Runco CW-42i manual Basic Operations

Page 17

BASIC OPERATIONS

» POWER

To turn the unit ON and OFF:

1.Plug the power cord into an active AC power outlet.

2.Press the POWER ON button (on the remote control or control panel) to turn on the unit. The monitor’s POWER/STANDBY indicator will light up (green) when the unit is on.

3.Press the POWER OFF button (on the remote control or control panel) to turn off the unit.

The monitor’s POWER/STANDBY indicator turns red and the standby mode is set (only when turning off the unit with the remote control).

» VOLUME

To adjust the sound volume:

1.Press and hold the VOLUME (+) button (on the remote control or the unit) to increase to the desired level.

2.Press and hold the VOLUME (-) button (on the remote control or the unit) to decrease to the desired level.

» MUTE

To cancel the sound:

Press the MUTE button on the remote control to cancel the sound; press again to restore.

» DISPLAY

To check the settings:

1.The screen changes each time the DISPLAY button is pressed.

2.If the button is not pressed for approximately three seconds, the menu turns off.

» TIMER OFF

To set the timer off:

The timer off can be set to turn the power off after 30, 60, 90 or 120 minutes

1.Press the AUTO OFF button to start the timer at 30 minutes.

2.Press the AUTO OFF button to the desired time.

3.The timer starts when the menu turns off.

30 60 90 120 0 ┐

TIMER OFF 30

To check the remaining time:

1.Once the off timer has been set, press the AUTO OFF button once.

2.The remaining time is displayed, then turns off after a few seconds.

3.When five minutes remain the remaining time appears until it reaches zero.

To cancel the off timer:

1.Press the AUTO OFF button twice in a row.

2.The off timer is canceled.

NOTE:

After the power is turned off with the timer off... A slight current is still supplied to the monitor. When you are leaving the room or do not plan to use the system for a long period of time, turn off the power of the monitor.

15

Page 16 Page 18
Image 17
Page 16 Page 18
Contents CW-42i Page Table of Contents Contents of the package » The features you’ll enjoy includeIntroduction Options» Warnings and Safety Precautions » PrecautionsImportant Information Risk of Electric Shock Do not OpenRecommendations to avoid or minimize phosphor burn-in » Plasma monitor cleaning procedure» To avoid damage and prolong operating life To Avoid Image BURN-IN Limited WarrantyWhat is Covered Under the Terms of this Limited Warranty Important Warranty Registration Effective Warranty DateContact a Runco Authorized Service Center to Obtain Service RIGHTS, Limits and ExclusionsVentilation Requirements for enclosure mounting HOW to Attach Options to the Plasma MonitorPart Names and Functions PowerInput Select / Exit MenuExternal Control AUDIO1, AUDIO2, AUDIO3Light ON/OFFExit AspectDVD 1 / HD1 Overall Functional DescriptionDigital Inputs » Plasma Connection Examples Installation» Connecting Your DVD Player » Connecting Your PC or Macintosh Computer» Connecting Your VCR or Laser Disc Player » Pin Assignments for 15-pin RGB analog » Pin Configuration of the RGB3 Connector DVI ConnectorBasic Operations Aspect Ratio Controls STD 43 mode 43 or Sxga » Wide Screen Operation with Computer SignalsWithin 3 seconds STD 43 Anamphc LTR BOX» Menu Operations OSD on Screen Display ControlsOSD On Screen Display Controls Language Use the and buttons to adjust the contrast » Picture Adjust Menu Adjusting the picturePicture adjustment screen Adjusting the computer imageTo set to CUSTOM1 Once the adjustment is completedNormal ISF DAY ISF NIT CUSTOM1 Film Types of picture modesReducing noise in the picture Once the setting is completedOFF VID NR1 VID NR2 VID NR3 Types of noise reductionSetting the color temperature Setting the KelvinAdjust the white balance using the and buttons Adjusting the Color to the Desired LevelAdjusting the white balance B GainGamma settings Making the Dither AdjustmentsChanging the Gamma Auto Still Motion DiffuseColor Chart settings Adjusting the ColorsDither settings Audio To continue adjusting the audio ... Repeat from stepTo set the Audio INPUT1 to VIDEO1 Setting the allocation of the audio connectorsSTD 43 ↔ Anamphc ↔ Vrtwide ↔ LTR BOX » Image Options MenuAdjusting the Computer When Computer is offAdjusting the position of the image Restoring the factory defaults settingsOn ↔ OFF » Install 1 Menu Setting the on-screen menuTo set the Display OSD to OFF To set the BNC Input mode to Comp Setting the BNC connectorsBNC Input settings RGB ↔ CompSetting a computer image to the correct RGB select screen Checking the signal being transmitted to RGB1 terminalTo set the RGB select mode to Auto Auto Still Motion RESIZE1 RESIZE2 DTVTo set the HD Type mode to 1080B Setting high definition images to the suitable screen size1080B 1035I 1080A RGB Type modesTo set the Input Skip mode to OFF Setting the Input SkipInput Skip settings OFF onUse the and buttons to select ON, then press the Menu button Resetting to the default valuesOFF » Install 2 Menu Setting the Auto Off for computer imagesTo turn the Auto Off function on Setting the picture to suit the movie Power / Standby indicatorPerform Steps 1-2 of PDP PROTECT, then LUM. Setting Luminance SettingOrbiter Adjust the Orbiter function manuallyOFF AUTO1 AUTO2 Manual DOTInverse Setting the time for InversePerform Steps 1-2 of PDP PROTECT, then Perform Steps 1-3 of INVERSE, thenSpeed Image SweepPerform Steps 1-3 of Image SWEEP, then To adjust the Sidebar ADJ Setting the Sidebar ADJ. for the sides of the screenUse the and buttons to adjust the Sidebar ADJ SoftenSetting the signal and black level for DVI signal Setting the screen size for S1/S2 video inputTo set PLUG/PLAY mode to STB/DVD Perform the following operationsPresent Time » Install 3 Menu Using the timerPerform Steps 1-2 of TIMER, then Date Program TimerSAT Function -- Orbiter Inverse White Image SweepRGB → Last ↔ VIDEO1 ↔ VIDEO2 ↔ VIDEO3 ← Setting the Default Input→ RGB3 ↔ RGB2 ↔ RGB1 ↔ HD1 ← Comp → LAST↔ VIDEO1 ↔ VIDEO2 ↔ VIDEO3 ←Menu button. The Install 3 screen appears Use Buttons to select Install 3, then pressEnabling/disabling the front panel controls Use Buttons to select Control LockTo set the IR Enable to OFF Enabling/disabling remote control wireless transmissionLoop Out Setting To set the Loop OUT to ON... UseTo set the ID number for the remote control ID Number SettingTo set the ID Number to O2 ALLUse this feature to configure a 2×2 or 3×3 video wall Video Wall SettingPosition DividerPerform Steps 1-2 of Video WALL, then Auto ID DISP. ModeOn Delay Power on delay Image AdjustOn Delay settings Use Buttons to select onLUM SET Link LUM SET Link settingsUse the and buttons to select Repeat Time Repeat Time RepeatDivider 1 4 Source→ English ↔ Deutsch ↔ Français ← → Italiano ↔ Español ← » Language Menu Setting the language for the menusTo select Deutsch Color System formats » Color System Menu Setting the video signal formatTo select 3.58NTSC Once you have checked the frequency Computer input signals supported by this system Table of Signals SupportedTable of Signals Supported Symptom Checks Remedy TroubleshootingDimensions Specifications Page

CW-42i specifications

The Runco CW-42i is a standout model in the realm of high-definition displays, known for its impressive performance and sleek design. As part of Runco's commitment to offering high-quality visual experiences, the CW-42i integrates advanced technologies tailored for both home theater enthusiasts and design-conscious consumers.

At its core, the Runco CW-42i boasts a stunning 42-inch diagonal screen, providing an optimal viewing experience for various settings, from intimate living rooms to dedicated home theaters. The display utilizes plasma technology, known for its ability to deliver deep blacks and vibrant colors, resulting in a rich and immersive viewing experience. With a native resolution of 1080p, the CW-42i ensures that visuals are sharp and detailed, whether you're watching movies, playing video games, or enjoying television shows.

One of the key features of the Runco CW-42i is its exceptional color accuracy and calibration capabilities. The display incorporates Runco's proprietary color processing technology, enabling it to reproduce colors with remarkable fidelity. Additionally, the CW-42i comes equipped with advanced calibration tools, allowing users to fine-tune their viewing experience to perfection. This level of customization ensures that every image looks as the creators intended, regardless of the content being viewed.

The CW-42i also distinguishes itself with its aesthetic appeal. With a modern and minimalistic design, it seamlessly integrates into any interior décor. The display features a slim profile and can be wall-mounted or placed on a stand, providing flexibility in installations. The bezels are narrow, offering a more immersive viewing area, ensuring that the attention remains on the screen rather than the frame.

In terms of connectivity, the Runco CW-42i is well-equipped to handle a variety of devices. It includes multiple HDMI ports, component inputs, and other essential connections, making it easy to link with Blu-ray players, gaming consoles, and set-top boxes. This versatility is crucial for users looking to build a comprehensive entertainment system.

Lastly, the CW-42i incorporates advanced sound technology, providing a comprehensive audio experience that complements the stunning visuals. Whether paired with an external audio system or used standalone, the display’s sound quality enhances the overall cinematic experience.

In summary, the Runco CW-42i is an exceptional display that combines cutting-edge technologies, versatile connectivity options, and a stylish design. Whether for home entertainment or professional presentations, the CW-42i is engineered to impress with stunning visuals and superior performance.
Top Page Image Contents