Sharp XR-32X quick start Regarding the Lamp, Replacing the Lamp

Page 56

Regarding the Lamp

Lamp

■It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes 5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. (See page 47.)

■Purchase a replacement lamp of type AN-F212LP from your place of purchase, nearest Sharp Authorized Projector Dealer or Service Center.

IMPORTANT NOTE TO U.S. CUSTOMERS:

The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this projector under warranty, including lamp replacement, must be obtained through a Sharp Authorized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).

Hg LAMP CONTAINS MERCURY For State Lamp Disposal

Information

 

www.lamprecycle.org or 1-800-BE-SHARP

U.S.A. ONLY

Caution Concerning the Lamp

■This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time.

The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking.

■When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally.

■Should the lamp break, there is also a possibility that glass particles may spread inside of the projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or Service Center to assure safe operation.

■Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible.

Replacing the Lamp

Caution

•Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burns or injury.

•Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before removing the lamp unit.

■Carefully change the lamp by following the instructions described in this section. * If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center.

*If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized Projector Dealer or Service Center for repair.

52

Page 55 Page 57
Image 56
Page 55 Page 57
Contents XR-32X XR-32S XR-32XModel No Serial No This Apparatus Must be Earthed If YOU have ANY DOUBT, Consult a Qualified ElectricianPage IntroductionENGLISH A. onlyOnly Sharp PROJECTOR, Model XR-32X/XR-32SSharp Electronics Corporation Using the Menu Screen For Future ReferenceContents Reference Cleaning AccessoriesPower Sources Power-Cord ProtectionDamage Requiring Service Replacement PartsSafety Check OverloadingAvoid locations with extremes of temperature Rest your eyes occasionallyDo not block the exhaust and intake vents See ÒReplacing the LampÓ onUsing the projector in other countries Temperature monitor functionIf the projector starts to overheat due to setup Other connected equipmentAccessories Optional accessoriesPart Names and Functions ProjectorRear View Audio 1 input terminalComputer Audio OUTCOMPUTER, *DVI UP/PAGECLICK/EFFECT CLICK/RETURNInserting the Batteries Usable Range Height Setup and ProjectionQuick Start Upper side ControlSetting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount SetupProjection PRJ Mode Example Normal Mode Picture Size120 Projection DistanceScreen Size and Projection Distance Normal ModeStretch Mode Connecting the Projector to Other Equipment You may need other cables or connectors not listed belowExample Terminals of XR-32X Is only for XR-32XConnecting the Projector to Other Equipment Audio XR-32S Controlling the Projector by a Computer Connecting the Power CordAC socket To AC outlet Power cord supplied Lamp indicator Power indicator STANDBY/ON button Turning the Projector On/OffTurning the Projector on On-screen display confirmation messageAbout the Setup Guide Adjusting the Projected Image Adjusting the FocusAdjusting the Picture Size Image ProjectionAdjusting the Height Use the rear adjustment foot to make the projector levelPress Keystone to enter the Keystone Correction mode Press P/Q or O/R to adjust Keystone CorrectionCorrecting Trapezoidal Distortion Shrinks upper side Move the slide bar in the + directionOn-screen display Switching the Input ModeAdjusting the Volume Resize Resize ModePress Resize About Copyrights Operating with the Remote Control Displaying and Setting the Break TimerUsing the Spot Function Switching the Eco+Quiet ModeAuto Sync Auto Sync Adjustment Selecting the Picture ModeFreezing a Moving Image Displaying an Enlarged Portion of an ImageUsing the Remote Control as the Wireless Computer Mouse When moving the cursorWhen left-clicking When right-clickingMenu Items Following shows the items that can be set in the projectorScreen adjustment SCR-ADJ menu Items you can set with the Help menu ÒHelpÓ menu nUsing the Menu Screen Menu Selections AdjustmentsPress Qor Oand select Picture to adjust Example Adjusting ÒBrightÓTo adjust the projected image while watching it Press P or R and select Bright to adjustPress O or Q to adjust the item selected Press EnterPicture Adjustment Picture Menu 1Selecting the Picture ModeMenu operation n PAGE1 PAGE22Adjusting the Image 4Adjusting the Colors3Adjusting the Color Temperature Adjusting ÒHueÓ, ÒSaturationÓ, or ÒValueÓReducing Image Noise DNR 7Lamp SettingProgressive Adjusting the Projected Image SCR ADJ Menu 1Setting the Resize Mode2Adjusting the Image Position 3Keystone Correction 4Setting the On-screen Display7Selecting the Setup Guide 5Closed Caption6Selecting the Background Image Reversing/Inverting Projected Images1Auto Sync Auto Sync Adjustment 2Auto Power Off Function4STANDBY Mode 5Setting the Confirmation Sound System Sound9Fan Mode Setting 7Audio Input XR-32X only0System Lock Function Select System Lock, then press Enter or QKeylock Function Checking the Lamp Life StatusEnter the same keycode in Re- confirm Locking the Operation ButtonsUtilizing the Help Menu Functions Troubleshooting with the Help MenuEnter button Adjustment buttons P/R/O/Q MENU/HELP button Maintenance Cleaning the projectorMaintenance Indicators Temperature warning indicator Lamp indicator Power indicatorPlease exercise care when Replacing the Lamp Regarding the LampLamp Remove the lamp unit cover Removing and Installing the Lamp UnitDisconnect the power cord Resetting the Lamp Timer DVI-D Terminal 24 pin connector XR-32X only Connecting Pin AssignmentsSub 15 pin female connector RS-232C Terminal mini DIN 9 pin female connector USB Terminal Type B USB connectorRS-232C Specifications and Commands Computer controlCommunication conditions Basic formatRS-232C Specifications and Commands CommandsERR DNR Video Input Picture Mode Standard OK or ERR PAL Computer Compatibility Chart ComputerTroubleshooting 21-2449, 50 For Sharp Assistance Specifications Dimensions Index
Top Page Image Contents