Runco SP-50xa, SP-60xa, SP-42xa manual Option Installer Adjust Mode, Installer ADJ Input

Page 53

Operation

Auto Function: The CinemaWall can automatically switch to Input 1 or Input 4 when an image signal is detected at that input. To enable this feature, select Auto Function from the Option menu and set it to INPUT 1 or INPUT 4.

After Auto Function triggers an input switch, when the Input 1 or Input 4 signal is no longer present, the input source reverts to the previously-selected input.

In order for Auto Function to work correctly on Input 1, the input

Note signal must be RGB with composite or separate sync. Auto Function will not work with sync-on-green RGB or component signals.

When Auto Function is active, selecting an input manually causes

Auto Function to be temporarily disabled. If you cycle power to the

CinemaWall, Auto Function becomes active again.

Screen Maint.: When in Installer Adjust mode, select Screen Maint. from the Option menu to program the screen maintenance features of the CinemaWall to operate at regular intervals. This is useful for preventing image burn-in.

You can program the CinemaWall to switch inputs and/or replace the normal source signal with a white field, an inverse image or an “orbiting” image. You can specify a time of day and day of the week when you want this to take place.

To set up a screen maintenance program:

1.Press SET to select the DATE field for the first program. Press or to select one of the following:

•SUN, MON, TUE, WED, THU, FRI or SAT for a program that runs once only on the next occurrence of that day.

•* for a program that runs daily.

•*SUN, *MON, *TUE, *WED, *THU, *FRI or *SAT for a program that runs weekly on that day.

2.Press SET, then followed by SET again to set the program start time.

3.Press or to set the hour component of the start time.

4.Press , then or to set the minute component of the start time.

5.Press SET, then followed by SET again to set the program end time (repeat steps 3 and 4).

6.Press SET, then followed by SET again to specify an input associated with this program. Choose “–” to specify the input that was active when the CinemaWall was last powered off.

7.Press SET, then followed by SET again to select the PATTERN field for this program. Press or to select one of the following:

•Choose “–” to specify the function that was active when the CinemaWall was last powered off.

•Choose WHITE to display a white field.

•Choose INVERSE to display an inverse image.

•Choose ORBITER to display an “orbiting” image.

8.Press SET.

Option (Installer Adjust Mode)

INSTALLER ADJ.

 

 

 

INPUT 3

PICTURE

SCREEN

SET-UP

OPTION

 

 

PROGRAM TIMER

 

 

 

 

 

TEST PATTERN

: OFF

 

 

 

SIDEBAR ADJ.

 

 

 

 

 

 

BAUD RATE

 

: 9600BPS

 

 

ID NUMBER

 

: ALL

 

SET

ENTER

 

 

MENU

EXIT

PROGRAM TIMER

DATE

ON

OFF

INPUT

PATTERN

*

10:00

– –:– –

–

–

*

20:00

– –:– –

–

WHITE

*

– –:– –

21:00

–

–

–

– –:– –

– –:– –

–

–

–

– –:– –

– –:– –

–

–

–

– –:– –

– –:– –

–

–

–

– –:– –

– –:– –

–

–

RETURN

 

 

 

SET

ENTER

 

 

MENU EXIT

Runco CinemaWall SP Series Owner’s Operating Manual

43

Page 52 Page 54
Image 53
Page 52 Page 54
Contents SP-42 / SP-42xa SP-50 / SP-50xa SP-60 / SP-60xa Page For Plasma Displays Three Year Limited WarrantyRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions Table of Contents Specifications Maintenance and TroubleshootingOperation Serial CommunicationsList of Figures List of Figures About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories CinemaWall at a Glance Controls and IndicatorsControls and Functions Display Stand SP-42, SP-50 and SP-60 respectively ConnectorsSP-50 Connector Panel Combination IN/OUT Main Power Switch CinemaWall Remote ControlSET Button Controls and Functions Remote Control InstallationOther surfaces Step Procedure For Details, refer to Quick SetupConsiderations InstallationVentilation Ambient LightInstallation Video Connections Connections to the CinemaWallAnalog RGB OUT Input 1 Connection Standby modeComposite or S-Video Input 3 Connection Computer/Video Signal Compatibility onComponent Video Input 4 Connection Attaching the Small Ferrite Cores to Audio Cables Audio Connections11. Audio Output Connection Connection RS-232 ControllerInstallation Changing the OSD Language Turning on the PowerOperation Setting the Computer Display Properties Selecting an Input Source Viewing Input Signal InformationChanging the Aspect Ratio Aspect Ratio Description Aspect Ratio SettingsPIX by PIX Image withinTrained service personnel only Using the On-Screen MenusInstaller Adjust menu is intended for use by authorized CinemaWall OSD Menu Structure Picture Main MenuTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Screen OFF PowerSet-Up DVI Setup Option Language Refer to Changing the OSD Language onScreen Maint. on Installer ADJ Input Option Installer Adjust ModeFAN Speed Auto ISF CCC color mode is pre-set to approximately 3,200K This action is not undoable. Proceed with caution Seamless Switch is not available when using PIPTo use PIP, press the Split button Using Picture-In-Picture PIPPIP Windows Swapping the MainViewing an Enlarged Area of the Display Enlarging One Part of the ScreenOperation Cleaning Maintenance and TroubleshootingTroubleshooting Tips Cleaning the Display Panel Body and Remote ControlThermal Alert OUT of Range Signal NGShut Down FAN FailureSerial Command Syntax RS-232 Connection and Port ConfigurationSerial Communications ExampleMinimum Maximum Command Value Range DescriptionInput Select Note Aspect RatioPicture-in-Picture PIP VideoAudio MSTS10 MSTS08MSTS09 Sets 2-screen operation to 2 Screen SET-UP Menu CommandsSide-by-side, full height main screen On leftHigh LOWAuto Option Menu CommandsAverage Picture Menu Commands Installer Adjust Mode Option Menu Commands Installer Adjust Mode Screen Menu Commands Installer Adjust ModeSET-UP Menu Commands Installer Adjust Mode FMKS02 FMKS00FMKS03 FMKS044F 53 44 53 30 Sets OSD Display to OFF DW1 Minimum Maximum Adjustment CommandsDWF UPFCinemaWall Specifications SpecificationsDate of delivery to the end user Specifications are subject to change without noticeCinemaWall DimensionsCinemaWall Model SP-50 Dimensions with Optional Table Stand CinemaWall Model SP-60 Dimensions with Optional Table Stand Input Refresh Rate Resolution Computer/Video Signal CompatibilityRemarks Horiz56.0 45.1 Specifications Page Runco CL-810 Owner’s Operating Manual

SP-50xa, SP-60xa, SP-42xa specifications

Runco has long been recognized for its high-performance projection technologies, and the SP series, consisting of the SP-42xa, SP-50xa, and SP-60xa models, exemplifies this legacy. These projectors are designed for the discriminating home theater enthusiast who demands top-tier image quality, versatility, and innovative features.

The SP-42xa, with its 42-inch screen size, sets the stage for an immersive viewing experience. It boasts a native resolution of 1080p, delivering vibrant colors and extraordinary detail. This projector employs DLP technology, which enhances sharpness and clarity while minimizing motion blur. One notable feature of the SP-42xa is its Intelligent Lens System, which automatically adjusts the lens position to optimize the image based on the content being displayed.

The SP-50xa expands the capabilities with a larger 50-inch screen, perfect for medium-sized home theaters. It incorporates advanced color processing technology, which enhances color accuracy and brightness, providing a stunning visual experience for films and gaming. Additionally, the SP-50xa supports multiple aspect ratios, allowing users to enjoy content without letterboxing or cropping. Its built-in calibration settings facilitate precise adjustments suited to various lighting conditions, ensuring optimal performance in any environment.

The SP-60xa represents the pinnacle of the series with its impressive 60-inch display. This model features Runco's proprietary Vivix processing technology, which significantly enhances contrast and color depth. The SP-60xa provides support for high dynamic range (HDR), enabling deeper blacks and brighter highlights, which translates to a more lifelike picture. Furthermore, its CinemaScope aspect ratio capability offers an immersive cinematic experience, bridging the gap between home viewing and the theater.

All three models are equipped with extensive connectivity options, including HDMI and component inputs, making them compatible with a wide range of audio and video sources. User-friendly interfaces and remote controls simplify operation, allowing seamless integration with home automation systems.

In summary, the Runco SP-42xa, SP-50xa, and SP-60xa projectors collectively epitomize advanced projection technology combined with user-friendly features. With their focus on superior image quality, innovative adjustments, and versatility, these models are perfect for anyone seeking a premium home theater experience. Whether for movie nights or gaming marathons, the Runco SP series delivers an unparalleled visual feast that captivates and entertains.
Top Page Image Contents