Runco VX-2000d manual Tip

Page 62

Operation

Remote Control: The Remote Control menu shows you the primary and secondary infrared (IR) codes to which the VX-2000d will respond. By default, both are set to 17. You can change these codes if either:

•Another device in the theater (a DVD player, for example) is responding to commands from the VX-2000d/DHD remote control (Figure 2-5)in ways that are unpredictable or undesirable.

•You have multiple VX-2000d projectors and want to control them independently, as opposed to broadcasting commands from a single remote to all of them. In this scenario, you can use multiple remotes programmed to use different IR codes. Or, you can use a single remote and change the IR code as needed to address a specific projector.

Tip

Note

Use the DHD Controller front-panel keypad to change the projector IR code. Then, change the code sent by the remote to match as described below.

Do not change the “Type” setting in this menu.

When you change a remote code on the VX-2000d, you must re-program the VX-2000d/DHD remote control to send that same code. To do this:

1. Using a straightened paper clip or similar object, press and hold the CODE button on the remote control for approximately three seconds, or until the red LED on the remote lights solid red.

2. Enter a new two-digit code between 00 and 31 inclusive. Include a leading zero for single-digit codes; for example, enter 9 as “09.”

3.The LED turns off to confirm the code change. If you enter an invalid code, the LED flashes for three or four seconds. Try again, entering a valid code.

Display Device: The options in the Display Device menu allow you to change the picture orientation, adjust the amount of overscan and access other projector-specific functions.

•Configure: Select Configure from the Display Device menu. Then:

•Orientation: Select Orientation to change the picture orientation to suit the method of installation (Floor Front, Floor Rear, Ceiling Front or Ceiling Rear).

•Overscan: Refer to Overscan on page 46.

•Lamp Power: Select Lamp Power from the Display Device menu to adjust the lamp output level. You can choose to run the lamp as bright as possible (“1”) or you can choose the lower setting (“0”). Generally, lower lamp output can prolong the life of the lamp, but decreases brightness.

•Fan Mode: If the projector is being used in a high-altitude environment, use the Fan Mode control to prevent it from overheating. Set it to High Altitude (“1”) to run the fan at high speed; set it to Normal (“0”) to run the fan at normal speed.

•Lamp Hours: To display the number of hours that the lamp has been in service, press or to highlight Lamp Hours.

50

Runco VX-2000d Owner’s Operating Manual

Page 61 Page 63
Image 62
Page 61 Page 63
Contents VX-2000d Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation On-Screen Menus for 1080i Digital or 1080p Signals Table of Contents List of Figures List of Figures Xii Introduction About This ManualSignificance. They also provide supplemental information Using This ManualCertain features Degrade performance or cause a malfunctionDescription, Features and Benefits Format screenOptional Accessories Controls and Functions VX-2000d at a GlanceVertical Lens Shift VX-2000d Rear Panel Wired IR 3.5-mm, mini phono jackRS-232C Input RJ-11 female connector DHD Controller Front Panel Virtualwide 2.35 is available only on the VX-2000d/CineWideEnter Button Outputs 1. Hdmi OUT Component Video RCA connectorsDHD Controller Rear Panel Inputs 2. Hdmi 1 / Hdmi 2 DigitalComLink RS-232 Output Video 1 / S-VIDEOVolt 750 mA Trigger Outputs VX-2000d Remote Control Unit DHD Controller/VX-2000d Remote ControlVideo On / OFFCursor Buttons Comp ComponentANA Anamorphic Memory Preset ButtonsAspect Ratio Selection Buttons 4X3 Standard 43Not used Only trained service personnel should use the built-inVX-2000d Built-In Keypad Controls and Functions Battery Installation InstallationRemote Control OperationOther surfaces Step Procedure For Details, Refer to Quick SetupInstallation specialist Projector calibration Analog 1080i Lower-resolution signalsConsiderations InstallationInstallation Type Ambient LightThrow Distance Vertical and Horizontal Ceiling InstallationFloor Installation PositionFolded Optics Other ConsiderationsMounting VX-2000dYou Cannot connect signal sources directly to the VX-2000d Connections to the VX-2000d and DHD ControllerController Connecting SourceComponents to the DHD Hdmi Connections See FigureDigital DTV RGB or Component Video Connections See Digital DTV RGB or Component Video ConnectionsAnalog Computer RGB Connections See Figure Personal ComputerComposite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcAutomation System to Connecting a PC orConnecting 12-Volt DHD ControllerConnecting an External IR Receiver to the DHD Controller Built-in IR sensor on the DHD Controller is disabledConnecting to AC Power Turning on the PowerAdjusting the Picture Orientation You must enter a passcode to access the Service menuVertical Lens Shift Primary Lens AdjustmentsFocus and Zoom Installing and Adjusting the CineWide Anamorphic Lens It is extremely important that the primary lens is properlyAdjusting the Lens Height Y Installation Operation Input Source ISF PresetsService Aspect RatioAspect Ratio Main MenuInput Source Aspect Ratio Settings Aspect Ratio DescriptionPicture Picture Brightness Contrast Color Tint SharpnessTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Left/Right Up/Down Width Height OverscanInformation ISF PresetsISF Presets ISF Night ISF Day Custom Save Factory Default Serial Num Hardware Firmware 0100.001A Date Oct 19Calibration You must enter a passcode to access the Calibration menuLow-lights Offset provides finer adjustment Gain/Offset Refer to ISF Night Display Color, above Service Button takes you from top to bottom in the left column, thenTip Auto ADC Bandwidth Auto YPbPr Input ResolutionHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV On-Screen Menus for 1080i Digital or 1080p Signals White Balance Picture AdjustAdvanced HD/RGB AdjVX-2000d Main Menu 1080i Digital or 1080p Sources Only Picture Adjust LanguageBrightness slightly Picture Memory Description Setting ISF NightRemote Control Key RoomEffects of Primary Color Hue Adjustments Picture Adjust AdvancedWhite Balance White BalanceBelow to Off, the LED function is automatically set to On Overscan 480i/480p signals only Refer to Overscan onHD/RGB Adj Lamp Hours read-onlyRefer to Lamp Hours onRefer to page 59 is automatically set to On Orientation Refer to Adjusting the Picture Orientation onOSD Language setting Runco Technical SupportMaintenance and Troubleshooting Lamp ReplacementTroubleshooting Tips Symptom Possible Causes SolutionTroubleshooting Chart Maintenance and Troubleshooting Command RS-232 Connection and Port ConfigurationSerial Command Syntax Value Description Min/max Stored? Power On/Off CommandsAspect Ratio Commands VIRTUAL235 YESBrightness Iheight Bkgnd Enter key Command Parameter Value Description Min/maxRatio Specifications VX-2000d SpecificationsPower Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsDHD Controller Specifications VX-2000d Dimensions VX-2000d DimensionsPage RUMA-009330 Runco CL-810 Owner’s Operating Manual
Related manuals
Manual 90 pages 18.52 Kb

VX-2000d specifications

The Runco VX-2000d is a premium home theater projector that combines cutting-edge technology with a commitment to delivering extraordinary image quality. Renowned among enthusiasts for its exceptional performance, the VX-2000d caters to both the casual viewer and the most discerning cinephile, making it a standout option in the world of home entertainment.

One of the primary features of the Runco VX-2000d is its native 1080p resolution, which ensures that images are crisp, detailed, and vibrant. With a resolution of 1920 x 1080 pixels, this projector capitalizes on High Definition content, enabling viewers to experience movies and shows as the directors intended. Coupled with high brightness levels and a remarkable contrast ratio, the VX-2000d exhibits deep blacks and brilliant colors, enhancing the overall viewing experience.

The VX-2000d incorporates advanced DLP (Digital Light Processing) technology that provides remarkable color accuracy and consistency across a variety of content. The use of the latest imaging chips and sophisticated optics creates lifelike imagery that draws viewers into the action. Additionally, this projector supports a wide color gamut, allowing it to reproduce a broader range of colors for enhanced realism.

Another highlight of the Runco VX-2000d is its sophisticated lens system. The projector features a high-quality glass lens that minimizes optical distortion while ensuring sharp focus across the entire image. Its motorized lens shift, zoom, and focus functionalities allow for easy installation and flexibility in positioning the projector within various home theater setups.

The VX-2000d also supports various video formats, including 24p film and 1080p/60, making it versatile for different types of content. Also, with its built-in proprietary video processing technology, the projector upscales standard-definition and high-definition content to optimized viewing experiences.

Furthermore, the Runco VX-2000d is equipped with a range of connectivity options, including HDMI, Component, and VGA inputs, ensuring compatibility with numerous devices such as Blu-ray players, gaming consoles, and streaming devices.

With its combination of excellent build quality, robust performance, and impressive features, the Runco VX-2000d remains a top choice for enthusiasts seeking an unparalleled home theater experience. Whether enjoying action-packed films or serene nature documentaries, this projector immerses viewers in a cinematic journey that captivates the senses.
Top Page Image Contents