Sharp PG-C45X operation manual Setup, Using the Adjustment Feet

Page 31

Setup

Using the Adjustment Feet

The height of the projector can be adjusted using the adjustment feet at the front and back of the projector when the surface the projec- tor is placed on is uneven or when the screen is slanted.

The projection of the image can be made higher by adjusting the projector when it is in a location lower than the screen.

1 Press HEIGHT ADJUST.

2 Lift the projector to adjust its height and remove your finger from HEIGHT ADJUST.

3 Rotate the adjustment feet at the back of the projector for fine adjustment.

Note

•When returning the projector to its original position, hold the projector firmly, press HEIGHT ADJUST and then gently lower it.

•The projector is adjustable up to approxi- mately 12 degrees on the front and 3 degrees on the back from the standard po- sition.

Info

•Do not press HEIGHT ADJUST when the adjustment foot is extended without firmly holding the projector.

•Do not hold the lens when lifting or lower- ing the projector.

•When lowering the projector, be careful not to get your finger caught in the area between the adjustment foot and the projector.

HEIGHT ADJUST button

Adjustment foot

Adjustment feet

Up

Down

Connections and Setup

-27

Image 31

Contents PG-C45X Model No. PG-C45X Serial No Special Note for Users in the U.K Page Introduction Product Disposal New Edge Up-Scaling Outstanding FeaturesColor Management System Noise ReductionContents Appendix Power-Cord Protection CleaningAccessories Power SourcesWall or Ceiling Mounting Damage Requiring ServiceReplacement Parts Safety CheckRest your eyes occasionally Avoid locations with high or low temperatureUsing the projector in other countries Temperature monitor functionFor Macintosh To install Acrobat Reader from the CD-ROMFor other operating systems For other languages For WindowsProjector Front and Top View Part NamesProjector Rear View Using the Kensington LockRemote Control Top View Remote Control Front ViewPart Names Inserting the Batteries Using the Remote ControlAvailable Range of the Remote Control When using the remote controlSupplied accessories AccessoriesOptional cables Connections and Setup An audio cable commercially available See Connecting the Projector to Other DevicesBefore Connecting This projector can be connected toConnecting the Power Cord Ferrite core Connecting to a Computer Using the RGB CablePlug and Play function when connecting to a 15-pin terminal Connecting to Video Equipment Cable Connecting to Component Video EquipmentConnecting to an Amplifier or Other Audio Components Connecting to an AmplifierControlling the Projector by a Computer Watching Images on Both the Projector and a Monitor Connecting to a MonitorPress or while using presentation software on your computer Using the Wireless Pre- sentation FunctionButton Connecting the Remote Control to the Projector Using as a Wired Remote ControlUsing the Adjustment Feet SetupFocus ring Zoom knob Adjusting the LensOut Zoom Throw Distance Setting up the ScreenStretch Mode Normal ModeScreen Size and Projection Distance AN-C12MZ Throw ratio 11.18 to Projection from behind the screen Projecting a Reversed/Inverted ImageBasic Operation Image Projection Basic ProcedurePlug the power cord into the wall outlet Press on the projector or on the remote controlVolume buttons Press , , or on the remote control to select the Input modePress \ or to select Lan Selecting the On-screen Display LanguagePress to temporarily turn off the sound PressPress or to select the de- sired language, and then press Test pattern Press , , \ and to adjust the Keystone correctionCorrecting Trapezoidal Distortion Keystone button Enter button Undo button ButtonsUndo button Sub menu Menu Bar ItemsMain menu Sub menu Input 3 / 4 ModeMenu Selections Adjustments Using the Menu ScreenMenu Bar Main Menu Enter button Buttons Menu button Press or to select the item you want to adjust Press \ or to select the menu you want to adjustPress \ or to adjust the item selected Press or to select the item you want to set Menu Selections SettingsEnter button Buttons Menu button Cursor shifts to the sub menu Adjusting Image Preferences Adjusting the PictureSelecting the Signal Type Progressive Mode When Auto Sync is OFF Adjusting Computer ImagesSaving Adjustment Settings Special Mode Settings Selecting Adjustment SettingsChecking the Input Signal Auto Sync button Auto Sync AdjustmentAuto Sync Display Function Screen display during Auto SyncEasy to Use Functions Switching the Picture Display Using Different Input Signals Selecting the Picture Display ModeResize button Screen display of the picture display mode Video Freezing a Moving Image Displaying a Still ImageFreeze button Displaying an Enlarged Portion of an Image Enlarging a Specific Portion of an ImageButtons Enlarge Enlarge/ Reduce buttons Gamma Correction Function Adjusting Gamma CorrectionDisplaying the Inset Picture Displaying Dual Pictures Pict in PictPress to move the inset pic- ture This function can be used to display a black screen Black Screen FunctionBlacking out the Pro- jected Image To return to the original projected image, press againButtons Break Timer button Displaying the Break TimerDisplaying and Setting the Break Timer Press to cancel the break timerSelecting the Target Color Selecting the Color Reproduction ModeSetting the Chromatic Value of the Target Color Setting the Brightness of the Target ColorSetting the Hue of the Target Color Overview of All Color Settings Resetting User-Defined Color SettingsSetting on/off the Inter- nal Speaker Setting the Audio Output TypeSetting on/off the Internal Speaker Setting the Audio Out- put TypeAuto Search Function Using Auto SearchTurning Off On-screen Display Setting On-screen DisplayVideo Digital Noise Reduction DNR System Reducing Image NoiseSetting the Video System Setting the Video SystemCapturing the Image Saving Projected ImagesDeleting the Captured Image Selecting a Startup Image Setting a Background ImageSelecting a Startup Image Selecting a Background ImageSetting the Power Save Mode Selecting the Economy ModeMonitor Out/RS-232C Off Function Checking the Remaining Lamp Life Percentage Automatic Power Off FunctionSelecting the Economy Mode Displaying the Remaining Lamp Life PercentageLocking the Operation Buttons on the Projector Setting the Projection ModeSetting up the Keylock Reversing/Inverting Projected ImagesSelecting the Transmission Speed RS-232C Canceling the Keylock SettingSelecting the Transmis- sion Speed RS-232C Entering the Password Setting up a PasswordIf You Forget Your Password Changing the PasswordEntering the Keycode Setting the Anti-TheftEnter the same 4-digit keycode in Reconfirm Changing the KeycodeReturning to Default Settings Initializing the SettingsOverview of All Menu Settings Displaying the Adjustment SettingsAppendix Cleaning the exhaust and intake vents MaintenanceCleaning the projector Cleaning the lensRemove the bottom filter cover Cleaning and replacing the bottom air filterTurn off the power and discon- nect the power cord Replacing the Air FilterReplace the air filter Clean the air filterReplace the filter cover About the temperature warning indicator Maintenance IndicatorsAbout the lamp replacement indicator Maintenance Indicators Lamp Regarding the LampReplacing the Lamp Change the air filter Removing and Install- ing the Lamp UnitPress on the projector to turn off the power Disconnect the power cordResetting the Lamp Timer RGB Input Component Input Connecting Pin AssignmentsCommunication conditions RS-232C Specifications and Command SettingsCommands PC controlRS-232C Specifications and Command Settings Options Control Contents Function and transmisson codes Wired Remote Control Terminal SpecificationsSpecifications of wired remote control input Sharp remote control signal formatComputer Computer Compatibility ChartTroubleshooting Troubleshooting For Sharp Assistance Ntsc 3.58/NTSC 4.43/PAL/PAL-M/PAL-N/PAL 60/SECAM SpecificationsUnits inches mm DimensionsAdvanced intelligent compression Glossary100 Index101 StretchSharp Corporation