. ☞ “External Control” on page 14
2VIDEO terminals (BNC)
Input (IN) and output (OUT) terminals for the composite signals.
3COMPO. (Y,
4AUDIO (IN) terminals (pin jack)
Input terminals for the analog audio signals.
•Use this terminal for the analog audio connection of the SDI.
5AUDIO (MONITOR OUT) terminals (pin jack) Output terminals for the analog audio signals.
•The terminals emit the audio signals through the AUDIO (IN) terminal or EMBEDDED AUDIO signals through the E. AUDIO HD/SD SDI input terminal.
•The signals are emitted from these terminals only when the monitor is on or in P.SAVE (power save) mode.
•The EMBEDDED AUDIO signals are decoded into an analog signals, then emitted.
•The EMBEDDED AUDIO signals are emitted only when “SDI 1” or “SDI 2” is selected, and when EMBEDDED AUDIO signals come in to the E. AUDIO HD/SD SDI input terminal.
6E. AUDIO HD/SD SDI (IN 1, IN 2) terminals (BNC) Input terminals for the HD/SD SDI signals.
•The terminals accept also EMBEDDED AUDIO signals including up to 12 audio channels with the sampling frequency of 48 kHz.
7E. AUDIO HD/SD SDI (SWITCHED OUT) terminal (BNC)
Output terminal for the HD/SD SDI signals.
•The SDI signals of the current input (SDI 1 or SDI 2) are
•When the input other than SDI 1 and SDI 2 is selected, the SDI signal of the input selected last time is emitted from this terminal.
•The signals are emitted from this terminal only when the monitor is on or in P.SAVE (power save) mode.
8DVI-D (HDCP) terminal
Input terminal for the
•When the picture is not displayed correctly, change the setting of “DVI INPUT SEL.” (☞ page 10).
•The
9DC IN 12V terminal
DC 12 V (maximum DC 17 V) power input connector.
When using DC 12 V power (maximum DC 17 V), check the DC IN 12V terminal pin signal, and use the correct polarity. If the polarity is reversed, this could cause a fire or personal injury.
•While using both the AC and DC 12 V power supply, AC power supply is preferentially used. If the AC power supply is cut off (for example, when unplugging the AC power cord), the power supply automatically switches to the DC 12 V power supply.
pDC switch
Turns the DC 12 V power on or off.
•You need to press 
button on the front panel to turn on the monitor after turning on the DC switch.
•The monitor consumes the battery even while the monitor is on standby. To save battery life, turn off the DC switch.
qAC IN terminal
AC power input connector.
•Connect the provided AC power cord to an AC outlet.
•Attach the provided power cord holder to prevent accidental disconnection of the AC power cord (☞ page 9).
wPOWER switch
Turns the AC power on or off.
•You need to press 
button on the front panel to turn on the monitor after turning on the POWER switch.
eScrew holes for external battery attachment
Attach external battery for DC 12 V power supply by using 2 screw holes. Choose the appropriate screw holes from 1, 2, 3 or 4, according to the type of external battery.
•Use the Anton Bauer Dionic 90 (mount: QR
CAUTION
•Do not use the external battery for DC 24 V power supply.
•Use only the battery specified above. If a heavy battery is used, it may fall off depending on the way the monitor is used.
•When an external battery is attached, attach the ferrite core (provided) to the power cord from the mount as illustrated below.
Ex.: When the Anton Bauer mount (QR
Ferrite core
*Using the audio level meter
You can check the conditions of the current EMBEDDED AUDIO signals in the audio level meter. The setting for the level meter is selected in “LEVEL METER SETTING” (☞ “AUDIO SETTING” on page 11).