NAD T 754 owner manual Safety Information, Explanation of Graphical Symbols

Page 2

SAFETY INFORMATION

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

PRECAUTIONS

Read the Operating Instructions carefully and completely before operating the unit. Be sure to keep the Operating Instructions for future reference. All warnings and cautions in the Operating Instructions and on the unit should be strictly followed, as well as the safety suggestions below.

INSTALLATION

1Water and Moisture - The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

2Heat - Do not use this unit near sources of heat, including heating vents, stoves, or other appliances that generate heat. It also should not be placed in temperatures less than 5°C (41°F) or greater than 35°C (95°F).

3Mounting surface - Place the unit on a flat, even surface.

4Ventilation - The unit should be situated with adequate space around it so that proper ventilation is assured. allow 10 cm (4 in.) clearance from the rear and the top of the unit, and 5 cm (2 in.) from each side. - Do not place on a bed, rug, or similar surface that may block the ventilation openings. - Do not install the unit in a bookcase cabinet, or airtight rack where ventilation may be impeded.

5Objects and liquid entry - Take care that objects or liquids do not get inside the unit through the ventilation openings.

6Carts and stands - When placed or mounted on a stand or cart, the unit should be moved with care. Quick

stops, excessive force, and uneven surfaces may cause the unit and cart to overturn or fall.

7 Wall or ceiling mounting - The unit should not be mounted on a wall or ceiling, unless specified in the Operating Instructions.

WARNING! TO REDUCE THE RISK OF FIRE OR ELECTRONIC SHOCK, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE

SLOT, FULLY INSERT.

This product is manufactured to comply with the radio interference requirements of EEC DIRECTIVE 89/366/EEC, 92/31/EC and 93/68/EEC

NOTES ON ENVIRONMENTAL PROTECTION

At the end of its useful life, this product must not be disposed of with regular household waste but must be returned to a collection point for the recycling of electrical and electronic equipment. The symbol on the product, user's manual and packaging, point this out.

The materials can be reused in accordance with their markings. Through re-use, recycling of raw materials, or other forms of recycling of old products, you are making an important contribution to the protection of our environment.

Your local administrative office can advise you of the responsible waste disposal point.

Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories.

”DTS“, ”DTS-ES“ and ”Neo:6“ are trademarks of Digital Theater Systems, Inc.

2

Image 2
Contents 754 Safety Information Explanation of Graphical SymbolsDamage Requiring Service Electric PowerMaintenance Do not Attempt to Service the Unit Yourself OWNER’S RecordTable of Contents Getting the Most from the NAD T Using the HTR 2 Remote ControlTroubleshooting Specifications WHAT’S in the BOX Unpacking and SetupConnecting AM Antenna Choosing a LocationEase of USE About the TR.S., Matrix and Digital Surround IntegrationAbout the HTR 2 System Remote Control UpgradabilityQuickstart Play a DVD MovieFront Panel SearchDigital Input Jack Rear Panel +12V Trigger IN/OUTRear Panel Dealing with HUM and Noise Setting UP the TGetting Started About the ON-SCREEN Displays OSD and FRONT-PANEL Readout Input SetupInput Settings Display the OSDListening Mode Speaker SetupSpeaker Settings Setting Channel Balance CHANNEL-BALANCE Test SetupUsing AN SPL Meter Setting Speaker DistanceCreating Presets Recalling PresetsUsing the T Selecting Radio Presets Tuning StationsSetting Radio Presets Choosing the FM Mute / ModeDTS ES Matrix DTS ES Expanded Surround DTS ESDTS-ES Discrete DTS NEO 6 SurroundDolby PRO Logic II Movie Dolby PRO LogicDolby PRO Logic II Surround Dolby PRO Logic II MusicDTS Displaying the Signal ModeSelecting Listening Modes Adjusting Listening Modes DTS NeoTo Adjust Channel Levels Surround Sound Channel ChartAdjusting Channel Levels on the FLY Adjusting the Tone ControlsControlling the T Using the HTR 2 Remote ControlSpecifications Learning Codes from Other RemotesPUNCH-THROUGH Copy a Command from Another KEYMacro Commands Recording MacrosDelete Mode KEY-ILLUMINATION TimeoutFactory Reset Loading CODE-LIBRARIESSummary of HTR 2 Modes Using the ZR 2 Remote ControlTrigger Setup Assigning the Trigger OutputTroubleshooting Condition Possible Causes Possible SolutionssAV Surround Sound Receiver SpecificationsPhysical Specifications Amplifier SectionNAD