Onkyo BD-SP809 Turn on the Player and TV, Language Setting, Basic Operation, Troubleshooting

Turn on the Player and TV

After all of the necessary connections are complete, press [. (on/standby)] or [. ON/STANDBY] on the player to turn it on.

Turn on your TV and switch to the appropriate AV input (Refer to your TV’s operation manual). (This may be labelled “SOURCE”, “AV”, “AUX” or “SELECT”. etc.)

.(on/standby)

.ON/STANDBY

Language Setting

1 Press [HOME ] to display the home menu.

2 Use [Î/ ï/ Í/ Æ] to select “Settings”, then press [ENTER].

3 Use [Î/ ï] to select “Playback”, then press [ENTER].

4 Use [Î/ ï] to select “Player Menu”, then press

[ENTER].

5 Press [Î/ ï] to select the language you want to display on the screen, then press [ENTER].

	Player Menu	Auto
Video Out	Audio	Deutsch
Audio Out	Subtitle	English
HDMI	Disc Menu	Español
Playback	DivX Subtitle	Français
Network	BD Rating Level	Italiano
Others	DVD Rating Level	Nederlands
	Password Change	Polski

Basic Operation

1 Prepare the desired disc or content.

•Load a disc.

•Connect a USB flash drive into the USB input.

•Make a broadband Internet connection and settings.

NOTE:

•To remove the USB flash drive, in stop mode, pull it out slowly.

•Some USB device may not work with this player.

•If you use a USB extension cable, USB hub or USB card reader, the USB device may not be recognised.

•Virtual package/BD-LiveTMdata is saved in the USB flash drive connected to this player.

To enjoy these functions, connect a USB flash drive (1 GB or greater) to the USB input on this player.

2 Press [HOME ] to access the home menu.

3 Use [Î/ ï/ Í/ Æ] to select the desired media in the home menu, then press [ENTER].

4 Select the file type you want to play back, then press [ENTER].

e.g.)

Music

5 For “AVCHD”, playback will start automatically.

For “Music”, track / file list will be displayed. Select a group (folder) or track / file you want to play back, then press [Æ (play)] or [ENTER] to start playback.

6 Press [HOME] or [Ê(stop)] to exit playback.

NOTE:

•For more information, see “BASIC PLAYBACK” in the Instruction Manual.

Troubleshooting

Power

Problem	Possible causes and solutions
The player	• Is the AC cord firmly plugged into the
power cannot	AC outlet?
be turned on.	• Unplug the AC cord once, and wait
	for 5-10 seconds and then plug it in
	again.
The player	• Is “Auto Power Off” set to “On”?
power is turned	When “Auto Power Off” is set to “On”,
off.	the power will be automatically turned
	off after 30 continuous minutes of
	inactivity (no playback).

Basic Operation

Problem	Possible causes and solutions
The remote	• Use the remote control within its
control does not	operating range.
work.	• Replace the batteries.
Cannot operate	• Are you operating the player within the
the player.	specified operating temperature range?
The player	• Take out the disc and clean it.
cannot play a	• Make sure that the disc is loaded
disc.	properly (aligned in disc tray and
	label-side up).
	• Allow any condensation in or near the
	player to dry.
The disc is	• Make sure that the disc is loaded
automatically	properly (aligned in disc tray and
ejected after	label-side up).
closing the disc	• Take out the disc and clean it.
tray.	• Make sure that the disc is playable.
Video stops.	• Has the player been subjected to
	shock or impact? Are you using it in
	an unstable location? The player will
	stop if it senses shock or vibration.

Picture

Problem	Possible causes and solutions
No picture.	• Make sure that the cable is connected
	correctly.
Noise appears.	• If the TV supports Deep Color, use a
	recommended HDMI cable.
3D images	• Are a 3D compatible TV and 3D
cannot be	glasses used?
output to a TV.	• Make sure that the connected TV and
	the AV receiver are both 3D compatible.

Sound

Problem	Possible causes and solutions
No sound,	• If the volume of the TV or AV receiver
or sound is	is set to minimum, turn the volume up.
distorted.	• There is no sound during still mode,
	slow motion playback, fast forward
	and fast reverse.

6 Press [HOME ] to exit.