Runco CW-42i manual Setting the Kelvin, Setting the color temperature

Page 26

OSD (On Screen Display) Controls

Setting the KELVIN

Use this procedure to set color tone produced by the plasma display.

Example: Setting “6500K”

Press the MENU button on the remote control to display the MAIN MENU on the screen, then...

1.Use the and buttons to select “PICTURE ADJUST”, then press the MENU button. The “PICTURE ADJUST” screen appears.

2.Use the and buttons to select “KELVIN”.

3.Use the and buttons to select “6500K”.

The mode switches as follows when the and buttons are pressed: 5400K 6500K 8500K 9300K

* See below to set “WHITE BALANCE ”.

PICTURE ADJUST

2 / 2

PREVIOUS PG

KELVIN

GAMMA

DITHER COLOR CHART

: 6500K

:2.2

:AUTO

SEL. MENU/ENTER ENTER EXIT RETURN

*If neither the or button is pressed within 5 seconds, the current selection is set and the previous screen reappears.

4. Once the setting is completed...

Press the EXIT button to return to the main menu. To delete the main menu, press the EXIT button once more.

Information

 

■ Setting the color temperature

5400K

Redder

6500K

Slightly redder

8500K

Standard (slightly bluer)

9300K

Bluer

■ Restoring the factory default settings

Select “FACTORY” under the INSTALL 1 menu. Note that this also restores other settings to the factory defaults.

24

Page 25 Page 27
Image 26
Page 25 Page 27
Contents CW-42i Page Table of Contents Introduction » The features you’ll enjoy includeContents of the package OptionsImportant Information » Precautions» Warnings and Safety Precautions Risk of Electric Shock Do not OpenRecommendations to avoid or minimize phosphor burn-in » Plasma monitor cleaning procedure» To avoid damage and prolong operating life To Avoid Image BURN-IN Limited WarrantyWhat is Covered Under the Terms of this Limited Warranty Contact a Runco Authorized Service Center to Obtain Service Effective Warranty DateImportant Warranty Registration RIGHTS, Limits and ExclusionsHOW to Attach Options to the Plasma Monitor Ventilation Requirements for enclosure mountingInput Select / Exit PowerPart Names and Functions MenuAUDIO1, AUDIO2, AUDIO3 External ControlExit ON/OFFLight AspectDVD 1 / HD1 Overall Functional DescriptionDigital Inputs Installation » Plasma Connection Examples» Connecting Your DVD Player » Connecting Your PC or Macintosh Computer» Connecting Your VCR or Laser Disc Player » Pin Configuration of the RGB3 Connector DVI Connector » Pin Assignments for 15-pin RGB analogBasic Operations Aspect Ratio Controls Within 3 seconds » Wide Screen Operation with Computer SignalsSTD 43 mode 43 or Sxga STD 43 Anamphc LTR BOXOSD on Screen Display Controls » Menu OperationsOSD On Screen Display Controls Language Picture adjustment screen » Picture Adjust Menu Adjusting the pictureUse the and buttons to adjust the contrast Adjusting the computer imageNormal ISF DAY ISF NIT CUSTOM1 Film Once the adjustment is completedTo set to CUSTOM1 Types of picture modesOFF VID NR1 VID NR2 VID NR3 Once the setting is completedReducing noise in the picture Types of noise reductionSetting the Kelvin Setting the color temperatureAdjusting the white balance Adjusting the Color to the Desired LevelAdjust the white balance using the and buttons B GainChanging the Gamma Making the Dither AdjustmentsGamma settings Auto Still Motion DiffuseColor Chart settings Adjusting the ColorsDither settings To continue adjusting the audio ... Repeat from step AudioSetting the allocation of the audio connectors To set the Audio INPUT1 to VIDEO1» Image Options Menu STD 43 ↔ Anamphc ↔ Vrtwide ↔ LTR BOXAdjusting the position of the image When Computer is offAdjusting the Computer Restoring the factory defaults settingsOn ↔ OFF » Install 1 Menu Setting the on-screen menuTo set the Display OSD to OFF BNC Input settings Setting the BNC connectorsTo set the BNC Input mode to Comp RGB ↔ CompTo set the RGB select mode to Auto Checking the signal being transmitted to RGB1 terminalSetting a computer image to the correct RGB select screen Auto Still Motion RESIZE1 RESIZE2 DTV1080B 1035I 1080A Setting high definition images to the suitable screen sizeTo set the HD Type mode to 1080B RGB Type modesInput Skip settings Setting the Input SkipTo set the Input Skip mode to OFF OFF onResetting to the default values Use the and buttons to select ON, then press the Menu buttonOFF » Install 2 Menu Setting the Auto Off for computer imagesTo turn the Auto Off function on Power / Standby indicator Setting the picture to suit the movieLUM. Setting Luminance Setting Perform Steps 1-2 of PDP PROTECT, thenOFF AUTO1 AUTO2 Manual Adjust the Orbiter function manuallyOrbiter DOTPerform Steps 1-2 of PDP PROTECT, then Setting the time for InverseInverse Perform Steps 1-3 of INVERSE, thenSpeed Image SweepPerform Steps 1-3 of Image SWEEP, then Use the and buttons to adjust the Sidebar ADJ Setting the Sidebar ADJ. for the sides of the screenTo adjust the Sidebar ADJ SoftenTo set PLUG/PLAY mode to STB/DVD Setting the screen size for S1/S2 video inputSetting the signal and black level for DVI signal Perform the following operationsPresent Time » Install 3 Menu Using the timerPerform Steps 1-2 of TIMER, then SAT Program TimerDate Function -- Orbiter Inverse White Image Sweep→ RGB3 ↔ RGB2 ↔ RGB1 ↔ HD1 ← Setting the Default InputRGB → Last ↔ VIDEO1 ↔ VIDEO2 ↔ VIDEO3 ← Comp → LAST↔ VIDEO1 ↔ VIDEO2 ↔ VIDEO3 ←Enabling/disabling the front panel controls Use Buttons to select Install 3, then pressMenu button. The Install 3 screen appears Use Buttons to select Control LockLoop Out Setting Enabling/disabling remote control wireless transmissionTo set the IR Enable to OFF To set the Loop OUT to ON... UseTo set the ID Number to O2 ID Number SettingTo set the ID number for the remote control ALLVideo Wall Setting Use this feature to configure a 2×2 or 3×3 video wallPosition DividerPerform Steps 1-2 of Video WALL, then DISP. Mode Auto IDOn Delay settings Image AdjustOn Delay Power on delay Use Buttons to select onLUM SET Link settings LUM SET LinkDivider 1 4 Repeat Time RepeatUse the and buttons to select Repeat Time Source→ English ↔ Deutsch ↔ Français ← → Italiano ↔ Español ← » Language Menu Setting the language for the menusTo select Deutsch Color System formats » Color System Menu Setting the video signal formatTo select 3.58NTSC Once you have checked the frequency Table of Signals Supported Computer input signals supported by this systemTable of Signals Supported Troubleshooting Symptom Checks RemedyDimensions Specifications Page

CW-42i specifications

The Runco CW-42i is a standout model in the realm of high-definition displays, known for its impressive performance and sleek design. As part of Runco's commitment to offering high-quality visual experiences, the CW-42i integrates advanced technologies tailored for both home theater enthusiasts and design-conscious consumers.

At its core, the Runco CW-42i boasts a stunning 42-inch diagonal screen, providing an optimal viewing experience for various settings, from intimate living rooms to dedicated home theaters. The display utilizes plasma technology, known for its ability to deliver deep blacks and vibrant colors, resulting in a rich and immersive viewing experience. With a native resolution of 1080p, the CW-42i ensures that visuals are sharp and detailed, whether you're watching movies, playing video games, or enjoying television shows.

One of the key features of the Runco CW-42i is its exceptional color accuracy and calibration capabilities. The display incorporates Runco's proprietary color processing technology, enabling it to reproduce colors with remarkable fidelity. Additionally, the CW-42i comes equipped with advanced calibration tools, allowing users to fine-tune their viewing experience to perfection. This level of customization ensures that every image looks as the creators intended, regardless of the content being viewed.

The CW-42i also distinguishes itself with its aesthetic appeal. With a modern and minimalistic design, it seamlessly integrates into any interior décor. The display features a slim profile and can be wall-mounted or placed on a stand, providing flexibility in installations. The bezels are narrow, offering a more immersive viewing area, ensuring that the attention remains on the screen rather than the frame.

In terms of connectivity, the Runco CW-42i is well-equipped to handle a variety of devices. It includes multiple HDMI ports, component inputs, and other essential connections, making it easy to link with Blu-ray players, gaming consoles, and set-top boxes. This versatility is crucial for users looking to build a comprehensive entertainment system.

Lastly, the CW-42i incorporates advanced sound technology, providing a comprehensive audio experience that complements the stunning visuals. Whether paired with an external audio system or used standalone, the display’s sound quality enhances the overall cinematic experience.

In summary, the Runco CW-42i is an exceptional display that combines cutting-edge technologies, versatile connectivity options, and a stylish design. Whether for home entertainment or professional presentations, the CW-42i is engineered to impress with stunning visuals and superior performance.
Top Page Image Contents