Runco VX-55D External Control, Serial Communications, RS-232 Connection, Port Configuration

Page 103

6. External Control

In addition to using the DHD Controller front-panel keypad or remote control unit, there are two methods of controlling the VX-44d/-55d and DHD Controller externally:

Using a serial (RS-232) link to send ASCII commands and receive responses to those commands.

Using discrete infrared (IR) codes to program a third-party remote control unit.

The following sections describe both of these methods.

The DHD Controller uses a simple text-based control protocol to take requests from control devices and to provide responses to such devices. This section describes how to send control messages over a serial link between the DHD Controller and an automation/control system or a PC running terminal emulation software.

6.1

Serial Communications

To interface the DHD Controller with an automation/control system or a PC running

RS-232 Connection and

terminal emulation software, connect it to your control system or PC as shown in Figure

Port Configuration

3-15.

 

Configure the RS-232 controller or PC serial port as follows: no parity, 8 data bits, 1 stop

 

bit and no flow control. Set the baud rate to 19200, to match that of the DHD Controller

 

RS-232 port.

 

Serial commands to the DHD Controller take the following form:

Serial Command Syntax

Commands are not case-sensitive.

For a single command that takes no parameters, type the command followed by a carriage return; for example, to set the aspect ratio to Letterbox, type

LETTERBOX <Enter>.

For a single command that takes a parameter, type the command, a space or a comma and the desired value followed by a carriage return; for example, to set the brightness to -10, type BRIGHTNESS -10<Enter> or

BRIGHTNESS,-10 <Enter>.

You can also send a string of multiple commands on a single line, separated by commas. For example, COMPOSITE,BRIGHTNESS 50,16:9 <Enter> switches to the Composite video input, sets the brightness to 50 and sets the aspect ratio to 16:9. Command strings can be up to 255 characters long.

Avoid combining the ON or POWER 1 commands with other commands Note on a single line. After sending ON or POWER 1, allow at least five (5)

seconds for the DHD Controller to power up. If you have enabled the ISF splash screen (refer to Splash Configure on page 70), allow 15

seconds for the DHD Controller to power up.

Once it does, it will accept and properly execute multiple serial commands.

Runco VX-44d/-55d Installation/Operation Manual

87

Image 103
Contents VX-44d VX-55d Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Install Projector Stand CineWide with AutoScope, Floor-Mount External Control Maintenance and TroubleshootingSpecifications OperationTable of Contents Xiv List of Figures Xvi About This Manual IntroductionDegrade performance or cause a malfunction Using This ManualCertain features Significance. They also provide supplemental informationFormat screen Description, Features and BenefitsOptional Accessories VX-44d/-55d at a Glance Controls and FunctionsVX-44d/-55d Input Panel Ethernet RemoteInput 1 Rgbhv VX-44d/-55d Built-In Keypad Right Button UP ButtonLeft Button Down ButtonVacuum Fluorescent Display DHD Controller Front PanelRunco Icon IR SensorStandby LED Menu ButtonTriggers DHD Controller Rear PanelOutputs 1. Hdmi Out Display ControlInputs Main Power SwitchMain AC Fuse DHD Controller/VX-44d/-55d Remote Control VX-44d/-55d Remote Control UnitLight IR Output IndicatorEnter Return / ExitCust CinemaISF Night ISF DAYRemote Control InstallationInstallation specialist Quick SetupInstallation Overview Installation must be performed by a qualified custom videoAmbient Light Installation ConsiderationsProjector Installation Options Installation TypeVX-44d/-55d Lens Options and Throw Ratios Position Ceiling InstallationFloor Installation Vertical and HorizontalHorizontal Lens Shift Example only Vertical and Horizontal Lens Shift Limits Input Timing Possible Audio Latency milliseconds Synchronization IssuesPossible Audio Latency for Various Input/Output Timings Audio/VideoOther Considerations Installing the Projection LensAutoScope or Base Plate Installing the Optional CineWide Lens MountFixed CineWide Are both fully assembled AutoScope stand used for floor-mounted projector VX-44d/-55d MountingVX-44d/VX-55d Input Panel Connections to VX-44d/-55d and DHD ControllerController Connecting SourceComponents to the DHD Sections that follow10. Hdmi Source Connections DTV-Set-Top Box BD/DVD DTV-STB12. Rgbhv Source Connections Computer RGB CamcorderDVD/DTV STB VCRGaming Console Camcorder Composite and S-Video Source ConnectionsConnection RS-232 ControllerAutoScope Lens Motor Connecting 12-volt Trigger Outputs to External EquipmentReceiver to the DHD Connecting an External IRInput voltage to the AutoScope lens motor must be between Connecting to AC PowerHdmi Turning on the PowerFocus and Zoom Vertical and Horizontal Lens Shift Primary Lens AdjustmentsAdjusting the Picture Orientation On the VX-44d/-55d built-in keypad see -3, press MenuWith AutoScope or Base Installing and Adjusting the CineWide Anamorphic LensAssembly to Lens Motor Carriage Plate CineWideHorizontal Position X Adjustment Installation Geometry Anamorphic Lens Top ViewNavigating the Projector Menus Installation Lamp AdjustAre disabled Optimizing Lamp and Lens PerformanceInstallation Menu To using LumaCalLumaCal lamp calibration takes approximately two minutes Above, the Automatic Lens Calibration setting has no effect Power cyclesMore information, refer to RVR on Filter Replacement onWorking With the Lamp More information, refer to Lamp onIntensity value is not the actual lumen output, but rather a Originally expected may no longer be possibleMore easily maintained as the lamp ages Installation Operation Using the On-Screen MenusMain Menu ServiceRunco Video Aspect Ratio Input SourceAspect Ratio Input SourceHdtv programs in their Aspect Ratio SettingsRemote Aspect Ratio Control Description Key 169 Select 169 to view 169 DVDsOverscan Remote Aspect Ratio Control Description KeyPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input Position ResolutionInput Position Adjust the Phase after adjusting Tracking see below Memory Presets Memory PresetsInformation You must enter a passcode to access the Calibration menuCalibration Operation Color Temperature Preset Associated x/y Values Color Temperature Presets and Associated Color PointsDisplay Color Auto Color Enable Test Pattern Enable Description SettingCopy/Paste Copied settings are not retained after a power cycleShould be used by ISF-certified technicians only ServiceYou must enter a passcode to access the Service menu ServiceInput Names Absolutely necessary, as it may cause artifacts in the image Operation Operation Operation 64 and ISF Day/Night Memory Presets Lamp and Filter Replacement Maintenance and TroubleshootingLamp Replacement Removing the Lamp Lens Replacement Removing the Primary Lens Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Configure Lens Motor Lamp Failures VX-44d/-55d Error CodesError Codes Code Description GeneralTipm Image Processor Code Description Power and CoolingBuilt-In Keypad Miscellaneous Code Description Panel Driver and FormatterMaintenance and Troubleshooting Serial Communications Port ConfigurationSerial Command Syntax External ControlInput Selection Commands Serial CommandsAspect Ratio Commands Image Preset Commands Output Shift Commands Exit Return key Enter keyCommand Bits Using Discrete IR CodesWith Toggle Bit = Hex Binary Function Start RC5 Data IR Command ListRemote Control With Toggle Description Button Name Bit = RC5 Control Codes for the DHD ControllerEnter VX-44d/-55d Specifications SpecificationsVX-44d/-55d Specifications Dimensions Theater Calibration SpecificationsIndustry-Standard Specifications Power Requirements VX-44dDHD Controller Specifications DHD Controller SpecificationsVX-44d/-55d Dimensions VX-44d/-55d DimensionsSupported? √ = Yes, = No Supported Signal Timings by InputFormat Resolution Frequency Rate Hz MHz KHz Supported TimingsPAL-B/G/H/I 101 102 Page 020-0826-02 Rev. B April
Related manuals
Manual 114 pages 2.55 Kb

VX-55D, VX-44D specifications

The Runco VX-55D and VX-44D projectors represent a pinnacle in home theater technology, offering expansive image quality and immersive viewing experiences. Runco, known for its commitment to delivering exceptional visual performance, has integrated numerous features and advanced technologies in these models.

One of the standout features of both the VX-55D and VX-44D is their native 1080p resolution, delivering stunningly sharp images with vibrant colors that capture the finest details. This high definition capability ensures that viewers can enjoy their favorite movies, sports, and gaming content with unparalleled clarity. The projectors utilize the latest DLP (Digital Light Processing) technology, which enhances brightness and color accuracy, providing a more vivid and lifelike picture.

Another impressive characteristic of the Runco VX series is its exceptional contrast ratios. With deep blacks and brilliant whites, these projectors offer a dynamic range that brings out subtle details in both shadow and highlight areas. This contrast performance is particularly beneficial for watching films in darker environments, where the depth of imagery is crucial for immersion.

In terms of color processing, the VX-55D and VX-44D incorporate Runco's proprietary ColorPalette technology. This system ensures accurate and rich color reproduction by utilizing a wide color gamut, allowing viewers to experience content as the creators intended. Coupled with advanced color management capabilities, users can further tweak their viewing experience to match their preferences.

The integration of flexible installation options is another highlight of these projectors. They support up to 10-point digital keystone correction, making setup simple and adaptable to various room configurations. This flexibility ensures that no matter the space, users can achieve a perfectly aligned and geometrically accurate image.

Runco has also designed the VX-55D and VX-44D with user-friendly interfaces, including intuitive remote controls and on-screen menus. Both projectors come equipped with multiple HDMI inputs, allowing users to connect various devices seamlessly. Additionally, they support 3D content playback, a feature that has become increasingly important for enhancing the cinematic experience.

Energy efficiency is a consideration in the design of these projectors as well, making them not only high-performance devices but also more sustainable than many of their counterparts. With a sleek aesthetic, the Runco VX-55D and VX-44D can seamlessly blend into any home theater setup, adding a touch of elegance while providing an extraordinary viewing experience.

In summary, the Runco VX-55D and VX-44D projectors are characterized by their high-definition resolution, advanced DLP technology, rich color processing, and flexible installation options, making them ideal choices for any home theater enthusiast looking to elevate their viewing experience.