Sharp XG-MB65X-L Rest your eyes occasionally, Avoid locations with extremes of tem- perature

Page 12

Observe the following safeguards when setting up your projector.

Caution concerning the lamp unit

■Potential hazard of glass par-

ticles if lamp ruptures. In case of lamp rupture, contact your nearest Sharp Autho- rized Projector Dealer or Ser- vice Center for replacement. See “Replacing the Lamp” on page 52.

Caution concerning the setup of the pro- jector

■For minimal servicing and to maintain high image quality, SHARP recommends that this projector be installed in an area free from humidity, dust and cigarette smoke. When the projector is subjected to these environments, the vents and lens must be cleaned more of- ten. As long as the projector is regularly cleaned, use in these environments will not reduce the overall operation life of the unit. Internal cleaning should only be performed by a Sharp Authorized Projector Dealer or Service Center.

When using the projector in high-altitude areas such as mountains (at altitudes of approximately 1,500 meters (4,900 feet) or more)

■When you use the projector in high-altitude areas with thin air, set “Fan Mode” to “High”. Neglecting this can affect the longevity of the optical system.

Warning about placing the projector in a high position

■When placing the projector in a high position, make certain it is carefully secure to avoid personal injury caused by the projector fall- ing down.

Do not subject the projector to hard im- pact and/or vibration.

■Protect the lens so as not to hit or damage the surface of the lens.

Rest your eyes occasionally.

■Continuously watching the screen for long hours will cause eye strain. Take regular breaks to rest your eyes.

Do not set up the projector in places ex- posed to direct sunlight or bright light.

■Position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.

Caution regarding placing of the projec- tor

■Place the projector on a level site within the adjustment range (8 degrees) of the adjust- ment foot.

■After the projector is purchased, a faint smell from the vent may appear when the power is first turned on. This is normal and is not a malfunction. It will disappear after the projec- tor is used for a while.

Avoid locations with extremes of tem- perature.

■The operating temperature of the projector is from 41°F to 95°F (+5°C to +35°C).

■The storage temperature of the projector is from –4°F to 140°F (–20°C to +60°C).

Do not block the exhaust and intake vents.

■Allow at least 11 13/16 inches (30 cm) of space between the exhaust vent and the nearest wall or obstruction.

■Be sure that the intake vent and the exhaust vent are not obstructed.

■If the cooling fan becomes obstructed, a pro- tection circuit will automatically put the pro- jector into standby mode to prevent overheat damage. This does not indicate a malfunc- tion. (See pages 50 and 51.) Remove the pro- jector power cord from the wall outlet and wait at least 10 minutes. Place the projector where the intake and exhaust vents are not blocked, plug the power cord back in and turn on the projector. This will return the projector to the normal operating condition.

8

Page 11 Page 13
Image 12
Page 11 Page 13
Contents XG-MB65X-L Model No Serial No This Apparatus Must be Earthed If YOU have ANY DOUBT, Consult a Qualified ElectricianPage IntroductionENGLISH A. onlySharp Electronics Corporation OnlyUsing the Menu Screen For Future ReferenceContents Reference Cleaning AccessoriesPower Sources Power-Cord ProtectionDamage Requiring Service Replacement PartsSafety Check OverloadingRest your eyes occasionally Avoid locations with extremes of tem- peratureDo not block the exhaust and intake vents Using the projector in other countries Temperature monitor functionOther connected equipment Accessories Optional accessoriesHeight 29 Adjust Part Names and FunctionsProjector Rear View Audio Input 1Audio Input Break Timer Picture ModeInserting the Batteries Attach the cover and slide it until it clicks into placeUsable Range Setup and Projection Quick StartSTANDBY/ON Upper side ProjectorSetting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount SetupProjection PRJ Mode Example Normal Mode Picture SizeProjection DistanceNormal Mode Stretch ModeScreen Size and Projection Distance Connections Input Terminals and Connectable Main EquipmentCOMPUTER-RGB/COMPONENT Samples of Cables for Connection Connecting to a Computer To audio output terminal To RGB output terminalComputer To INPUT1 terminal To Audio Terminal Connecting to Video Equipment When using an S-video cable INPUT3Connecting to a Monitor with RGB Input Terminal When using a composite video cable INPUT4Connecting the Power Cord Controlling the Projector by a ComputerAC socket To AC outlet Turning the Projector On/Off Turning the Projector onAbout the Setup Guide Adjusting the Projected Image Adjusting the FocusAdjusting the Picture Size Image ProjectionAdjusting the Height Use the rear adjustment foot to make the projector levelAdjust lever Make small adjustments Rear adjustment footSwitching the Input Mode Adjusting the VolumeAV Mute button Volume buttons Input buttons Press g Keystone to enter Keystone Correction mode Press P/Q or O/R to adjust Keystone CorrectionCorrecting Trapezoidal Distortion Press g KeystoneResize Mode Press HresizeVideo Operating with the Remote Control Auto Sync Auto Sync AdjustmentDisplaying and Setting the Break Timer Selecting the Picture ModeMenu Items Input 1 RGB/INPUT2 RGBInput 1 Component/INPUT Component/INPUT 3/INPUTItems you can set with the Help menu Help menu nUsing the Menu Screen Menu Selections AdjustmentsPress Q or O and select Picture to adjust Press BmenuTo adjust the projected image while watching it Press P or R and select Bright to adjustPress O or Q to adjust the item selected Press hENTERPicture Adjustment Picture menu Example Picture screen menu for Input 1 RGB mode2Adjusting the Image Menu operation nAdjusting the Projected Image SCR ADJ menu When using XG-MB65X-L or XG-MB55X-LSet Auto Keystone on the SCR ADJ menu to On Adjusting the Projected Image SCR ADJ menu Adjusting the Projector Function PRJ ADJ menu Select System Lock, then press hENTER or Q This function changes the fan rotation speedEnter the same keycode in Re- confirm Locking the Operation ButtonsATaking the Keylock off Troubleshooting with the Help menu Utilizing the Help menu func TionsMENU/HELP Maintenance Cleaning the projectorCleaning and Replacing the Dust Filters Cleaning the Dust FiltersRemove the filter holders Replacing the Dust Filters Replace the filter holdersReinforcement seal Maintenance Indicators Temperature warning indicator Lamp indicator Power indicatorPlease exercise care when Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Disconnect the power cordRemove the lamp unit cover Resetting the Lamp Timer Connecting Pin Assignments GNDRS-232C Specifications and Command Settings Return code 0DHCommands Control Contents Input 4 CLR Temp *2 OK or ERR Computer Compatibility Chart ComputerTroubleshooting 23-2647-51 For Sharp Assistance Specifications Audio OutputDimensions Index

XG-MB55X-L, XG-MB65X-L, XG-MB55X-L, XR-10X-L, XR-10S-L, XG-MB65X-L specifications

Sharp has long been a recognized leader in display technology, and its latest offerings, including the Sharp XG-MB65X-L, XG-MB55X-L, XR-10X-L, and XR-10S-L, continue to set the standard for high-quality visual performance in a variety of settings. These models cater to diverse needs, from business presentations to educational environments and high-end home theaters.

The Sharp XG-MB65X-L and XG-MB55X-L are standout models featuring a powerful blend of brightness and resolution. With vibrant colors and high contrast ratios, both projectors deliver stunning image quality, making them ideal for large audiences. Equipped with advanced DLP technology, these projectors ensure sharp, clear images even in well-lit environments. The 65-inch and 55-inch screen sizes respectively cater to different room sizes and audience requirements, without compromising on visual clarity.

Incorporating the latest in connectivity options, these models support various inputs, including HDMI, USB, and wireless capabilities, offering flexibility in how content is presented. This means that users can easily connect laptops, tablets, and even smartphones to stream presentations or videos seamlessly. Furthermore, the XG-MB series is designed with an eco-friendly mindset, featuring energy-saving modes that don't sacrifice performance.

On the other hand, the XR-10X-L and XR-10S-L are designed with portability in mind, making them perfect for on-the-go presentations. These models feature lightweight constructions and compact designs, allowing professionals to transport them easily. Despite their smaller sizes, they boast impressive brightness levels and image quality, ensuring that presentations remain impactful in various lighting conditions. The XR-10 series also benefits from user-friendly interfaces, simplifying the setup process and enabling quick adjustments.

Both series prioritize longevity and reliability, featuring extended lamp life and built-in maintenance alerts. This ensures minimal downtime and maximizes productivity, whether in corporate meetings or educational classrooms. Additionally, Sharp’s commitment to sound technology is evident, with each model equipped with built-in speakers that deliver clear audio to complement the exceptional visuals.

Overall, the Sharp XG-MB65X-L, XG-MB55X-L, XR-10X-L, and XR-10S-L projectors represent the pinnacle of Sharp's innovation in display technology. Their unique features, advanced technologies, and versatile characteristics make them suitable for a wide range of applications, ensuring that users can deliver their best presentations with confidence and ease.
Top Page Image Contents