NAD T 754 owner manual Digital Input Jack

Page 11

FRONT PANEL

11SOURCE : Use to select one of six inputs. Press repeatedly to step through the T 754’s audio/video inputs. The digital inputs are default assigned to the video input (DVD, SAT, VCR, VIDEO 4-5, CD) but can be arranged in any order using the T754’s SETUP OSD. The chart below shows the default assignments; see “Input Setup.”

Digital Input Jack

Default Assignment

OPT 1

DVD

OPT 2

SAT

Coax 3

VCR

Coax 4

VIDEO 4

Coax 5

VIDEO 5

Coax 6

CD

NOTE: Digital inputs take precedence: The T 754 will automatically play any active signal present at the selected digital input; if none is present, it will “fall back” to the analog audio input assigned to that Video input. Digital inputs can be selected OFF to listen to the analog input of a source with an assigned digital input.

12SURROUND MODE: Use to select the T 754’s Listening Mode. Press repeatedly to step through the T 754’s Listening Modes. See “About the T 754’s Listening Modes,” below.

NOTE: Depending on the format of the currently selected input (digital or analog; stereo or multichannel), different modes will be available. See “About the T 754’s Listening Modes,” below.

13LEVELS: Press repeatedly to select the channel, and then use the VOLUME(SETUP) knob to adjust the levels of the T 754’s 7 channels /pairs in turn: front-left, -center, –right; surround; surround back; subwoofer. The selected channel appears on the VFL and on-screen displays; use the VOLUME(SETUP) knob to adjust its level relative to the others over a range of ±12 dB. Channel levels may also be adjusted via the on-screen menus; see “Adjusting Channel Levels,” below.

NOTE: The HTR 2 remote’s [Surr.], [Center], and [Sub] / keys provide direct access to those channels’ relative levels, however in this case the level changes are only temporary and are not saved in memory.

14TONE DEFEAT: Press to disable the tone controls; press again to re-enable them for instance, to compare a tone setting to unmodified sound.

NOTE: While TONE DEFEAT is engaged, the TONE CONTROLS key will have no effect.

15TONE CONTROLS: Press to adjust treble using the VOLUME (SETUP) knob over a ±10 dB range; press again to adjust bass, and a third time to exit tone-control adjustment.

16SPEAKERS A & B: Press either speaker A or B or both to select the set of speakers you wish to listen to. The Speakers A are the main set of 6 multi- channel front and surround speakers. The Speaker B are an auxiliary set for remote locations such as other rooms of your home. For Speaker B selection all surround sound sources are downmixed to stereo as shown in the florescent display.

17VIDEO 6 INPUT: Use these convenience jacks for occasional sources, such as a camcorder, portable MP3 or tape player, or a video game console, or any other analog audio, or composite or S-Video video source. Select the Video 6 input using the HTR 2 remote, or the front-panel VIDEO 6 key.

18PHONES: Accepts stereo headphone using a standard 1/4-inch stereo phone plug (use a suitable adapter for headphones equipped with a smaller plug); set the Listening Mode to “Stereo.”

NOTE: For headphone listening the front left/right speakers must be set to “Large” on the OSD’s Speaker Settings page, otherwise headphone bass response will be restricted.

NOTE: Plugging in headphones will automatically switch the T 754 to “Stereo” mode.

ENGLISH

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 754 Explanation of Graphical Symbols Safety InformationDo not Attempt to Service the Unit Yourself OWNER’S Record Electric PowerMaintenance Damage Requiring ServiceTable of Contents Getting the Most from the NAD T Using the HTR 2 Remote ControlTroubleshooting Specifications Choosing a Location Unpacking and SetupConnecting AM Antenna WHAT’S in the BOXIntegration About the TR.S., Matrix and Digital Surround Ease of USEUpgradability About the HTR 2 System Remote ControlPlay a DVD Movie QuickstartSearch Front PanelDigital Input Jack +12V Trigger IN/OUT Rear PanelRear Panel Dealing with HUM and Noise Setting UP the TGetting Started Display the OSD Input SetupInput Settings About the ON-SCREEN Displays OSD and FRONT-PANEL ReadoutListening Mode Speaker SetupSpeaker Settings Setting Speaker Distance CHANNEL-BALANCE Test SetupUsing AN SPL Meter Setting Channel BalanceRecalling Presets Creating PresetsUsing the T Choosing the FM Mute / Mode Tuning StationsSetting Radio Presets Selecting Radio PresetsDTS NEO 6 Surround DTS ES Expanded Surround DTS ESDTS-ES Discrete DTS ES MatrixDolby PRO Logic II Music Dolby PRO LogicDolby PRO Logic II Surround Dolby PRO Logic II MovieDTS Displaying the Signal ModeSelecting Listening Modes DTS Neo Adjusting Listening ModesAdjusting the Tone Controls Surround Sound Channel ChartAdjusting Channel Levels on the FLY To Adjust Channel LevelsLearning Codes from Other Remotes Using the HTR 2 Remote ControlSpecifications Controlling the TRecording Macros Copy a Command from Another KEYMacro Commands PUNCH-THROUGHLoading CODE-LIBRARIES KEY-ILLUMINATION TimeoutFactory Reset Delete ModeAssigning the Trigger Output Using the ZR 2 Remote ControlTrigger Setup Summary of HTR 2 ModesCondition Possible Causes Possible Solutionss TroubleshootingAmplifier Section SpecificationsPhysical Specifications AV Surround Sound ReceiverNAD
Top Page Image Contents