E025 ± Logical unit not ready, manual intervention required.
E026 ± Logical unit not ready, format in progress.
E027 ± Logical unit not ready, operation in progress.
E028 ± Logical unit does not respond to selection.
E029 ± Multiple peripheral devices selected.
E030 ± Logical unit communication failure.
E031 ± Logical unit communication
E032 ± Logical unit communication parity error.
E033 ± Logical unit communication CRC error
E034 ± Track following error.
E035 ± Head select fault.
E036 ± Error log over¯ow.
E040 ± Write error.
E041 ± Compression check miscompare error.
E042 ± Data expansion occurred during compression.
E043 ± Block not compressible.
E044 ± Unrecovered read error.
E045 ± Read retries exhausted.
E046 ± Error too long to correct.
E047 ± Multiple read errors.
E048 ± Incomplete block read.
E049 ± No gap found.
E050 ± Miscorrected error.
E051 ± Decompression CRC error.
E052 ± Cannot decompress using declared algorithm.
E053 ± Block sequence error.
E054 ± Random positioning error.
E055 ± Mechanical positioning error.
E056 ± Positioning error detected by read of medium.
E057 ± Defect list error.
E058 ± Parameter list length error.
E059 ± Synchronous data transfer error.
E060 ± Invalid command operation code.
E061 ± Logical block address out of range.
E062 ± Invalid element address.
E063 ± Invalid ®eld in CDB.
E064 ± Logical unit not supported.
E065 ± Invalid ®eld in parameter list.
E066 ± Parameter not supported.
E067 ± Parameter value invalid.
E068 ± Threshold parameters not supported.
E069 ± Invalid release of active persistent reservation.
E070 ± Write protected.
E071 ± Hardware write protected.
E072 ± Logical unit software write protected.
E073 ± Associated write protect.
E074 ± Persistent write protect.
E075 ± Permanent write protect.
E076 ± Not ready to ready change, medium may have changed.
E077 ± Import or export element accessed.
E078 ± Power on, reset, or bus device reset occurred. E079 ± Power on occurred.
E080 ± SCSI bus reset occurred.
E081 ± Bus device reset function occurred.
E082 ± Device internal reset.
E083 ± Parameters changed.
E084 ± Mode parameters changed.
E085 ± Log parameters changed.
E086 ± Reservations preempted.
E087 ± Copy cannot execute because Store Controller cannot disconnect.
E088 ± Command sequence error.
E089 ± Overwrite error on update in place.
E090 ± Commands cleared by another initiator.
E091 ± Incompatible medium installed.
E092 ± Cannot read medium - unknown format.
E093 ± Cannot read medium - incompatible format.
E094 ± Cleaning cartridge installed.
E095 ± Cannot write medium - unknown format.
E096 ± Cannot write medium - incompatible format.
E097 ± Cannot format medium - incompatible medium.
E098 ± Cleaning failure.
E099 ± Medium format corrupted.
E100 ± Tape length error.
E101 ± Enclosure failure.
E102 ± Enclosure services failure.
E103 ± Unsupported enclosure function.
E104 ± Enclosure services unavailable.
E105 ± Enclosure services transfer failure.
E106 ± Enclosure services transfer refused.
E107 ± Rounded parameter.
E108 ± Saving parameters not supported.
E109 ± Sequential positioning error.
E110 ± Tape position error at
E112 ± Reposition error.
E113 ± Position past beginning of medium.
E114 ± Medium destination element full.
E115 ± Medium source element empty.
E116 ± Medium magazine not accessible.
Chapter 3. Using the Tape Drive 15
