NAD T762 Punch-Through, Copy a Command from Another KEY, Macro Commands, Recording Macros

Page 24

USING THE HTR 2 REMOTE CONTROL

 

PUNCH-THROUGH

 

The HTR 2’s “punch-through” function allows you to retain a function key from one Device Select “page”

 

on another, so that, for example, the AMP [SURR MODE] function might still control the T 762 when the DVD

 

Device Selector page is active

 

NOTE: The HTR 2’s [VOL] keys are pre-programmed as “punched-through” for all Device Select pages:

 

[VOL] will operate the T 762’s master-volume regardless of the currently selected device. The [SURR.]

 

[CENTER,] and [SUB] Channel Volume controls similarly are pre-programmed as punched-through.

 

To set a punch through, after entering the Learning Mode, and pressing the desired key to be punched-

 

through, simply press the device key twice of the device to punch through to. The status LED will turn green;

 

press the Device Selector key again to exit Learning Mode.

 

Example: Punch-through the from the DVD “page” to the AMP [SURR MODE] key:

 

• On the HTR 2, simultaneously press-and-hold [DVD] and [•] (record); the Learn LED turns steady green.

 

• Press [SURR MODE]; the Learn LED turns amber.

 

• Press [AMP] twice; the Learn LED turns green.

 

• Press [DVD] again to exit the learning mode.

 

COPY A COMMAND FROM ANOTHER KEY

 

You may copy a command from any HTR 2 key to any other. To copy a key function, after entering the

 

Learning Mode, and pressing the desired key to be copied to, simply press the device key from which you

 

wish to copy, having first pressed its Device Selector key if it resides on another “page.” The status LED will

 

turn green; press the Device Selector key again to exit Learning Mode.

 

Example: Copy the Pause command from the CD page to the AMP [ ] key:

 

• On the HTR 2, simultaneously press-and-hold [AMP] and [•] (record); the Learn LED turns steady green.

 

• Press [ ] (pause); the Learn LED turns amber.

 

• Press [CD]; press [ ] (pause); the Learn LED turns green.

 

• Press [AMP] again to exit the learning mode.

 

NOTE: The copy and punch-through functions are similar. However, if you copy a command and then

 

subsequently delete, or over-write the original (source-key) command , the copied-to key’s command

 

remains unchanged. If you punch-through to a command and then delete or over-write the original key,

 

the punched-through functions also change accordingly.

 

MACRO COMMANDS

 

A “macro” command is a series of two or more remote codes issued automatically from a single keypress.

 

You might use a macro to automate a simple command sequence, such as, “Turn on the DVD player and then

 

press ‘play.’” Or you might compose an elaborate macro to power up an entire system, select a source,

 

choose a Listening Mode, and begin playback—again, all from a single keypress. The HTR 2 can store one

 

macro on each of its function keys (these exclude the Device Selector keys).

 

NOTE: Macros are independent of the currently selected device.

 

RECORDING MACROS

 

To record a macro, simultaneously press-and-hold for 3 seconds both the [MACRO] key and the HTR 2

 

function key to which you wish to assign the macro, until the status LED turns green. The macro button will

 

also light up. Press the sequence of function keys to be recorded into the macro, being sure to first press

 

the requisite Device Selector key for each function (you may switch devices while recording the macro as

 

many times as necessary), allowing you to create macro containing commands from more than one Device

 

Selector “page.” When you have finished entering the desired command sequence, press [MACRO] again

 

to store the macro; the Learn LED and [MACRO] key illumination will turn off.

 

NOTE: Each macro can store a maximum of 64 command steps. If you exceed this number, the macro will

 

be stored automatically after the 64th command is added.

 

Example: Record a Macro to the [0] key to Turn on the T 762, Select the DVD Input, and Commence

 

Playback:

 

On the HTR 2, simultaneously press-and-hold [MACRO] and [0] (numeric zero); the Learn LED turns

 

 

steady green.

 

Press [AMP]; press [ON]; press [1] (red “DVD”); press [DVD]; press [play] (the Learn LED blinks as

 

 

each step is added).

 

Press [MACRO] again to exit the macro-record mode.

 

To clear a macro, perform the above steps without entering any functions.

 

EXECUTING MACROS

 

To execute a macro, press and release [MACRO]; its key illumination lights for 5 seconds. While it remains

 

lit, press an HTR 2 key to which a macro has previously been stored. The corresponding macro will run; as

 

each step executes, its “parent” Device Selector’s key flashes lights briefly; when execution is finished, the

 

[MACRO] key illumination goes out. Pressing any other HTR 2 key while a macro is executing will abort the

 

macro. Remember that you must hold the HTR 2 so that its infrared emitter can activate the target

 

components.

 

NOTE: When a macro executes, a 1 second delay is automatically inserted between its commands. If you

 

need more than a 1 second delay between particular commands—for example, to permit a component to

24

power up completely—you can record “empty” steps into the macro by changing Device Selector “pages”

without entering actual command functions.

 

Image 24
Contents English Safety Information Explanation of Graphical SymbolsPrecautions InstallationElectric Power MaintenanceDamage Requiring Service Do not Attempt to Service the Unit Yourself OWNER’S RecordTable of Contents Getting the Most from the NAD T Thank you for choosing NADUnpacking and Setup WHAT’S in the BOXChoosing a Location About the T R.S., Matrix and Digital SurroundEase of USE IntegrationAbout the HTR 2 System Remote Control UpgradabilityQuickstart Play a DVD MovieFront Panel Digital Input Jack Rear Panel 12V Trigger IN/OUT Setting UP the T Getting StartedDealing with HUM and Noise Input Setup About the ON-SCREEN Displays OSD and FRONT-PANEL ReadoutDisplay the OSD Navigating the OSD and Making ChangesSpeaker Setup Speaker SettingsListening Mode CHANNEL-BALANCE Test SetupCreating Presets Recalling PresetsMain/Zone DSP Decoding Dolby Digital Surround EX DecodingUsing the T Tuning Stations Setting Radio PresetsSelecting Radio Presets Choosing the FM Mute / ModeAbout the T 762S Listening Modes EarsDisplaying the Signal Mode Selecting Listening ModesDTS Adjusting Listening Modes Adjusting Channel Levels on the FLYAdjusting the Tone Controls Using the HTR 2 Remote Control SpecificationsControlling the T Learning Codes from Other RemotesCopy a Command from Another KEY Macro CommandsPUNCH-THROUGH Recording MacrosKEY-ILLUMINATION Timeout Factory ResetDelete Mode Loading CODE-LIBRARIESUsing the ZR 2 Remote Control Trigger SetupSummary of HTR 2 Modes Condition Possible Causes Possible Solutionss Specifications Physical SpecificationsAV Surround Sound Receiver Amplifier SectionNAD

T762 specifications

The NAD T762 is a powerful AV receiver that exemplifies NAD's commitment to high-quality audio and video performance. Designed for home theater enthusiasts, this receiver combines cutting-edge technologies with user-friendly operation, making it a popular choice among audiophiles and casual listeners alike.

One of the standout features of the NAD T762 is its robust amplification system. With a power rating of 60 watts per channel, the T762 can effortlessly drive a variety of speakers, delivering dynamic soundscapes whether you are watching movies, listening to music, or gaming. The receiver employs NAD's proprietary Soft Clipping technology, which allows it to produce clean audio even at higher volumes, minimizing distortion and providing a rich listening experience.

The T762 supports various surround sound formats, including Dolby Digital, DTS, and Pro Logic II, ensuring that users can enjoy an immersive sound environment. With its nine-channel output, the receiver can accommodate multi-room setups and advanced home theater configurations, giving users the flexibility to create their ideal audio landscape.

In terms of connectivity, the NAD T762 offers an extensive array of inputs and outputs, including HDMI, digital coaxial and optical inputs, and multiple analog connections. The inclusion of HDMI greatly enhances compatibility with modern video sources, allowing for high-definition video pass-through and audio return channel capabilities. Users can also benefit from the T762's integrated AM/FM tuner, providing access to a wide range of radio stations.

A key characteristic of the T762 is its easy-to-navigate user interface. The receiver is designed for straightforward setup and operation, with an intuitive on-screen display that guides users through the configuration process. The integrated remote control further simplifies usage, allowing quick access to the receiver's extensive features.

Additionally, the NAD T762 is constructed with high-quality components, ensuring durability and long-lasting performance. Its sleek design makes it an attractive addition to any home theater setup, blending seamlessly with other audio and video equipment.

In conclusion, the NAD T762 stands out as a high-performance AV receiver that offers a blend of power, versatility, and user-friendly operation. With its advanced amplification, support for multiple surround formats, and extensive connectivity options, it remains a solid choice for anyone serious about home audio and video entertainment.