Sharp AR-CF2 service manual Varoitus

Page 31

CAUTION FOR BATTERY REPLACEMENT

(Danish)ADVARSEL !

Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering.

Udskiftning må kun ske med batteri

af samme fabrikat og type.

Levér det brugte batteri tilbage til leverandoren.

(English)Caution !

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type

recommended by the manufacturer.

Dispose of used batteries according to manufacturer’s instructions.

(Finnish)

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti asennettu.

Vaihda paristo ainoastaan laitevalmistajan suosittelemaan

tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden

mukaisesti.

(French)ATTENTION

Il y a danger d’explosion s’ il y a remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du même type ou d’un type équivalent recommandé par

le constructeur.

Mettre au rebut les batteries usagées conformément aux

instructions du fabricant.

(Swedish)VARNING Explosionsfara vid felaktigt batteribyte.

Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion.

(German)Achtung

Explosionsgefahr bei Verwendung inkorrekter Batterien.

Als Ersatzbatterien dürfen nur Batterien vom gleichen Typ oder

vom Hersteller empfohlene Batterien verwendet werden. Entsorgung der gebrauchten Batterien nur nach den vom Hersteller angegebenen Anweisungen.

CAUTION FOR BATTERY DISPOSAL

(For USA, CANADA)

"BATTERY DISPOSAL"

THIS PRODUCT CONTAINS A LITHIUM PRIMARY

(MANGANESS DIOXIDE) MEMORY BACK-UP BATTERY THAT MUST BE DISPOSED OF PROPERLY. REMOVE THE BATTERY FROM THE PRODUCT AND CONTACT YOUR LOCAL ENVIRONMENTAL AGENCIES FOR INFORMATION ON RECYCLING AND DISPOSAL OPTIONS.

"TRAITEMENT DES PILES USAGÉES"

CE PRODUIT CONTIENT UNE PILE DE SAUVEGARDE DE MÉMOIRE LITHIUM PRIMAIRE (DIOXYDE DE MANGANÈSE) QUI DOIT ÊTRE TRAITÉE CORRECTEMENT. ENLEVEZ LA PILE DU PRODUIT ET PRENEZ CONTACT AVEC VOTRE AGENCE ENVIRONNEMENTALE LOCALE POUR DES INFORMATIONS SUR LES MÉTHODES DE RECYCLAGE ET DE TRAITEMENT.

Image 31
Contents Sharp Corporation Product Outline SpecificationsAR-CF2 External Views and Internal Structures 3 Sensors and switchesExternal Views and Internal Structures External componentsMotors, solenoid, and clutch Operational description Operational DescriptionStructure Function outlineNormal paper feed operation of inserter online/ offline Entering reverse section Reverse paper feeding operation of inserterExiting from reverse section Offline mode settingHow to set punching mode How to set stapling modeLED indication on operator panel Start LED Mode LEDLED LED1 LED2 LED3 LED4 List of Paper jams Paper jam/error detectionError detection Alarm detectionLED AdjustmentsPaper width detection level setting adjustment AR-CF2 Adjustments 5Pickup Roller & Paper Feed Roller Disassembly and AssemblyAR-CF2 Disassembly and Assembly 6 Paper Feed Separation UnitHorizontal Pass Roller 1 and Registration Roller Paper Feed UnitHorizontal Pass Roller 2 and Timing Roller Paper Guide Reverse Roller Belts Sensors Reverse flapper solenoid adjustmentDrive Unit Other PartsMaintenance list MaintenanceAR-CF2 Maintenance 7 AR-CF2 Troubleshooting 8 TroubleshootingPCB Tray alarm is displayed on the system display Electrical Section Actual Wiring ChartAR-CF2 Electrical DC+5V Block DiagramCircuit Description OutlineCommunication Circuit Circuit DetailSensor Input Circuits Paper Exit Sensor Hisen Paper Width Detection Potentiometer TVR Paper Feed Motor Drive Circuit Kmot Motor Drive CircuitsReset Circuit Eeprom Circuit Operator Panel Drive Circuit Inrush Current Limiting CircuitOperator Panel Circuit Memo Memo Example LEAD-FREE SolderVaroitus Trademark acknowledgements