Runco SP-42xa, SP-60xa, SP-50xa manual ISF CCC color mode is pre-set to approximately 3,200K

Page 55

Operation

front-panel STANDBY/ON indicator LED (Figure 2-1). When set to ON, the LED indicates operating status as follows:

•Lights green to indicate normal operation;

•Flashes green (once per second) when the AUTO OFF feature is active;

•Lights red to indicate that the CinemaWall is in standby mode;

•Flashes green or red (twice per second) to indicate an error condition.

When set to OFF, the LED lights red when the CinemaWall is in standby mode; otherwise, it is off.

ISF Settings: The CinemaWall provides two “color modes,” NORMAL and ISF CCC. This allows you to create two, independent sets of image quality settings and switch from one to the other by selecting a color mode.

Select ISF Settings from the Option menu. Then, press SET to select either NORMAL or ISF CCC. Any subsequent changes to image quality settings are stored and can be recalled by selecting that color mode.

The ISF CCC color mode is pre-set to approximately 3,200K.

Note

Runco Pro: Select Runco Pro from the Option menu to access these advanced image processing settings.

•Underscan: Underscan causes the outer edge of the display to appear beyond the normal effective data area for a video signal.

To use Underscan, select it from the Runco Pro menu and set it to ON. Then, exit the menu system and use the ASPECT RATIO remote control button to select Underscan mode.

•Display Profile: Select NORMAL or PURE to see the normal color gamut. Select MONOTONE to remove all color information from the image. Select HIGH CNT to increase the color temperature by approximately 2,000K.

•Signal Type: For most source material types, the appropriate Signal Type setting is MOTION. However, with certain interlaced and/or composite video images with few or no moving objects, STILL or NON-STD may yield better results.

Select Return to exit the Runco Pro menu.

FRC: Select FRC from the Option menu to enable frame rate conversion. Set FRC to NORMAL if you notice and want to minimize motion blur when viewing source material that originated from film. If frame rate conversion is not needed, set FRC to SCALER.

Power On Mode: Select Power On Mode from the Option menu to specify which input signal is displayed when you turn on the CinemaWall. You can also specify an initial audio volume level.

You can select a specific input or volume level (0 to 42). Or, select LAST to have the CinemaWall set the input and volume to what they were the last time it was turned off.

INSTALLER ADJ.

 

 

 

INPUT 3

PICTURE

SCREEN

SET-UP

OPTION

 

 

POWER ON MODE

 

 

 

 

 

SEAMLESS SW

: OFF

 

 

 

PICTURE ORIENT.

: OFF

 

 

 

FUNCTION RESET

 

 

 

SET

ENTER

 

 

MENU

EXIT

Seamless Switch: This feature allows for high-speed switching between any two

Runco CinemaWall SP Series Owner’s Operating Manual

45

Page 54 Page 56
Image 55
Page 54 Page 56
Contents SP-42 / SP-42xa SP-50 / SP-50xa SP-60 / SP-60xa Page For Plasma Displays Three Year Limited WarrantyRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions Table of Contents Serial Communications Maintenance and TroubleshootingSpecifications OperationList of Figures List of Figures About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories Controls and Functions Controls and IndicatorsCinemaWall at a Glance Display Stand SP-42, SP-50 and SP-60 respectively ConnectorsSP-50 Connector Panel Combination IN/OUT Main Power Switch CinemaWall Remote ControlSET Button Controls and Functions Remote Control InstallationOther surfaces Step Procedure For Details, refer to Quick SetupConsiderations InstallationVentilation Ambient LightInstallation Video Connections Connections to the CinemaWallAnalog RGB OUT Input 1 Connection Standby modeComposite or S-Video Input 3 Connection Computer/Video Signal Compatibility onComponent Video Input 4 Connection Attaching the Small Ferrite Cores to Audio Cables Audio Connections11. Audio Output Connection Connection RS-232 ControllerInstallation Operation Turning on the PowerChanging the OSD Language Setting the Computer Display Properties Selecting an Input Source Viewing Input Signal InformationChanging the Aspect Ratio Aspect Ratio Description Aspect Ratio SettingsPIX by PIX Image withinInstaller Adjust menu is intended for use by authorized Using the On-Screen MenusTrained service personnel only CinemaWall OSD Menu Structure Picture Main MenuTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Screen Set-Up PowerOFF DVI Setup Option Language Refer to Changing the OSD Language onScreen Maint. on Installer ADJ Input Option Installer Adjust ModeFAN Speed Auto ISF CCC color mode is pre-set to approximately 3,200K This action is not undoable. Proceed with caution Seamless Switch is not available when using PIPTo use PIP, press the Split button Using Picture-In-Picture PIPPIP Windows Swapping the MainViewing an Enlarged Area of the Display Enlarging One Part of the ScreenOperation Cleaning the Display Panel Body and Remote Control Maintenance and TroubleshootingCleaning Troubleshooting TipsFAN Failure OUT of Range Signal NGThermal Alert Shut DownExample RS-232 Connection and Port ConfigurationSerial Command Syntax Serial CommunicationsAspect Ratio Command Value Range DescriptionMinimum Maximum Input Select NoteAudio VideoPicture-in-Picture PIP MSTS09 MSTS08MSTS10 On left SET-UP Menu CommandsSets 2-screen operation to 2 Screen Side-by-side, full height main screenHigh LOWAverage Option Menu CommandsAuto Picture Menu Commands Installer Adjust Mode SET-UP Menu Commands Installer Adjust Mode Screen Menu Commands Installer Adjust ModeOption Menu Commands Installer Adjust Mode FMKS04 FMKS00FMKS02 FMKS034F 53 44 53 30 Sets OSD Display to OFF UPF Minimum Maximum Adjustment CommandsDW1 DWFCinemaWall Specifications SpecificationsDate of delivery to the end user Specifications are subject to change without noticeCinemaWall DimensionsCinemaWall Model SP-50 Dimensions with Optional Table Stand CinemaWall Model SP-60 Dimensions with Optional Table Stand Horiz Computer/Video Signal CompatibilityInput Refresh Rate Resolution Remarks56.0 45.1 Specifications Page Runco CL-810 Owner’s Operating Manual

SP-50xa, SP-60xa, SP-42xa specifications

Runco has long been recognized for its high-performance projection technologies, and the SP series, consisting of the SP-42xa, SP-50xa, and SP-60xa models, exemplifies this legacy. These projectors are designed for the discriminating home theater enthusiast who demands top-tier image quality, versatility, and innovative features.

The SP-42xa, with its 42-inch screen size, sets the stage for an immersive viewing experience. It boasts a native resolution of 1080p, delivering vibrant colors and extraordinary detail. This projector employs DLP technology, which enhances sharpness and clarity while minimizing motion blur. One notable feature of the SP-42xa is its Intelligent Lens System, which automatically adjusts the lens position to optimize the image based on the content being displayed.

The SP-50xa expands the capabilities with a larger 50-inch screen, perfect for medium-sized home theaters. It incorporates advanced color processing technology, which enhances color accuracy and brightness, providing a stunning visual experience for films and gaming. Additionally, the SP-50xa supports multiple aspect ratios, allowing users to enjoy content without letterboxing or cropping. Its built-in calibration settings facilitate precise adjustments suited to various lighting conditions, ensuring optimal performance in any environment.

The SP-60xa represents the pinnacle of the series with its impressive 60-inch display. This model features Runco's proprietary Vivix processing technology, which significantly enhances contrast and color depth. The SP-60xa provides support for high dynamic range (HDR), enabling deeper blacks and brighter highlights, which translates to a more lifelike picture. Furthermore, its CinemaScope aspect ratio capability offers an immersive cinematic experience, bridging the gap between home viewing and the theater.

All three models are equipped with extensive connectivity options, including HDMI and component inputs, making them compatible with a wide range of audio and video sources. User-friendly interfaces and remote controls simplify operation, allowing seamless integration with home automation systems.

In summary, the Runco SP-42xa, SP-50xa, and SP-60xa projectors collectively epitomize advanced projection technology combined with user-friendly features. With their focus on superior image quality, innovative adjustments, and versatility, these models are perfect for anyone seeking a premium home theater experience. Whether for movie nights or gaming marathons, the Runco SP series delivers an unparalleled visual feast that captivates and entertains.
Top Page Image Contents