Vidikron Vision 20ET owner manual Ansi Lumen specification

Page 48

Additional Information

*ANSI Lumen specification:

This is the typical projector luminosity (brightness) specification found in most sales literature. This measurement is included in Vidikron literature to allow for direct comparison with other manufacturer's projectors. These measurements can be taken at 9,000 to 13,000 degree Kelvin to get expected performance data when the projector is used in professional, commercial, and industrial displays.

**CSMS Home Theater Calibration ANSI Lumen Specification:

These measurements are taken from the projector as setup in a home theater environment. The projector is calibrated to ISF specifications including setting the color temperature to 6500 degree Kelvin, the standard for reproducing video.

**CSMS Home Theater Calibration foot-Lambert (fL) Specification:

This is the unit of measurement used in commercial movie theaters to express image brightness. The Society of Motion Picture and Televi- sion Engineers (SMPTE) specifies 16 fL as the target image brightness for film-based projectors using an open gate (without film in the pro- jector). More importantly, today SMPTE specifies 12 fL as the target image brightness in Digital Cinema theaters using DLP™ technology. The foot-Lambert is dependant on screen size, screen gain, and projector light output.

All measurements are made at Vidikron to ANSI/NAPM IT7.228-1997 specifications using the Photo Research PR-650 SpectraColorimeter and Minolta LS-100 Light Meter, Video Essentials test DVD, and a Stewart Filmscreen StudioTech 130, 1.3 gain, 72-inch wide screen. The projector is calibrated to a color temperature of 6500º Kelvin and has a minimum of 150 hours of usage.

English

47

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Vision Model Vision Model 20ET Table of Contents Connecting Video Inputs Using the Menu Main Menu Picture Quality AdjustmentsImage Option Projector Status Install Service Image OptionsRisk of Electric Shock English Two Year Limited Warranty RIGHTS, Limits and Exclusions Features OverviewPIP/ PBP function Video MemoryProjector Exterior View Front / Upper SideFront Lamp Cover Control PanelRear / Bottom Side Controls and Functions Control PanelArrow c/e/d/f Zoom RingFocus Ring Connector Panel Remote Control Arrow c,e,d,fWide IntelliWide PIP Picture in PicturePOP Picture On Picture Installation Remote ControlConnect the Power Cord Adjust the Lens Zoom/Focus ringProjector Adjust the height Installation For Vision Model 20 With 1.71 2.06 Lens CeilingThrow Distance Chart For Vision Model 20 With 1.71 2.06 Lens Screen Hight Screen Width Min TD Max TD Vertical OffsetInstallation For Vision Model 20ET With 2.31 3.06 Lens CeilingSWx2.31 SWx3.06 Screen Width x Connecting Connecting Video Inputs Video / S-Video / Component Interlaced VideoDVD Player Progressive Component DTV Y/PB/PR DTV SourceRgbhv DTV RGB English Turning on the Power Basic OperationZoom/ Focusing Selecting Video MemorySetting Menu Selecting Input SourceSelecting Aspect Ratio PIP/ POP functionTurning off the Power Using the Menu MenuPicture Quality Adjustments Picture AdjustProjector Status Install Service Main MenuImage Options Input SelectAspect Ratio ScreensImage Option Memory StorePicture Adjust Image Options Install ServiceProjector Status Picture Configuration English Francais Espanol Deutsch ItalianoFloor Front Ceiling Front Floor Rear Ceiling Rear Service Blue EnableLamp Reset Timer White BalanceBlue Enable Reset Lamp TimerWhite Balance Blue Enable Additional Information Replace the Lamp Contact your Vidikron DealerTroubleshooting This unit does not turnRemote control does Power LED blinksNo picture Image is unstableSpecifications Vision Model 20/ Vision Model 20ET SpecificationsAnsi Lumen specification Dimensions RS-232 Setup RS-232C Control CodesPC Out Adapter Sub 9-pin female
Top Page Image Contents