Sharp XR-32X-L Regarding the Lamp Continued, Resetting the Lamp Timer, Info, Remove the lamp unit

Page 58

Regarding the Lamp (Continued)

Regarding the Lamp (Continued)

4 Remove the lamp unit.

•Loosen the securing screws from the lamp unit. Hold the lamp unit and pull it

in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it.

5 Insert the new lamp unit.
• Press the lamp unit firmly into the lamp
unit compartment. Fasten the securing	Securing screws
screws.

6 Replace the lamp unit cover.

•Align the tab on the lamp unit cover (1) and place it while pressing the tab

(2) to close it. Then tighten the user ser- vice screw (3) to secure the lamp unit cover.

Info

• If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is con- nected to the projector.

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.

Info

•Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or ex- plode.

1Connect the power cord.

•Plug the power cord into the AC socket of the projector.

2Reset the lamp timer.

•While simultaneously holding down MENU/HELP, ENTER and R on the pro- jector, press STANDBY/ON on the pro- jector.

•“LAMP 0000H” is displayed, indicating that the lamp timer is reset.

AC socket

STANDBY/ON button

ENTER button

R button

MENU/HELP button

54

Image 58

Contents XR-32X-L XR-32S-L SetupFeatures OPERATION MANUALModel No Serial No SPECIAL NOTE FOR USERS IN THE U.K DANGERThe supplied CD-ROM contains operation instructions in English, German, French, Spanish, Italian, Dutch, Swedish, Portuguese, Chinese, Korean and Arabic. Carefully read through the operation instructions before operating the projector Introduction 1. WARRANTY2. CONSUMER PRODUCT SAFETY ACT IntroductionENGLISHDeclaration of conformity Caution Concerning Lamp ReplacementINFORMATION PRODUCT DISPOSALFor Future Reference MaintenanceTroubleshooting IndexSetup ContentsUsing Useful FeaturesReference Appendix8. Accessories IMPORTANT SAFEGUARDS5. Cleaning 11. Power Sources20. Safety Check 18. Damage Requiring Service19. Replacement Parts 15. OverloadingCaution concerning the lamp unit Observe the following safeguards when setting up your projectorCaution concerning the setup of the projector Warning about placing the projector in a high positionUsing the projector in other countries How to Access the PDF Operation ManualsInfo Accessing the PDF Manuals for Windows For Macintosh, skip stepSupplied accessories AccessoriesOptional accessories Introduction Part Names and FunctionsProjector Top ViewUsing the Kensington Lock Part Names and Functions ContinuedRear View TerminalsFor the Left click For selecting and adjusting menu itemsFor moving the For changing the pointer or spotInserting the Batteries 2 Insert the batteriesUsable Range 1. Place the projector facing a wall or a screen Setup and ProjectionQuick Start 3. Remove the lens cap and turn the projector on5. Correct trapezoidal distortion 4. Adjust the projected image with the Setup Guide7. Turn the computer on 8. Turn the power off 6. Select the INPUT modeStandard Setup Front Projection Setting up the ProjectorSetting up the Projector Ceiling-mount SetupProjection PRJ Mode SetupIndication of the Projection Image Size and Projection Distance NORMAL Mode Setting up the Projector ContinuedScreen Size and Projection Distance STRETCH ModeConnections Connecting the Projector to Other EquipmentTerminals on the Projector Example Terminals of XR-32XConnecting the Projector to Other Equipment Continued Connections Plug the supplied power cord into the Connecting the Power CordControlling the Projector by a Computer AC socket on the rear of the projector Then plug into AC outletOperationBasic Turning the Projector On/OffTurning the Projector on Turning the Power off Putting the Projector into Standby Mode2 Adjusting the Picture Size About the Setup GuideAdjusting the Projected Image 1 Adjusting the Focus Image Projection3 Adjusting the Height 2 Press P/Q or O/R to adjust the Keystone Correction Image Projection ContinuedCorrecting Trapezoidal Distortion 1 Press KEYSTONE to enter the Keystone Correction modeDisplaying the Black Screen and Turning off the Sound Temporarily Switching the Input ModeAdjusting the Volume Press VOL +/- on the remote control orCOMPUTER Resize ModePress RESIZE About Copyrights VIDEO/DTVUsing the Spot Function Operating with the Remote ControlDisplaying and Setting the Break Timer Switching the Eco+Quiet ModeSelecting the Picture Mode Auto Sync Auto Sync AdjustmentFreezing a Moving Image Displaying an Enlarged Portion of an ImageUsing the Remote Control as the Wireless Computer Mouse Operating with the Remote Control ContinuedConnecting with a USB cable “Picture” menu Menu ItemsThe following shows the items that can be set in the projector “C.M.S.”“Screen adjustment SCR-ADJ” menu Menu Items Continued“Projector adjustment PRJ-ADJ” menu The items you can set with the “Help” menu “Help” menu2 Press Q or O and select “Picture” to adjust Using the Menu ScreenMenu Selections Adjustments 1 Press MENU/HELP4 Press O or Q to adjust the item selected To adjust the projected image while watching it3 Press P or R and select “Bright” to adjust Press ENTERPicture Adjustment “Picture” Menu 1 Selecting the Picture Mode4Adjusting the Colors 2Adjusting the Image3Adjusting the Color Temperature ENTER5 Progressive Picture Adjustment “Picture” Menu Continued7Lamp Setting 6 Reducing Image Noise DNR2 Adjusting the Image Position Adjusting the Projected Image “SCR - ADJ” Menu1 Setting the Resize Mode 4 Setting the On-screen Display5 Selecting the Background Image Adjusting the Projected Image “SCR - ADJ” Menu Continued6 Selecting the Setup Guide 7 Reversing/Inverting Projected Images2 Auto Power Off Function Adjusting the Projector Function “PRJ - ADJ” MenuAdjustment 5 Setting the Confirmation7 Audio Input XR-32X only 9 Fan Mode Settinga Setting/Changing the keycode 0 System Lock FunctionLocking the Operation Buttons on the Projector Keylock FunctionChecking the Lamp Life Status 5 Enter the same keycode in “Re- confirm”6 Press O or Q to adjust Troubleshooting with the “Help” MenuUtilizing the “Help” Menu Functions 2 Press Oor Qto select “Help”, then press ENTERCleaning the projector MaintenanceAppendix Cleaning the lensAbout the temperature warning indicator Maintenance IndicatorsAbout the lamp indicator If the temperature warning indicator illuminates, and the projector enters standby mode, follow the possible solutions above and then wait until the projector has cooled down completely before plug- ging in the power cord and turning the power back on. At least 10 minutes Hg LAMP CONTAINS MERCURY For State Lamp Disposal Regarding the LampLamp Information3 Remove the lamp unit cover Removing and Installing the Lamp Unit2 Disconnect the power cord Lamp unit1 Connect the power cord Resetting the Lamp TimerRegarding the Lamp Continued 2 Reset the lamp timersub 15 pin female connector Connecting Pin AssignmentsDVI-D Terminal 24 pin connector XR-32X only Connecting Pin Assignments Continued RS-232C Cable recommended connection D-sub 9 pin female connectorCommunication conditions RS-232C Specifications and CommandsComputer control Basic formatExample When turning on the projector, make the following setting RS-232C Specifications and Commands ContinuedCommands P O W RAppendix RS-232C Specifications and Commands Continued is only for XR-32XAppendix Computer Compatibility Chart ComputerTroubleshooting 21-24using STANDBY/ON on Troubleshooting Continued49, 50 For SHARP Assistance Specifications Dimensions Units inches mm33, 37, 45 IndexCOMPUTER/COMPONENT input terminal

Related manuals

Manual 73 pages 59.7 Kb