Sharp AR-161, AR-160 Unpacking and Installation, Installation of machine, Installing conditions

Page 21

[5]UNPACKING AND INSTALLATION

1. Installation of machine

A. Installing conditions

Since the machine performance is largely affected by the installing place conditions, take enough considerations on the following items

1) Environment

•Avoid installation at a place with direct sunlight. If not, the plastic parts may be deformed.

•Avoid installation near a heater, a humidifier, or an air conditioner where humidity and temperature are extremely high or low. If not, paper may be dampened and dew is formed inside the machine, causing paper jam or dirty copies.

•Avoid installation at a dusty place. If dust enters the machine, dirty copy or a trouble may be caused.

•Avoid installation at a place with vibrations. If not, a machine trouble may be caused.

•Avoid installation at a poorly ventilated place.

•Avoid installation at a place that is filled with ammonium gas. If the copier is installed near a diazo-copier, dirty copies may be resulted.

2) Space around the copier

•Allow a space of more than between the copier rear side and the wall.

3) Power source

•Use an exclusive-use power outlet of 15A and 100V or more. If the power plug of this machine is inserted into a power outlet com- monly used with other illumination units, flickers of the lamp may be resulted. Use a power outlet which is not used commonly with any illumination units.

•Avoid complex wiring.

4) Grounding wire connection.

•To avoid danger, be sure to connect a grounding wire. If no groun ing wire is connected and a leakage occurs, a fire or an electric shock may be resulted.

2.Removal of protective material and fixing screw

1)Remove all tapes and protective material.

•Remove all tapes, then open the document cover and remove the protective material of sheet shape

2)Remove the fixing screw.

•Use a coin to remove the fixing screw.

•The fixing screw is required when transporting the machine. Keep it in the tray. (Refer to the later description.)

AR-161

3. Installation of developing cartridge

1) Open the manual paper feed tray.

2) Lift the knob and slide the side cover gently.

3)Open the front cover.

• Hold the both edge gently and open the front cover.

4)Remove the screw from the upper section of the insertion port of the developer cartridge.

5)Shake a new developer cartridge a few times as shown.

• Shake it horizontally as shown with the arrow.

5 – 1

Page 20 Page 22
Image 21
Page 20 Page 22
Contents AR-160 Class Laser Product Laser Klasse Contents General Specifications Copy magnification ratio Warmup timePrint density Print areaPower source Other specificationsPower consumption Machine compositionConsumable Parts Supply system tableAsia, Southeast Asia Hong Kong / China Production number identification Environment conditionsConsumable parts recycling procedure Drum unit AR-161 Attach the main charger External Views and Internal Structures AppearanceInternal Operation Section Motor, solenoid, clutch Sensor, switch PWB unit 1 4 1 Cross sectional viewInstallation of machine Unpacking and InstallationInstallation of developing cartridge Installing conditionsRemoval and storage of fixing screw Changing the copy paper size in the tray Operational Descriptions Outline of operationScanner section Basic structure of scanner section Process sectionBasic structure CCD PWBOutline of print process Operation cycleActual print process ChargingExposure CleaningTransfer Developing DC biasLaser unit Optical discharge Semiconductor laserPWB Laser beam path Paper feed sectionBrief descriptions of operations Cassette paper feed operationFusing section Adjustment item list AdjustmentsCopier adjustment Process sectionGrid bias voltage adjustment SIM 8-2, SIM Developing bias voltage adjustment SIMImage position adjustment SIM 50-1/SIM Mechanism sectionPaper off center adjustment AR-161 Main scanning direction FR direction distortion adjustment 10mm OC mode in copying Off center adjustment SIM 50-13, SIMOriginal sensor adjustment SIM Image density adjustmentCopy mode SIM SPFCancelling the simulation mode Entering the simulation modeSimulation List of simulationsContents of simulations Main Sub Contents Details of operation Initial Value Sheets Free 999999 sheets Mini maintenance counter When a is displayed Set value is stored Text LED AE LEDOC mode sub scanning Key operation User program functions User ProgramDepartment counter setting Setting change procedureDepartment number recording Function code Department counter setting/cancel Function codeDepartment number change Function code Department number delete Function codeFAX Trouble Code ListLSU CCDMaintenance table MaintenanceDisassembly and Assembly High voltage sectionOptical section Fusing unit removal Copy lamp unitCopy lamp Lens unit Heater lamp Thermostat ThermistorFront cabinet unit, right cabinet disassembly Paper exit sectionUpper heat roller Separation pawl Lower heat roller Paper exit unit Paper exit roller Transport roller Optical frame unit MCULSU Tray paper feed section/Paper transport section Intermittent frame unitDrive unit Manual multi paper feed Manual multi paper feed sectionManual paper feed clutch Manual transport clutchPower unit Power sectionManual transport roller/Manual paper feed roller Multi feed solenoidDeveloping section Waste toner box Developing box MG rollerDeveloping doctor MC holder unit Cleaning blade Block diagram Electrical SectionOutline CPU HD6412351IF a. pin/signal table Block diagram MCUOUT POWIRQ6 Occover IRQ5 SpfcoverIRQ7 MHP IRQ3 SpfpaperReady OUT FaxpagePwoff OUT Scansp OUTPin/signal table Image Asic HG73C039FDOutline MDATA10 IN/OUT MDATA9 Fault OUTMDATA8 IN/OUT MDATA7 MDATA6 IN/OUTSWE0 OUT SOE0 OUTSCS0 OUT SAD0 OUTO Asic PWM0POUT Pfanmd GND POW VCC PMC4POUT3 DpxdbPWM1POUT Tfanmd P0OUT8 SophiaP1IN9 Faxready P1IN8 EsreadyTest PclreadyPMC3TCLK Lftclk OUT Rstb ResetPMC3DREQB OUT PMC4TCLK OUTReset circuit Main motor drive circuitMirror motor circuit Toner supply motor drive circuit CCD PWBCircuit Diagram MCU MCU MCU MCU MCU MCU MCU MCU MCU Operation PWB1 Operation PWB2 Operation PWB3 Electronic Sort KEY PWB Actual Wiring Diagram Actual Wiring Diagram 2/3 Actual Wiring Diagram 3/3 AR-161 Copyright 1998 by Sharp Corporation

AR-160, AR-161 specifications

The Sharp AR-161 and AR-160 are monochrome multifunction printers that have made a mark in the office equipment landscape with their impressive features, technologies, and characteristics. Both devices are designed to cater to the needs of small to medium-sized businesses that require reliable, efficient, and compact systems for their printing, copying, and scanning needs.

One of the main features of the Sharp AR-161 and AR-160 is their impressive speed. The AR-161 can produce up to 16 pages per minute (ppm), while the AR-160 offers a slightly lower output at 15 ppm. This makes both models suitable for environments where quick document turnaround is essential. Additionally, both machines have a warm-up time of approximately 20 seconds, ensuring minimal downtime when starting up.

In terms of paper handling, both models come equipped with a 250-sheet paper drawer and a 100-sheet bypass tray, allowing for a variety of media types and sizes. The automatic document feeder (ADF) can accommodate up to 50 sheets, making it easier to handle multi-page documents without manual intervention. This feature enhances workflow efficiency significantly, particularly in busy office settings.

The Sharp AR-161 and AR-160 utilize advanced copying technologies, including a high-resolution scanning capability of up to 600 x 600 dpi. This means that documents are reproduced with clarity and detail, making them suitable for professional presentations and reports. The devices also offer various copying options, such as zoom, collation, and reduction/enlargement, providing versatility for different copying tasks.

Both models are equipped with Sharp's innovative ImageSEND technology, which allows users to scan documents directly to email, network folders, or USB drives with ease. This feature enhances productivity by streamlining the scanning process, ensuring that documents can be shared quickly and efficiently.

Furthermore, energy efficiency is a hallmark of the Sharp AR-161 and AR-160, as both models are ENERGY STAR qualified. This means they are designed to use less energy, helping businesses reduce their environmental impact while also saving on operational costs.

In conclusion, the Sharp AR-161 and AR-160 combine speed, versatility, and energy efficiency in a sleek design. Their advanced copying technologies and smart features make them ideal choices for businesses seeking reliable multifunction devices that can enhance productivity without compromising on quality.
Top Page Image Contents