Sharp XR-32X quick start Upper side, Control

Page 21

4.Adjust the projected image with the Setup Guide

1After the projector turns on, the Setup Guide appears. (When ÒSetup GuideÓ is set to ÒOnÓ. See page 44.)

2Follow the steps in the Setup Guide and adjust the focus, picture size, and height (angle).

3After adjusting the focus, height (angle) and picture size, press ENTER to finish the Setup Guide.

_PP. 26, 27

5. Correct trapezoidal distortion

Correcting trapezoidal distortion using Keystone Correction.

On the projector

Shrinks	Shrinks
upper side.	lower side.

On the remote control

_P. 28

6. Select the INPUT mode

Select the ÒCOMPUTERÓ using INPUT on the projector or COMPUTER on the remote control.

On the			On the remote	INPUT list			On-screen display (RGB)
projector			control
					INPUT
									COMPUTER
									COMPUTER
					COMPUTER				RGB
					COMPUTER				RGB
						*			1024 ⋅ 768
						*

DDVI-D Computer

DDVI-D Video

*XR-32X only

•When you press INPUT on the projector, the INPUT list appears. Press '/" to switch the INPUT mode.

_P. 29

7.Turn the computer on

8.Turn the power off

Press STANDBY/ON on the projector or STANDBY on the remote control, and then press the button again while the confirmation message is displayed to put the projector into standby mode.

On the	On-screen display
On the	On the remote
projector	control

_P. 25

Quick Start

17

Image 21

Contents XR-32X XR-32X XR-32SModel No Serial No If YOU have ANY DOUBT, Consult a Qualified Electrician This Apparatus Must be EarthedPage A. only IntroductionENGLISHSharp PROJECTOR, Model XR-32X/XR-32S Sharp Electronics CorporationOnly For Future Reference Using the Menu ScreenContents Reference Accessories CleaningPower Sources Power-Cord ProtectionReplacement Parts Damage Requiring ServiceSafety Check OverloadingRest your eyes occasionally Avoid locations with extremes of temperatureDo not block the exhaust and intake vents See ÒReplacing the LampÓ onTemperature monitor function Using the projector in other countriesIf the projector starts to overheat due to setup Other connected equipmentOptional accessories AccessoriesProjector Part Names and FunctionsAudio 1 input terminal Rear ViewComputer Audio OUTUP/PAGE COMPUTER, *DVICLICK/EFFECT CLICK/RETURNInserting the Batteries Usable Range Setup and Projection Quick StartHeight Control Upper sideSetting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount SetupExample Normal Mode Picture Size Projection PRJ Mode120 Projection DistanceNormal Mode Stretch ModeScreen Size and Projection Distance You may need other cables or connectors not listed below Connecting the Projector to Other EquipmentExample Terminals of XR-32X Is only for XR-32XConnecting the Projector to Other Equipment Audio XR-32S Connecting the Power Cord AC socket To AC outlet Power cord suppliedControlling the Projector by a Computer Turning the Projector On/Off Lamp indicator Power indicator STANDBY/ON buttonTurning the Projector on On-screen display confirmation messageAdjusting the Projected Image Adjusting the Focus About the Setup GuideAdjusting the Picture Size Image ProjectionUse the rear adjustment foot to make the projector level Adjusting the HeightPress P/Q or O/R to adjust Keystone Correction Press Keystone to enter the Keystone Correction modeCorrecting Trapezoidal Distortion Shrinks upper side Move the slide bar in the + directionSwitching the Input Mode Adjusting the VolumeOn-screen display Resize Mode Press ResizeResize About Copyrights Displaying and Setting the Break Timer Operating with the Remote ControlUsing the Spot Function Switching the Eco+Quiet ModeSelecting the Picture Mode Auto Sync Auto Sync AdjustmentFreezing a Moving Image Displaying an Enlarged Portion of an ImageWhen moving the cursor Using the Remote Control as the Wireless Computer MouseWhen left-clicking When right-clickingFollowing shows the items that can be set in the projector Menu ItemsScreen adjustment SCR-ADJ menu ÒHelpÓ menu n Items you can set with the Help menuMenu Selections Adjustments Using the Menu ScreenPress Qor Oand select Picture to adjust Example Adjusting ÒBrightÓPress P or R and select Bright to adjust To adjust the projected image while watching itPress O or Q to adjust the item selected Press Enter1Selecting the Picture Mode Picture Adjustment Picture MenuMenu operation n PAGE1 PAGE24Adjusting the Colors 2Adjusting the Image3Adjusting the Color Temperature Adjusting ÒHueÓ, ÒSaturationÓ, or ÒValueÓ7Lamp Setting ProgressiveReducing Image Noise DNR 1Setting the Resize Mode Adjusting the Projected Image SCR ADJ Menu2Adjusting the Image Position 3Keystone Correction 4Setting the On-screen Display5Closed Caption 7Selecting the Setup Guide6Selecting the Background Image Reversing/Inverting Projected Images2Auto Power Off Function 1Auto Sync Auto Sync Adjustment4STANDBY Mode 5Setting the Confirmation Sound System Sound7Audio Input XR-32X only 9Fan Mode Setting0System Lock Function Select System Lock, then press Enter or QChecking the Lamp Life Status Keylock FunctionEnter the same keycode in Re- confirm Locking the Operation ButtonsTroubleshooting with the Help Menu Enter button Adjustment buttons P/R/O/Q MENU/HELP buttonUtilizing the Help Menu Functions Cleaning the projector MaintenanceTemperature warning indicator Lamp indicator Power indicator Maintenance IndicatorsPlease exercise care when Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Disconnect the power cordRemove the lamp unit cover Resetting the Lamp Timer Connecting Pin Assignments Sub 15 pin female connectorDVI-D Terminal 24 pin connector XR-32X only USB Terminal Type B USB connector RS-232C Terminal mini DIN 9 pin female connectorComputer control RS-232C Specifications and CommandsCommunication conditions Basic formatCommands RS-232C Specifications and CommandsERR DNR Video Input Picture Mode Standard OK or ERR PAL Computer Computer Compatibility Chart21-24 Troubleshooting49, 50 For Sharp Assistance Specifications Dimensions Index