Sharp PG-C45X operation manual Setting the Video System

Page 70

Setting the Video System

The video input system mode is preset to “Auto”; however, a clear picture from the con- nected audio-visual equipment may not be received, depending on the video signal differ- ence. In that case, switch the video signal.

Setting the Video

System

Select “Video System” in the “Options

(1)” menu on the menu screen.

➝ For operating the menu screen, see pages 42 to 45.

Note

• The video signal can only be set in IN-
PUT 3 or INPUT 4 mode.
• In “Auto”, images are displayed in PAL
even if PAL-N or PAL-M input signals are
received.	PAL	When connected to PAL video equipment.
	SECAM	When connected to SECAM video
		equipment.
	NTSC4.43	When reproducing NTSC signals in
		PAL video equipment.
	NTSC3.58	When connected to NTSC video equipment.

-66

Image 70

Contents PG-C45X Model No. PG-C45X Serial No Special Note for Users in the U.K Page Introduction Product Disposal Noise Reduction Outstanding FeaturesColor Management System New Edge Up-ScalingContents Appendix Power Sources CleaningAccessories Power-Cord ProtectionSafety Check Damage Requiring ServiceReplacement Parts Wall or Ceiling MountingTemperature monitor function Avoid locations with high or low temperatureUsing the projector in other countries Rest your eyes occasionallyFor Windows To install Acrobat Reader from the CD-ROMFor other operating systems For other languages For MacintoshPart Names Projector Front and Top ViewUsing the Kensington Lock Projector Rear ViewRemote Control Top View Remote Control Front ViewPart Names When using the remote control Using the Remote ControlAvailable Range of the Remote Control Inserting the BatteriesSupplied accessories AccessoriesOptional cables Connections and Setup This projector can be connected to Connecting the Projector to Other DevicesBefore Connecting An audio cable commercially available SeeConnecting the Power Cord Connecting to a Computer Using the RGB Cable Ferrite corePlug and Play function when connecting to a 15-pin terminal Connecting to Video Equipment Connecting to Component Video Equipment CableConnecting to an Amplifier Connecting to an Amplifier or Other Audio ComponentsControlling the Projector by a Computer Connecting to a Monitor Watching Images on Both the Projector and a MonitorPress or while using presentation software on your computer Using the Wireless Pre- sentation FunctionButton Using as a Wired Remote Control Connecting the Remote Control to the ProjectorSetup Using the Adjustment FeetFocus ring Zoom knob Adjusting the LensOut Zoom Setting up the Screen Throw DistanceStretch Mode Normal ModeScreen Size and Projection Distance AN-C12MZ Throw ratio 11.18 to Projecting a Reversed/Inverted Image Projection from behind the screenBasic Operation Press on the projector or on the remote control Basic ProcedurePlug the power cord into the wall outlet Image ProjectionPress , , or on the remote control to select the Input mode Volume buttonsPress Selecting the On-screen Display LanguagePress to temporarily turn off the sound Press \ or to select LanPress or to select the de- sired language, and then press Keystone button Enter button Undo button Buttons Press , , \ and to adjust the Keystone correctionCorrecting Trapezoidal Distortion Test patternUndo button Menu Bar Items Sub menuInput 3 / 4 Mode Main menu Sub menuMenu Selections Adjustments Using the Menu ScreenMenu Bar Main Menu Enter button Buttons Menu button Press or to select the item you want to adjust Press \ or to select the menu you want to adjustPress \ or to adjust the item selected Press or to select the item you want to set Menu Selections SettingsEnter button Buttons Menu button Cursor shifts to the sub menu Adjusting Image Preferences Adjusting the PictureSelecting the Signal Type Progressive Mode When Auto Sync is OFF Adjusting Computer ImagesSaving Adjustment Settings Special Mode Settings Selecting Adjustment SettingsChecking the Input Signal Screen display during Auto Sync Auto Sync AdjustmentAuto Sync Display Function Auto Sync buttonEasy to Use Functions Switching the Picture Display Using Different Input Signals Selecting the Picture Display ModeResize button Screen display of the picture display mode Video Freezing a Moving Image Displaying a Still ImageFreeze button Displaying an Enlarged Portion of an Image Enlarging a Specific Portion of an ImageButtons Enlarge Enlarge/ Reduce buttons Adjusting Gamma Correction Gamma Correction FunctionDisplaying the Inset Picture Displaying Dual Pictures Pict in PictPress to move the inset pic- ture To return to the original projected image, press again Black Screen FunctionBlacking out the Pro- jected Image This function can be used to display a black screenPress to cancel the break timer Displaying the Break TimerDisplaying and Setting the Break Timer Buttons Break Timer buttonSelecting the Color Reproduction Mode Selecting the Target ColorSetting the Chromatic Value of the Target Color Setting the Brightness of the Target ColorSetting the Hue of the Target Color Resetting User-Defined Color Settings Overview of All Color SettingsSetting the Audio Out- put Type Setting the Audio Output TypeSetting on/off the Internal Speaker Setting on/off the Inter- nal SpeakerUsing Auto Search Auto Search FunctionReducing Image Noise Setting On-screen DisplayVideo Digital Noise Reduction DNR System Turning Off On-screen DisplaySetting the Video System Setting the Video SystemCapturing the Image Saving Projected ImagesDeleting the Captured Image Selecting a Background Image Setting a Background ImageSelecting a Startup Image Selecting a Startup ImageSetting the Power Save Mode Selecting the Economy ModeMonitor Out/RS-232C Off Function Displaying the Remaining Lamp Life Percentage Automatic Power Off FunctionSelecting the Economy Mode Checking the Remaining Lamp Life PercentageReversing/Inverting Projected Images Setting the Projection ModeSetting up the Keylock Locking the Operation Buttons on the ProjectorSelecting the Transmission Speed RS-232C Canceling the Keylock SettingSelecting the Transmis- sion Speed RS-232C Setting up a Password Entering the PasswordChanging the Password If You Forget Your PasswordSetting the Anti-Theft Entering the KeycodeChanging the Keycode Enter the same 4-digit keycode in ReconfirmInitializing the Settings Returning to Default SettingsDisplaying the Adjustment Settings Overview of All Menu SettingsAppendix Cleaning the lens MaintenanceCleaning the projector Cleaning the exhaust and intake ventsReplacing the Air Filter Cleaning and replacing the bottom air filterTurn off the power and discon- nect the power cord Remove the bottom filter coverReplace the air filter Clean the air filterReplace the filter cover About the temperature warning indicator Maintenance IndicatorsAbout the lamp replacement indicator Maintenance Indicators Lamp Regarding the LampReplacing the Lamp Disconnect the power cord Removing and Install- ing the Lamp UnitPress on the projector to turn off the power Change the air filterResetting the Lamp Timer Connecting Pin Assignments RGB Input Component InputPC control RS-232C Specifications and Command SettingsCommands Communication conditionsRS-232C Specifications and Command Settings Options Control Contents Sharp remote control signal format Wired Remote Control Terminal SpecificationsSpecifications of wired remote control input Function and transmisson codesComputer Compatibility Chart ComputerTroubleshooting Troubleshooting For Sharp Assistance Specifications Ntsc 3.58/NTSC 4.43/PAL/PAL-M/PAL-N/PAL 60/SECAMDimensions Units inches mmGlossary Advanced intelligent compressionIndex 100Stretch 101Sharp Corporation