Runco VX-55D, VX-44D Copied settings are not retained after a power cycle, Copy/Paste

Page 85

Input Image: The Input Image controls are functionally similar to those in the Picture menu (refer to page 58), but are accessible only by entering the Calibration menu passcode.

The Input Image settings establish the “zero point” for the Picture

Note menu settings, whose values represent offsets from the Input Image settings. For example, if you set Brightness to 10 in this menu, setting Brightness to 10 in the Picture menu results in an actual setting value of 20 (10+10).

Input Color: The Input Color controls are similar to those in the Display Color menu (see above), but adjust the color balance of the incoming signal. These settings are also saved independently for each input and display mode.

•Gain/Offset (HD1, HD2 and Component/SCART inputs only): These controls operate similarly to those in the Display Color menu (described on page 65), but affect the Y, Pb and Pr signal components rather than the red, green and blue channels.

•Chroma Delay: use the Chroma Delay control to correct a mis-aligned image from a Composite or S-Video source. Chroma delay in an image causes color shifts to occur to the left of the vertical edge transitions, producing artificial shadows or a “halo” effect. If necessary, adjust this setting to eliminate them.

•Noise Filter: To apply noise filtering to the input signal, select Noise Filter from the Input Color menu. The Noise Filter is useful for clearing up noisy images from 480i video sources.

Use the left- or right-arrow buttons to select the desired amount of noise reduction, keeping in mind that higher settings (which reduce high frequencies) may also “soften” the image.

Save ISF Night/Save ISF Day: Whenever you make a change to the ISF settings, you should always save it. Select Save ISF Night or Save ISF Day from the Calibration menu to do this.

Copy/Paste: You can copy and paste settings from one memory location to another. This gives you a convenient starting point for creating a new preset based on an existing one, to make the calibration process less time-consuming.

For example, you can use the Copy/Paste feature to:

•Apply settings from HDMI 1 to HDMI 2, or from HD1 to HD2.

•Calibrate an input for 720p source signals, then use those settings for 1080i sources.

•Duplicate ISF Night settings for a given source and signal format and save them in the “Custom” memory preset.

To use this feature, select Copy/Paste from the Calibration menu.

•Copy Settings: Select Copy Settings from the Copy/Paste menu to place the settings for the current input source, signal format (resolution and frame rate) and memory preset onto a “clipboard,” which is a temporary memory location. When you do, the message “Settings Copied” briefly appears on-screen. The Copy/Paste menu then re-appears, indicating the source of the copied settings.

Copied settings are not retained after a power cycle.

Note

Copy/Paste

Copy Settings

Paste Settings

Copied From:

 

Input Source

HDMI 1

Signal Format

1080p/60

Memory Preset

ISF Night

Runco VX-44d/-55d Installation/Operation Manual

69

Page 84 Page 86
Image 85
Page 84 Page 86
Contents VX-44d VX-55d Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Install Projector Stand CineWide with AutoScope, Floor-Mount Specifications Maintenance and TroubleshootingOperation External ControlTable of Contents Xiv List of Figures Xvi About This Manual IntroductionCertain features Using This ManualSignificance. They also provide supplemental information Degrade performance or cause a malfunctionFormat screen Description, Features and BenefitsOptional Accessories VX-44d/-55d at a Glance Controls and FunctionsVX-44d/-55d Input Panel Ethernet RemoteInput 1 Rgbhv VX-44d/-55d Built-In Keypad Left Button UP ButtonDown Button Right ButtonRunco Icon DHD Controller Front PanelIR Sensor Vacuum Fluorescent DisplayStandby LED Menu ButtonOutputs 1. Hdmi Out DHD Controller Rear PanelDisplay Control TriggersInputs Main Power SwitchMain AC Fuse DHD Controller/VX-44d/-55d Remote Control VX-44d/-55d Remote Control UnitEnter IR Output IndicatorReturn / Exit LightISF Night CinemaISF DAY CustRemote Control InstallationInstallation Overview Quick SetupInstallation must be performed by a qualified custom video Installation specialistProjector Installation Options Installation ConsiderationsInstallation Type Ambient LightVX-44d/-55d Lens Options and Throw Ratios Floor Installation Ceiling InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Vertical and Horizontal Lens Shift Limits Possible Audio Latency for Various Input/Output Timings Synchronization IssuesAudio/Video Input Timing Possible Audio Latency millisecondsOther Considerations Installing the Projection LensAutoScope or Base Plate Installing the Optional CineWide Lens MountFixed CineWide Are both fully assembled AutoScope stand used for floor-mounted projector VX-44d/-55d MountingVX-44d/VX-55d Input Panel Connections to VX-44d/-55d and DHD ControllerComponents to the DHD Connecting SourceSections that follow Controller10. Hdmi Source Connections DTV-Set-Top Box BD/DVD DTV-STB12. Rgbhv Source Connections Computer RGB CamcorderDVD/DTV STB VCRGaming Console Camcorder Composite and S-Video Source ConnectionsConnection RS-232 ControllerAutoScope Lens Motor Connecting 12-volt Trigger Outputs to External EquipmentReceiver to the DHD Connecting an External IRInput voltage to the AutoScope lens motor must be between Connecting to AC PowerHdmi Turning on the PowerAdjusting the Picture Orientation Primary Lens AdjustmentsOn the VX-44d/-55d built-in keypad see -3, press Menu Focus and Zoom Vertical and Horizontal Lens ShiftAssembly to Lens Motor Installing and Adjusting the CineWide Anamorphic LensCarriage Plate CineWide With AutoScope or BaseHorizontal Position X Adjustment Installation Geometry Anamorphic Lens Top ViewAre disabled Installation Lamp AdjustOptimizing Lamp and Lens Performance Navigating the Projector MenusInstallation Menu To using LumaCalLumaCal lamp calibration takes approximately two minutes Above, the Automatic Lens Calibration setting has no effect Power cyclesWorking With the Lamp Filter Replacement onMore information, refer to Lamp on More information, refer to RVR onIntensity value is not the actual lumen output, but rather a Originally expected may no longer be possibleMore easily maintained as the lamp ages Installation Operation Using the On-Screen MenusMain Menu ServiceRunco Video Aspect Ratio Input SourceInput Source Aspect RatioRemote Aspect Ratio Control Description Key 169 Aspect Ratio SettingsSelect 169 to view 169 DVDs Hdtv programs in theirOverscan Remote Aspect Ratio Control Description KeyPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input Position ResolutionInput Position Adjust the Phase after adjusting Tracking see below Memory Presets Memory PresetsInformation You must enter a passcode to access the Calibration menuCalibration Operation Color Temperature Preset Associated x/y Values Color Temperature Presets and Associated Color PointsDisplay Color Auto Color Enable Test Pattern Enable Description SettingCopy/Paste Copied settings are not retained after a power cycleYou must enter a passcode to access the Service menu ServiceService Should be used by ISF-certified technicians onlyInput Names Absolutely necessary, as it may cause artifacts in the image Operation Operation Operation 64 and ISF Day/Night Memory Presets Lamp and Filter Replacement Maintenance and TroubleshootingLamp Replacement Removing the Lamp Lens Replacement Removing the Primary Lens Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Configure Lens Motor Error Codes VX-44d/-55d Error CodesCode Description General Lamp FailuresTipm Image Processor Code Description Power and CoolingBuilt-In Keypad Miscellaneous Code Description Panel Driver and FormatterMaintenance and Troubleshooting Serial Command Syntax Port ConfigurationExternal Control Serial CommunicationsInput Selection Commands Serial CommandsAspect Ratio Commands Image Preset Commands Output Shift Commands Exit Return key Enter keyCommand Bits Using Discrete IR CodesWith Toggle Bit = Hex Binary Function Start Remote Control With Toggle Description Button Name Bit = IR Command ListRC5 Control Codes for the DHD Controller RC5 DataEnter VX-44d/-55d Specifications SpecificationsVX-44d/-55d Specifications Industry-Standard Specifications Theater Calibration SpecificationsPower Requirements VX-44d DimensionsDHD Controller Specifications DHD Controller SpecificationsVX-44d/-55d Dimensions VX-44d/-55d DimensionsFormat Resolution Frequency Rate Hz MHz KHz Supported Signal Timings by InputSupported Timings Supported? √ = Yes, = NoPAL-B/G/H/I 101 102 Page 020-0826-02 Rev. B April
Related manuals
Manual 114 pages 2.55 Kb

VX-55D, VX-44D specifications

The Runco VX-55D and VX-44D projectors represent a pinnacle in home theater technology, offering expansive image quality and immersive viewing experiences. Runco, known for its commitment to delivering exceptional visual performance, has integrated numerous features and advanced technologies in these models.

One of the standout features of both the VX-55D and VX-44D is their native 1080p resolution, delivering stunningly sharp images with vibrant colors that capture the finest details. This high definition capability ensures that viewers can enjoy their favorite movies, sports, and gaming content with unparalleled clarity. The projectors utilize the latest DLP (Digital Light Processing) technology, which enhances brightness and color accuracy, providing a more vivid and lifelike picture.

Another impressive characteristic of the Runco VX series is its exceptional contrast ratios. With deep blacks and brilliant whites, these projectors offer a dynamic range that brings out subtle details in both shadow and highlight areas. This contrast performance is particularly beneficial for watching films in darker environments, where the depth of imagery is crucial for immersion.

In terms of color processing, the VX-55D and VX-44D incorporate Runco's proprietary ColorPalette technology. This system ensures accurate and rich color reproduction by utilizing a wide color gamut, allowing viewers to experience content as the creators intended. Coupled with advanced color management capabilities, users can further tweak their viewing experience to match their preferences.

The integration of flexible installation options is another highlight of these projectors. They support up to 10-point digital keystone correction, making setup simple and adaptable to various room configurations. This flexibility ensures that no matter the space, users can achieve a perfectly aligned and geometrically accurate image.

Runco has also designed the VX-55D and VX-44D with user-friendly interfaces, including intuitive remote controls and on-screen menus. Both projectors come equipped with multiple HDMI inputs, allowing users to connect various devices seamlessly. Additionally, they support 3D content playback, a feature that has become increasingly important for enhancing the cinematic experience.

Energy efficiency is a consideration in the design of these projectors as well, making them not only high-performance devices but also more sustainable than many of their counterparts. With a sleek aesthetic, the Runco VX-55D and VX-44D can seamlessly blend into any home theater setup, adding a touch of elegance while providing an extraordinary viewing experience.

In summary, the Runco VX-55D and VX-44D projectors are characterized by their high-definition resolution, advanced DLP technology, rich color processing, and flexible installation options, making them ideal choices for any home theater enthusiast looking to elevate their viewing experience.
Top Page Image Contents