Sharp AR-160, AR-161 specifications Setting change procedure, Department counter setting

AR-161

2. Setting change procedure

Example: Changing the time for operating the auto clear function (from 60 sec to 120 sec)

1)Press and hold the density adjustment key for 5 sec to start setting.

•When lamps start blinking at the same time, the copy quantity display shows "--" the digit of 10 blinking.

2)Select the function code with the numeric key.

•The code of the selected function is displayed (blinking) on the digits of 10 and 100.

•For auto clear, select 1.

•Select the suitable code according to the table below.

User program setting contents

Function	Function code	Setting code
Auto clear	1	0 (Cancel)
		1 (30 sec)
		∗2 (60 sec)
		3 (90 sec)
		4 (120 sec)
Pre-heat	2	0 (Cancel)
		1 (30 sec)
		2 (60 sec)
		∗3 (90 sec)
		4 (120 sec)
Auto power shut off passing	3	∗1 (30 sec)
time (*2)
		2 (60 sec)
		3 (90 sec)
		4 (120 sec)
		5 (240 sec)
Stream feeding mode	4	∗0 (Cancel)
		1 (Setting)
Auto power shut off function	5	0 (Cancel)
setting (*2)
		∗1 (Setting)
2 in 1/4 in 1 solid frame setting	6	∗0 (Cancel)
		1 (Setting)
Rotation copy	7	0 (Cancel)
		∗1 (Setting)
Paper auto selection	8	0 (Cancel)
		∗1 (Setting)
Tray auto selection	9	0 (Cancel)
		∗1 (Setting)
Department counter (*1)	10 ~ 15
Edge erase	16	0 (0mm)
		1 (5mm)
		∗2 (10mm)
		3 (15mm)
		4 (20mm)
2 in 1 layout (*3)	17	∗1 (Pattern A)
		2 (Pattern B)
4 in 1 layout (*3)	18	∗1 (Pattern A)
		2 (Pattern B)
		3 (Pattern B)
		4 (Pattern B)

∗Setting at the factory shipping

*1. For the setting procedure, refer to "3. Department counter."

*2. With the auto power shut off canceled (function code "5", set code "0", auto power shut off time setting code "3"), the mode enters the auto power shut off setting mode automatically.

*3. For the layout pattern, refer to page 9-1.

•The number of the selected function blinks on the digit of 1 or the copy quantity display.

Cancel: When any key is pressed by mistake, press the clear key and press the proper key.

3)Press the START key.

•The selected function code is changed from blinking to lighting.

•The currently set code blinks on the digit of 1.

4)Select the setting code with the numeric key.

•For setting to 80 sec, select ⎡3⎦.

•Make setting referring to the setting codes of "User program setting contents."

Cancel: When any wrong key is pressed, press the clear key and resume from procedure 2.

5) Press the START key,

•The selected setting code is changed from blinking to lighting. The setting is completed with the above operation.

Memo: To set another function, press the clear key after this proce- dure and resume from procedure 2.

6)Press the density adjustment key to end the setting.

• lamps go off. The copy quantity display returns to the normal display.

3. Department counter setting

Note: The department counter is effective only in copying. Counting is not made in FAX and printer output.

When the department counter is set, the copy count for each depart- ment (max. 20 dept.) can be made and displayed when necessary.

With the department counter set, copying cannot be made unless the registered number (password number of 3 digits) is entered.

1)Press and hold the density adjustment key for about 5 sec to start setting.

• lamps start blinking at the same time, and the copy quantity display displays "--" and the digit of 10 blinks.

2)Select the function code with the numeric key.

•Refer to the function code for setting.

Setting contents of department counters

Function	Function code
Setting content	10	Department counter
		setting or cancel. Factory
		setting: Cancel
Department	11	Department number
counter		recording.
setting/cancel		Max. 20 department can
		be recorded.
Department	12	Recorded department
number recording		number is changed.
Department	13	Recorded number is
number delete		deleted.
Copy quantity	14	The copy quantity in each
display (Total)		department is displayed.
		The count is made up to
		49,999 sheets. From that,
		counting is started from 0.
Copy quantity	15	The counted copy quantity
delete (Total		is canceled. The count of
delete)		each department or that of
		all the departments can be
		deleted.

•The entered number blinks on the digits of 100 and 10 on the copy quantity display.

Cancel: When a wrong key is pressed, press the clear key and enter the correct key.

9 – 2