Runco SP-42xa Command Value Range Description, Minimum Maximum, Input Select Note, Aspect Ratio

Page 64

Serial Communications

Table 6-1lists the CinemaWall serial command set. Except where indicated, adjustments made using serial commands are stored in the same memory as those made in Installer Adjust mode.

Table 6-1. Serial Commands

 

Command

Value Range

Description

 

 

 

 

 

 

 

 

ASCII

 

 

 

HEX

Minimum

Maximum

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Power

 

 

 

 

 

 

 

 

POF

 

50

4F 46

 

–

–

Power OFF.

 

 

 

 

 

 

 

 

PON

 

50

4F 4E

 

–

–

Power ON.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Input Select (Note 1)

 

 

 

 

 

 

 

 

IN1

 

49

4E

31

 

–

–

Switches the main screen to INPUT1.

 

 

 

 

 

 

 

 

 

IN2

 

49

4E

32

 

–

–

Switches the main screen to INPUT2.

 

 

 

 

 

 

 

 

 

IN3

 

49

4E

33

 

–

–

Switches the main screen to INPUT3.

 

 

 

 

 

 

 

 

 

IN4

 

49

4E

34

 

–

–

Switches the main screen to INPUT4.

 

 

 

 

 

 

 

 

 

IN5

 

49

4E

35

 

–

–

Switches the main screen to INPUT5.

 

 

 

 

 

 

 

 

 

INPS01

 

49

4E

50

53 30 31

–

–

Switches the main screen to INPUT1.

 

 

 

 

 

 

 

 

 

INPS02

 

49

4E

50

53 30 32

–

–

Switches the main screen to INPUT2.

 

 

 

 

 

 

 

 

 

INPS03

 

49

4E

50

53 30 33

–

–

Switches the main screen to INPUT3.

 

 

 

 

 

 

 

 

 

INPS04

 

49

4E

50

53 30 34

–

–

Switches the main screen to INPUT4.

 

 

 

 

 

 

 

 

 

INPS05

 

49

4E

50

53 30 35

–

–

Switches the main screen to INPUT5.

 

 

 

 

 

 

 

SSIS01

 

53

53 49 53 30 31

–

–

Switches the sub screen to INPUT1.

 

 

 

 

 

 

 

SSIS02

 

53

53 49 53 30 32

–

–

Switches the sub screen to INPUT2.

 

 

 

 

 

 

 

 

SWM

 

53

57 4D

 

–

–

Outputs main input to the full screen.

 

 

 

 

 

 

 

 

SWS

 

53

57 53

 

–

–

Outputs sub input to the full screen.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Aspect Ratio

 

 

 

 

 

 

 

 

AST

 

41

53 54

 

–

–

Executes AUTO SETUP on Input 1.

 

 

 

 

 

 

 

SZMS00

 

53

5A 4D 53 30 30

–

–

Sets the aspect ratio to PIX by PIX.

 

 

 

 

 

 

 

SZMS01

 

53

5A 4D 53 30 31

–

–

Sets the aspect ratio to Standard 4:3.

 

 

 

 

 

 

 

SZMS02

 

53

5A 4D 53 30 32

–

–

Sets the aspect ratio to ANAMORPHIC

 

 

 

 

 

 

 

 

16:9.

 

 

 

 

 

 

 

SZMS03

 

53

5A 4D 53 30 33

–

–

Sets the aspect ratio to LETTERBOX.

 

 

 

 

 

 

 

SZMS05

 

53

5A 4D 53 30 35

–

–

Sets the aspect ratio to VIRTUALWIDE.

 

 

 

 

 

 

 

 

 

Notes:

 

 

 

 

 

 

 

 

1.When making input-specific adjustments such as to image quality, screen position/size or audio sub-volume, select the input you wish to affect before making such adjustments.

2.These settings are not stored in memory.

54

Runco CinemaWall SP Series Owner’s Operating Manual

Page 63 Page 65
Image 64
Page 63 Page 65
Contents SP-42 / SP-42xa SP-50 / SP-50xa SP-60 / SP-60xa Page Three Year Limited Warranty For Plasma DisplaysRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions Table of Contents Maintenance and Troubleshooting SpecificationsOperation Serial CommunicationsList of Figures List of Figures Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Functions Controls and IndicatorsCinemaWall at a Glance Display Stand Connectors SP-42, SP-50 and SP-60 respectivelySP-50 Connector Panel Combination IN/OUT CinemaWall Remote Control Main Power SwitchSET Button Controls and Functions Installation Remote ControlOther surfaces Quick Setup Step Procedure For Details, refer toInstallation ConsiderationsAmbient Light VentilationInstallation Connections to the CinemaWall Video ConnectionsStandby mode Analog RGB OUT Input 1 ConnectionComputer/Video Signal Compatibility on Composite or S-Video Input 3 ConnectionComponent Video Input 4 Connection Audio Connections Attaching the Small Ferrite Cores to Audio Cables11. Audio Output Connection RS-232 Controller ConnectionInstallation Operation Turning on the PowerChanging the OSD Language Selecting an Input Source Viewing Input Signal Information Setting the Computer Display PropertiesChanging the Aspect Ratio Aspect Ratio Settings Aspect Ratio DescriptionImage within PIX by PIXInstaller Adjust menu is intended for use by authorized Using the On-Screen MenusTrained service personnel only CinemaWall OSD Menu Structure Main Menu PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Screen Set-Up PowerOFF DVI Setup Language Refer to Changing the OSD Language on OptionScreen Maint. on Option Installer Adjust Mode Installer ADJ InputFAN Speed Auto ISF CCC color mode is pre-set to approximately 3,200K Seamless Switch is not available when using PIP This action is not undoable. Proceed with cautionUsing Picture-In-Picture PIP To use PIP, press the Split buttonSwapping the Main PIP WindowsEnlarging One Part of the Screen Viewing an Enlarged Area of the DisplayOperation Maintenance and Troubleshooting CleaningTroubleshooting Tips Cleaning the Display Panel Body and Remote ControlOUT of Range Signal NG Thermal AlertShut Down FAN FailureRS-232 Connection and Port Configuration Serial Command SyntaxSerial Communications ExampleCommand Value Range Description Minimum MaximumInput Select Note Aspect RatioAudio VideoPicture-in-Picture PIP MSTS09 MSTS08MSTS10 SET-UP Menu Commands Sets 2-screen operation to 2 ScreenSide-by-side, full height main screen On leftLOW HighAverage Option Menu CommandsAuto Picture Menu Commands Installer Adjust Mode SET-UP Menu Commands Installer Adjust Mode Screen Menu Commands Installer Adjust ModeOption Menu Commands Installer Adjust Mode FMKS00 FMKS02FMKS03 FMKS044F 53 44 53 30 Sets OSD Display to OFF Minimum Maximum Adjustment Commands DW1DWF UPFSpecifications CinemaWall SpecificationsSpecifications are subject to change without notice Date of delivery to the end userDimensions CinemaWallCinemaWall Model SP-50 Dimensions with Optional Table Stand CinemaWall Model SP-60 Dimensions with Optional Table Stand Computer/Video Signal Compatibility Input Refresh Rate ResolutionRemarks Horiz56.0 45.1 Specifications Page Runco CL-810 Owner’s Operating Manual

SP-50xa, SP-60xa, SP-42xa specifications

Runco has long been recognized for its high-performance projection technologies, and the SP series, consisting of the SP-42xa, SP-50xa, and SP-60xa models, exemplifies this legacy. These projectors are designed for the discriminating home theater enthusiast who demands top-tier image quality, versatility, and innovative features.

The SP-42xa, with its 42-inch screen size, sets the stage for an immersive viewing experience. It boasts a native resolution of 1080p, delivering vibrant colors and extraordinary detail. This projector employs DLP technology, which enhances sharpness and clarity while minimizing motion blur. One notable feature of the SP-42xa is its Intelligent Lens System, which automatically adjusts the lens position to optimize the image based on the content being displayed.

The SP-50xa expands the capabilities with a larger 50-inch screen, perfect for medium-sized home theaters. It incorporates advanced color processing technology, which enhances color accuracy and brightness, providing a stunning visual experience for films and gaming. Additionally, the SP-50xa supports multiple aspect ratios, allowing users to enjoy content without letterboxing or cropping. Its built-in calibration settings facilitate precise adjustments suited to various lighting conditions, ensuring optimal performance in any environment.

The SP-60xa represents the pinnacle of the series with its impressive 60-inch display. This model features Runco's proprietary Vivix processing technology, which significantly enhances contrast and color depth. The SP-60xa provides support for high dynamic range (HDR), enabling deeper blacks and brighter highlights, which translates to a more lifelike picture. Furthermore, its CinemaScope aspect ratio capability offers an immersive cinematic experience, bridging the gap between home viewing and the theater.

All three models are equipped with extensive connectivity options, including HDMI and component inputs, making them compatible with a wide range of audio and video sources. User-friendly interfaces and remote controls simplify operation, allowing seamless integration with home automation systems.

In summary, the Runco SP-42xa, SP-50xa, and SP-60xa projectors collectively epitomize advanced projection technology combined with user-friendly features. With their focus on superior image quality, innovative adjustments, and versatility, these models are perfect for anyone seeking a premium home theater experience. Whether for movie nights or gaming marathons, the Runco SP series delivers an unparalleled visual feast that captivates and entertains.
Top Page Image Contents