Sharp AR-160, AR-161 specifications 10mm

Page 36

AR-161

1)Making of a test sheet

Make test sheet by drawing parallel lines at 10mm from the both ends of A3 (11" x 17") white paper as shown below. (These lines must be correctly parallel to each other.)

10mm

10mm

10mm

10mm

2)Make a normal (100%) copy of the test sheet on A3 (11" x 17") paper. (Fit the paper edge with the glass holding plate edge.)

3)Measure the distances (La, Lb, Lc, Ld) at the four corners as shown below.

 

 

La

 

 

 

Lc

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Lb

Ld

When La = Lb and Lc = Ld, no need to perform the procedures 4) and 5).

4)Move the mirror base B rail position up and down (in the arrow direction) to adjust.

•When La > Lb

Shift the mirror base B rail upward by the half of the difference of La – Lb.

•When La < Lb

Shift the mirror base B rail downward by the half of the difference of Lb – La.

Example: When La = 12mm and Lb = 9mm, shift the mirror base B rail upward by 1.5mm.

•When Lc > Ld

Shift the mirror base B rail downward by the half of the difference of Lc – Ld.

•When Lc < Ld

Shift the mirror base B rail downward by the half of the difference of Ld – Lc.

*When moving the mirror base rail, hold the mirror base rail with your hand.

<Adjustment specification>

La = Lb, Lc = Ld

5)After completion of adjustment, manually turn the mirror base drive pulley, scan the mirror base A and mirror base B fully, and check that the mirror bases are not in contact with each other.

*If the mirror base rail is moved extremely, the mirror base may be in contact with the frame or the original glass. Be careful to avoid this.

(5)Main scanning direction (FR direction) magnification ratio adjustment (SIM 48-1)

Note: Before performing this adjustment, be sure to check that the CCD unit is properly installed.

1) Put a scale on the original table as shown below.

2)Execute SIM 48-1.

3)After warmup, shading is performed and the current set value of the main scanning direction magnification ratio is displayed on the display section in 2 digits.

4)Select the mode and press the start key again.

5)Auto correction mode (AE lamp ON)

The mirror unit moves to the shading position, and the reference width of the reference white plate is scanned, and the correction value is automatically calculated from that scanned value.

The correction value is displayed and a copy is made.

6)Compare the scale image and the actual scale.

If a fine adjustment is required, switch to the manual correction mode with the magnification ratio display key and perform fine adjustment.

7)Manual correction mode (TEXT lamp ON) Enter the set value and press the start key. The set value is stored and a copy is made.

7 – 6

Page 35 Page 37
Image 36
Page 35 Page 37
Contents AR-160 Class Laser Product Laser Klasse Contents General Specifications Warmup time Copy magnification ratioPrint density Print areaOther specifications Power sourcePower consumption Machine compositionConsumable Parts Supply system tableAsia, Southeast Asia Hong Kong / China Environment conditions Production number identificationConsumable parts recycling procedure Drum unit AR-161 Attach the main charger External Views and Internal Structures AppearanceInternal Operation Section Motor, solenoid, clutch Sensor, switch PWB unit Cross sectional view 1 4 1Unpacking and Installation Installation of machineInstallation of developing cartridge Installing conditionsRemoval and storage of fixing screw Changing the copy paper size in the tray Operational Descriptions Outline of operationScanner section Process section Basic structure of scanner sectionBasic structure CCD PWBOperation cycle Outline of print processActual print process ChargingCleaning ExposureTransfer Developing DC biasLaser unit Optical discharge Semiconductor laserPWB Paper feed section Laser beam pathBrief descriptions of operations Cassette paper feed operationFusing section Adjustments Adjustment item listCopier adjustment Process sectionDeveloping bias voltage adjustment SIM Grid bias voltage adjustment SIM 8-2, SIMImage position adjustment SIM 50-1/SIM Mechanism sectionPaper off center adjustment AR-161 Main scanning direction FR direction distortion adjustment 10mm Off center adjustment SIM 50-13, SIM OC mode in copyingImage density adjustment Original sensor adjustment SIMCopy mode SIM SPFEntering the simulation mode Cancelling the simulation modeSimulation List of simulationsContents of simulations Main Sub Contents Details of operation Initial Value Sheets Free 999999 sheets Mini maintenance counter When a is displayed Set value is stored AE LED Text LEDOC mode sub scanning Key operation User Program User program functionsSetting change procedure Department counter settingDepartment counter setting/cancel Function code Department number recording Function codeDepartment number change Function code Department number delete Function codeTrouble Code List FAXCCD LSUMaintenance Maintenance tableDisassembly and Assembly High voltage sectionOptical section Fusing unit removal Copy lamp unitCopy lamp Lens unit Thermostat Thermistor Heater lampFront cabinet unit, right cabinet disassembly Paper exit sectionUpper heat roller Separation pawl Lower heat roller Paper exit unit Paper exit roller Transport roller Optical frame unit MCULSU Tray paper feed section/Paper transport section Intermittent frame unitDrive unit Manual multi paper feed section Manual multi paper feedManual transport clutch Manual paper feed clutchPower section Power unitManual transport roller/Manual paper feed roller Multi feed solenoidDeveloping section Waste toner box Developing box MG rollerDeveloping doctor MC holder unit Cleaning blade Block diagram Electrical SectionOutline Block diagram MCU CPU HD6412351IF a. pin/signal tableOUT POWIRQ5 Spfcover IRQ6 OccoverIRQ7 MHP IRQ3 SpfpaperFaxpage Ready OUTPwoff OUT Scansp OUTPin/signal table Image Asic HG73C039FDOutline Fault OUT MDATA10 IN/OUT MDATA9MDATA8 IN/OUT MDATA7 MDATA6 IN/OUTSOE0 OUT SWE0 OUTSCS0 OUT SAD0 OUTO Asic GND POW VCC PMC4POUT3 Dpxdb PWM0POUT PfanmdPWM1POUT Tfanmd P0OUT8 SophiaP1IN8 Esready P1IN9 FaxreadyTest PclreadyRstb Reset PMC3TCLK Lftclk OUTPMC3DREQB OUT PMC4TCLK OUTReset circuit Main motor drive circuitMirror motor circuit CCD PWB Toner supply motor drive circuitCircuit Diagram MCU MCU MCU MCU MCU MCU MCU MCU MCU Operation PWB1 Operation PWB2 Operation PWB3 Electronic Sort KEY PWB Actual Wiring Diagram Actual Wiring Diagram 2/3 Actual Wiring Diagram 3/3 AR-161 Copyright 1998 by Sharp Corporation

AR-160, AR-161 specifications

The Sharp AR-161 and AR-160 are monochrome multifunction printers that have made a mark in the office equipment landscape with their impressive features, technologies, and characteristics. Both devices are designed to cater to the needs of small to medium-sized businesses that require reliable, efficient, and compact systems for their printing, copying, and scanning needs.

One of the main features of the Sharp AR-161 and AR-160 is their impressive speed. The AR-161 can produce up to 16 pages per minute (ppm), while the AR-160 offers a slightly lower output at 15 ppm. This makes both models suitable for environments where quick document turnaround is essential. Additionally, both machines have a warm-up time of approximately 20 seconds, ensuring minimal downtime when starting up.

In terms of paper handling, both models come equipped with a 250-sheet paper drawer and a 100-sheet bypass tray, allowing for a variety of media types and sizes. The automatic document feeder (ADF) can accommodate up to 50 sheets, making it easier to handle multi-page documents without manual intervention. This feature enhances workflow efficiency significantly, particularly in busy office settings.

The Sharp AR-161 and AR-160 utilize advanced copying technologies, including a high-resolution scanning capability of up to 600 x 600 dpi. This means that documents are reproduced with clarity and detail, making them suitable for professional presentations and reports. The devices also offer various copying options, such as zoom, collation, and reduction/enlargement, providing versatility for different copying tasks.

Both models are equipped with Sharp's innovative ImageSEND technology, which allows users to scan documents directly to email, network folders, or USB drives with ease. This feature enhances productivity by streamlining the scanning process, ensuring that documents can be shared quickly and efficiently.

Furthermore, energy efficiency is a hallmark of the Sharp AR-161 and AR-160, as both models are ENERGY STAR qualified. This means they are designed to use less energy, helping businesses reduce their environmental impact while also saving on operational costs.

In conclusion, the Sharp AR-161 and AR-160 combine speed, versatility, and energy efficiency in a sleek design. Their advanced copying technologies and smart features make them ideal choices for businesses seeking reliable multifunction devices that can enhance productivity without compromising on quality.
Top Page Image Contents